SmartDome Camera SCC-C6405(P) Owner’s Instructions Benutzerhandbuch Manuel d’instruction Manual del usuario Istruzioni per l’uso Part : AB68-00504B (02) Printed in China E D F Es I
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. 11. 12. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings, Install in accordance with the manufacturer's instructions. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat.
6. Do not place conductive objects (e.g., screwdrivers, coins, and metal things) or containers filled with water on top of the camera. (Doing so may cause personal injury due to fire, electrical shock, or falling objects.) 7. Do not install the unit in humid, dusty, or sooty locations. (Doing so may cause fire or electrical shock.) 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center.
Before Usage This is a basic instruction manual for the SCC-C6405(P) user. It contains all the instructions needed to use the SCC-C6405(P) from a simple introduction of the control locations and functions of the SCC-C6405(P) to installation methods in the set up menu. We recommend all users of the SCC-C6405(P) from the advanced user who has used similar cameras before to the general user to read the instruction manual before using.
Table of contents Before Usage...............................................................................................1-1 Chapter 1 SCC-C6405(P) Overview ...........................................................1-5 SCC-C6405(P) Introduction ...........................................................1-6 Locations of Control .......................................................................1-7 FRONT...........................................................................................
Chapter 1 SCC-C6405(P) Overview In this chapter we will briefly introduce the SCC-C6405(P) and show main functions, locations of control and Switch Setting. SCC-C6405(P) Introduction SCC-C6405(P) is a zoom lens built in smart dome camera which provides you with the best monitoring function in connection with CCTV at banks or companies. E The SCC-C6405(P) is a high quality surveillance camera using x22 zoom lens and digital zoom IC, it can catch clear images up to 220 times.
Locations of Control FRONT BACK AC 24V OUT E POWER AC 24V OUT POWER 1-7 1-8
ADAPTER CONNECTION INITIAL SETTING SCC-C6405(P) Adapter BOARD CAMERA ADDRESS SETUP Use SW701, SW702, or 703 for Camera Address setup. You may allocate up to 255 addresses by using SW701 to set the 3rd digit, SW702 the 2nd digit, and SW703 the 1st digit. EX) In case of Camera Address 1, see the following figure for setup. E SW701 SW703 SW702 Setting communication Protocol Use number 1~4 PIN of SW704 to set communication Protocol.
Setting RS-422A/RS-485 termination 1 Chapter 2 SCC-C6405(P) Installation 2 As it is shown in the structure map, when Controller and RS-422A/RS485 is connected it should be terminated according to the Cable feature of impedance on the each end of the transmitting line to transfer the signals in long distance by controlling the reflection of the signals to the lowest.
Preparing the Cables Before Installing Checking Package Contents Please check that all components listed below are included in the package: To install and use the SCC-C6405(P), the following cables should be prepared. Power Adapter Cable The cable that plugs into the SCC-C6405(P) power input receptacle has the rated voltage of AC24V, 1.5A. Check the rated voltage before using the cable.
Installing SCC-C6405(P) Cable Connection 1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT) Installation Precautions 1) Make sure that the installation site can sufficiently support a minimum of four times the net weight of the SCC-C6405(P) SmartDome Camera and other accessories. 2) Install in an area where the space above the ceiling board is over 18 cm (7 in.) high. 3) Use the supplied screws to fasten the camera to the bracket assembly.
3) INDOOR HOUSING (SHG-120) This housing is used for installing the SmartDome Camera to an indoor wall or a ceiling. 5) CEILING MOUNT ADAPTOR (SADT-100CM) This adaptor is used for installing the indoor housing or the outdoor housing for the SmartDome Camera to a concrete ceiling. E 4) OUTDOOR HOUSING (SHG-220) This housing is used for installing the SmartDome Camera to an outdoor wall or a ceiling.
Installing the Camera 5. [Figure 5] Match the BRKT-ANCHOR and CAMERA ADAPTER and use 4screws (PH M4 x 8) to assemble them. 1. [Figure 1] Install the structure on the ceiling. (Refer to Installation reference for the Length of the structure) [Figure 5] 6. Pull the safety wire from the case body, and assembly it to the camera holder. [Figure 6] * Built in by the builder of the structure E [Figure 1] Length of ceiling Hole 2. Make a hole in the ceiling where the camera will be installed.
Structure of the Setup Menu Chapter 3 Setup Menu Overview In this chapter, we will look over the Setup Menu of the SCC-C6405(P), First we'll look over the overall structure of the Setup Menu, and then we'll look at the functions of each menu. 3-1 CAMERA SET CAMERA ID V-SYNC COLOR/BW MOTION DET ZOOM SPEED DIGITAL ZOOM EXIT ON.../OFF INT/LINE... COLOR/BW.../AUTO... ON.../OFF 1/2/3/4 OFF/X2~X10 QUIT/SAVE/PRESET IRIS SHUTTER AGC MOTION WHITE BAL DIS FOCUS MODE SPECIAL EXIT ALC.../WDR...
ALARM SET ALARM PRIORITY SET ALARM IN SET 1~4 1~4 1~4 1~4 QUIT/SAVE ALARM1 NO/NC/OFF ALARM2 NO/NC/OFF ALARM3 NO/NC/OFF ALARM4 NO/NC/OFF EXIT QUIT/SAVE ALARM OUT SET AUTO SET ALARM1 ALARM2 ALARM3 ALARM4 EXIT ALARM1 ALARM2 ALARM3 ALARM4 MOTION EXIT ALARM1 ALARM2 ALARM3 ALARM4 MOTION EXIT AUX OUT CONTROL 1~3 1~3 1~3 1~3 1~3 QUIT/SAVE OFF/1~3/HALF1/HALF2/FULL/SCAN1~4 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4 OFF/1~3/HALF1/HALF2/FULL/SCAN1~4 QUI
COLOR/BW (CAMERA SET) (CAMERA ID) CAMERA ID V-SYNC COLOR/BW MOTION DET ZOOM SPEED DIGITAL ZOOM ON... INT COLOR OFF 3 OFF A BCDEFGHIJKL M N O PQ R S T U V W X YZ0 1 2 3 4 5 6 7 8 9 EXIT QUIT ➜ Press [Enter] : ! - + ✽ ()/ SP ï î SP LOCATION... RET SCC-C6405P........ * " ... " Means there are Sub Menus. V-SYNC In the V-SYNC menu, vertical synchronization can be selected.
MOTION DET ZOOM SPEED In MOTION DET, you can set the Motion Detection function, Motion Detection Sensitivity, and the Area of Motion Detection. If the Motion Detection function is set, the movement of an intruder can be detected. When motion is detected, it sets off the Alarm signal of the Controller. In the ZOOM SPEED menu you can select the speed of the ZOOM Key (Tele/Wide). Use the [Left] or [Right] keys in the ZOOM SPEED menu to select the speed. 1 : Magnification x 22 takes about 18 seconds.
2. VIDEO SET MENU IRIS There is a function to automatically adjust IRIS to the incoming light level. Owing to this function, you may set up the brightness level yourself. The ALC(Auto Light Control) menu allows you for video output level setup. The WDR(Wide Dynamic Range) menu allows you to set up the WDR level and the FLICKERLESS function. ALC Choose the ALC of the IRIS item and press [ENTER] and set he submenu to the Video Output level and BLC will be shown.
AGC WHITE BAL The AGC menu was designed to provide you with brighter screen supposed you photographed any subject in the dark resulting in less brighter image than regulated. AGC menu setup is available only when the SHUTTER menu is set to Fast Shutter or Off. Press either Left and Right to go to LOW or HIGH and the AGC function will be activated. LOW is use to lower the maximum AGC GAIN and HIGH raise the maximum AGC GAIN.
You can select one of four modes for white balance adjustment as follows: - ATW1/ATW2(Auto-Tracing White Balance Mode): In these modes, the color temperature is monitored continuously and thereby white balance is set automatically. The following are the approximate supported color temperature ranges in these modes. ATW1 : 2500K ~ 9300K(✻1) ATW2 : 2000K ~ 10000K(Mode recommended for sodium lighting)(✻2) ✻ 1. If the color temperature is out of this range in ATW1 mode, proper white balance may not be obtained.
3. PRESET POSITION SET This is the menu that user sets the PAN/TILT location, Zoom/Focus, and screen condition, so the camera can monitor the presetting area on demand. A total of 128 presets are available. Among the 128 PRESETS, PRESET 1: ALARM1, PRESET 2: ALARM2, PRESET 3: ALARM3, PRESET 4: ALARM4,PRESET 5: set as special preset corresponding MOTION. From "POSITION SET...
BLANK ALL ABOVE 4. ZONE SET The ZONE SET menu includes the setup of PRIVACY ZONE, ZONE DIRECTION, and ZONE AREA. The available angle for setup ranges from OFF/0/-10 to -90 and the area above a set angle will be regarded as the ZONE area. BLANK ALL BELOW * * MAIN MENU * * CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... SYSTEM INFO... (ZONE SET) ➜ Press [Enter] PRIVACY ZONE ZONE DIR SET ZONE AREA SET ... ON...
SET ZONE AREA SET ZOOM Press [ENTER] at the “SET ZONE AREA...” position to enter the PRIVACY ZONE setup screen. Control PAN/TILT/ZOOM to select 4 apexes of the PRIVACY ZONE area and the rectangular PRIVACY ZONE area will be completed. Press [ENTER] at the “SET ZOOM...” position to enter the ZOOM setup screen. After ZOOM setup, the PRIVACY ZONE function will be in action only at the higher magnification than the Zoom magnification as set. PRIVACY ZONE SET 0 SET ZONE AREA SET ZOOM REVERSE ON...
ZONE DIR SET LOCATION Press the [Enter] key in the “ZONE DIR SET ON…” mode to enter the NORTH SET screen. MAP. Move PAN to set the NORTH position and press [ENTER]. Based on the North position,the direction of N(North), NE(North-East), E(East), SE(South-East), S(South), SW(South-West), W(West), NW(North-West) is displayed whenever you move PAN. The “LOCATION...” menu designates the left/right LIMIT positions of ZONE AREA. Enter the setup screen to move PAN, then select a start position and press [ENTER].
5. AUTO SET DIRECTION The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is able to set up the AUTO PLAY motion. This sets up the movement direction of the START to END location (PAN location standard) "RIGHT " : "LEFT " : AUTO PAN After selecting the locations of two points (PAN/TILT) of START and END, it loops continuously in the set up SPEED. The number of AUTO PAN is up to 4. E * * MAIN MENU * * CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET...
* * MAIN MENU * * CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... SYSTEM INFO... AUTO PLAY (AUTO SET) AUTO PAN PATTERN SCAN AUTO PLAY ➜ Press [Enter] 1... 1... 1... ... ➜ Press [Enter] RET ➜ PATTERN SET 1 SET START POSITION AND ENTER (AUTO SET) AUTO PAN PATTERN SCAN AUTO PLAY PATTERN SET 1 After PATTER START position setup, press [ENTER]. SCAN SCAN sets the direction of PRESET movement during “SCAN” operation.
AUTO SET 6. ALARM SET It consists of 4 ALARM INPUTs and 3 ALARM OUTs.It can sense an ALARM input from exterior SENSORs and it performs with PRESET or PATTERN function and outputs the ALARM OUT signals. The Alarm will be recognized only when its input lasts more than 150ms and the alarm operation time depends on the Preset Dwell time corresponding to the alarm and whether AUTO is involved. * * MAIN MENU * * CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... SYSTEM INFO...
TURBO P/T This function doubles up the speed of PAN/TILT movement by manual operation of PAN/TILT. The speed may go up to 180°/sec(PAN). AUTO CAL This function turns on or off Auto Calibration. SCC-C6405(P) has the Auto Calibration function to improve the precision of LENS and PAN/TILT motor. You may set to OFF/6H/12H/18H/24H. Without user’s key input for the time designated by the user, A.C. will appear on the screen while initializing LENS and PAN/TILT.
9. SHORT KEYS SSC-1000 or SSC-2000 Controller supports the following short keys.
Product specifications SCC-C6405 NO Items 1 Product Type Contents 2 Power Input 3 Power Consumption 4 Broadcasting Type 5 Image Device 6 Effective Pixels - 768(H) x 494(V) 7 Scanning Mode - 525 Lines, 2:1 Interlace - AC 24 ± 10% (60Hz ± 0.3Hz) - 18W - NTSC STANDARD COLOR SYSTEM - 1/4 inch WDR compatible Exview HAD CCD Scanning line Frequency 9 Synchronization Mode 10 Resolution - 480 TV LINES 11 S/N Ratio - 50dB (AGC OFF) 12 Min.
Cautions SCC-C6405P NO Items 1 Product Type 2 Power Input 3 Power Consumption 4 Broadcasting Type Contents - PAL STANDARD COLOR SYSTEM Image Device Effective Pixels - 752(H) x 582(V) 7 Scanning Mode - 625 Lines, 2:1 Interlace 8 Scanning line Frequency - 1/4 inch WDR compatible Exview HAD CCD • This manual will be modified according to product enhancements.