220X POWER ZOOM CAMERA SCC-C4201(P), C4203(P), C4301(P), C4303(P) Owner’s Instructions Gebrauchsanleitung Guide d’utilisation Guía del usuario Istruzioni per l’uso 220x Pow LOW er Zoo m L DIGIT AL CO IGHT LOR CAM ERA Part : AB68-00366A Printed in Korea ✽ Be sure to read the "Safety Precautions" in this manual to ensure correct use and operation of this product.
Safety Precautions The purpose of safety precautions is to prevent accidental injury or property damage. Always observe all safety precautions. ✽ The precautions are divided into "Warnings" and "Cautions" as distinguished below: Warning Ignoring this precaution may result in death or serious injury. Caution Ignoring this precaution may result in injury or damage to property. Warnings 1. Be sure to use only the standard adapter which is specified in the specification sheet.
Contents Cautions 1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibration or magnetic interference. 2. Do not install in a location subject to high temperature, low temperature, or high humidity. (Doing so may cause fire or electrical shock.) 3. Avoid a location which is exposed to direct sunlight, or near heat sources such as heaters or radiators. (Neglecting to do so may result in a risk of fire.) 4.
1 Overview 2 Part Names and Functions This camera is a high performance surveillance camera that provides a maximum of 220x zoom surveillance capability with its 22x optical zoom lens and digital zoom IC. It is a multifunction camera that is equipped with all of the key features of the existing surveillance cameras : ● E Day & Night function (SCC-C4203(P), C4303(P)) that ensures sharp and clear images even at night.
3 ☞ In Setup Menu Mode Installation - UP/ DOWN buttons: Use to move the cursor up or down. - LEFT/ RIGHT buttons: Use to move the cursor left or right, or to sequentially view the values that can be assigned to a parameter. - ENTER button: Use to select a Sub Menu item, and to accept the current value. ZOOM/ FOCUS REMOTE terminals Use to control ZOOM/ FOCUS from an external controller. Depending on the input conditions, the terminals can be set to 4 different modes.
Preparing the Cables To install and use the camera, first prepare the following cables. The requirements for the power adapter, which connects to the camera's POWER IN terminal, are as follows: ● ● Connecting the Cables 1. Connect one end of the BNC cable to the VIDEO OUT. 2. Connect the other end of the BNC cable to the VIDEO IN of the monitor.
4 4. Determine the type of power supply and set the POWER SELECTION switch accordingly. Next, plug the power adapter into a wall outlet. The requirements for the power adapter for each model are as follows: ● ● SCC-C4201(P), SCC-C4203(P) : DC12V 600mA SCC-C4301(P), SCC-C4303(P) : AC24V 300mA DC12V 600mA 5. If the camera operates normally, the following screen will be displayed for 5 seconds and then disappears.
Structure of the Setup Menu ● Structure of the Setup Menu of the SCC-C4203(P) ● Structure of the Setup Menu of the SCC-C4301(P) CAMERA ID OFF/ON... CAMERA ID OFF/ON... IRIS ALC.../MANU... IRIS ALC.../MANU... SHUTTER OFF/1/100(1/120) ~ 1/10K /AUTO X2~X128/FIX X2~X128 SHUTTER OFF/1/100(1/120) ~ 1/10K /AUTO X2~X128/FIX X2~X128 AGC OFF/LOW/HIGH AGC OFF/LOW/HIGH MOTION S.S/SLOW/NORMAL/FAST/F.F MOTION S.S/SLOW/NORMAL/FAST/F.F WHITE BAL ATW/AWC/MANU... WHITE BAL ATW/AWC/MANU...
Structure of the Setup Menu ● Structure of the Setup Menu of the SCC-C4303(P) CAMERA ID OFF/ON... IRIS ALC.../MANU... SHUTTER OFF/1/100(1/120) ~ 1/10K /AUTO X2~X128/FIX X2~X128 AGC OFF/LOW/HIGH MOTION S.S/SLOW/NORMAL/FAST/F.F WHITE BAL ATW/AWC/MANU... SPECIAL ... ENGLISH V-SYNC INT/LINE... CTRL TYPE A/B/C/D RS-485 PIP ... OFF/ON...
IRIS The level of video output to the monitor can be controlled by the iris lens according to the intensity of the incoming light. This product is equipped with an iris lens. In the ALC (Auto Light Compensation) menu, you can set the video output level. In the MANU menu, you can manually set the opening and closing of the iris.
SHUTTER AGC (MOTION) In the SHUTTER option, you can specify the speeds of the high-speed electronic shutter, auto low-speed shutter, and fix low-speed shutter. The high - speed electronic shutter supports 7 shutter speeds from 1/100 seconds to 1/10K seconds, and the auto low-speed shutter and fix low-speed shutter support 12 shutter speeds from 2x to 128x respectively.
WHITE BAL SPECIAL In the WHITE BAL option, you can set the White Balance function, which enables you to see the white color correctly under illumination of any color temperature. If you set the WHITE BAL option to ATW, the camera will continuously monitor changes in the ambient color temperature and automatically set the White Balance according to the color temperature.
☞ ☞ CTRL TYPE : You can select the A, B, C, or D mode depending on the input of the wired remote control terminal. (See page 7.) RS-485 : It sets up ADDRESS, PROTOCOL, and BAUD RATE of RS-485 communication. (BAUD RATE: 2400bps, 4800bps, 9600bps, 19200bps, 38400bps) Caution : A communication error may occur if you connect more than one camera set with an identical address. ☞ PIP : This is the Picture in Picture feature.
If you select ON and press the ENTER button, the MOTION DET screen will come up. You can set the AREA to which the Motion Detection function will be applied to either PRESET or USER. If you set the AREA option to PRESET, the Motion Detection function will be applied to the areas preset as factory defaults. If you set the AREA option to USER and press the ENTER button, you can change the area size and position and select the area where you want to apply the Motion Detection function.
In low light conditions, the IR Filter is turned OFF and the sensitivity to low light is increased by switching to the BW mode, but in bright light conditions, the IR Filter is turned ON and the sensitivity is decreased by switching to the COLOR mode. If you select AUTO and press the ENTER button, a screen from which you can set the ALARM ON/OFF, BURST ON / OFF, BW LEVEL and DWELL TIME will appear. - ALARM ON : It sends out signals through the ALARM output port in the BW mode.
5 Specifications SCC-C4201/C4203 SCC-C4201P/C4203P Item Product Type Power Supply Voltage Power Consumption Broadcast System Description - 22x Zoom Camera - DC 12V ± 10% - 5.0 W - NTSC Standard Color System Imaging Device - 1/4 inch IT CCD Effective Pixe - 768(H) x 494 (V) Scanning Method Line Frequency Synchronization Method - 525 Line, 2:1 Interlace - Horizontal : 15,734 Hz (INT) - Vertical : 59.
Specifications SCC-C4301/C4303 SCC-C4301P/C4303P Item Product Type Power Supply Voltage Power Consumption Broadcast System Description - 22x Zoom Camera - AC 24V (60Hz) or DC 12V ± 10% - 5.5W - NTSC Standard Color System Imaging Device - 1/4 inch IT CCD Effective Pixe - 768(H) X 494(V) Scanning Method Line Frequency Synchronization Method - 525 Line, 2:1 Interlace - Horizontal : 15,734 Hz(INT), 15,750 Hz(L/L) - Vertical : 59.
6 Others ZOOM/FOCUS Remote Terminals These terminals are to activate the ZOOM/FOCUS, MENU CONTROL, HOME RETURN, and AF functions by using an external controller. They could be set to one of four modes depending on the input condition: A, B, C, and D. (SPECIAL - CTRL TYPE) (Operating Voltage Range : +3V~+13V, -3V~-13V) 1 : With the menu "off", if voltage is applied for shorter than 2 seconds, the AF function will be activated, and if voltage is applied for longer than 2 seconds, the menu will be "on".
Memo Memo
