SmartDome Camera User’s Guide ENG SCC-C6433(P)/C6435(P) GER FRE SPA ITA TUR
Safety Precautions CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK) NO USER-SERVICEABLE PARTS INSIDE REFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
9. If this product fails to operate normally, contact the nearest service centre. Never disassemble or modify this product in any way. (SAMSUNG is not liable for problems caused by unauthorized modifications or attempted repair.) 10. When cleaning, do not spray water directly onto parts of the product. Doing so may cause fire or electric shock. 7. Avoid aiming the camera directly towards extremely bright objects such as sun, as this may damage the CCD image sensor. 8.
Important Safety Instructions 1. 2. 3. 4. 5. 6. 7. Read these instructions. Keep these instructions. Heed all warnings. Follow all instructions. Do not use this apparatus near water. Clean only with dry cloth. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
Contents Overview............................................................................................ 8 About this guide.............................................................................8 Product overview............................................................................8 Main features..................................................................................8 Components....................................................................................
DIGITAL ZOOM.........................................................................39 DISPLAY ZOOM........................................................................40 DISPLAY P/T.............................................................................41 EXIT..........................................................................................41 Video set .......................................................................................42 IRIS.............................................
ENG AUTO SET................................................................................66 AUX OUT CONTROL................................................................66 Other set .......................................................................................67 PROPORTIONAL P/T...............................................................67 TURBO P/T...............................................................................67 AUTO CAL.....................................................
Overview ❚ About this guide This user guide includes basic instructions for the product. It is recommended that all users read this guide before use. This guide is divided as follows: “Overview” introduces the user guide and product related information. “Installation” explains how to set and install the product. “Camera Setup” presents the structure of the Setup menu for the SCC-C6435(P)/6433(P) including a detailed explanation of the functions performed in each submenu.
NAMES OF EACH PART Your camera has the following components: ENG 1. Camera Holder Adapter 2. Camera Body 3. Zoom Lens 4. Cover-dome 5. Alarm Output: N/O, COM, N/C, AO-2, AO-1, GND 6. Alarm Input (1~8): AI-8, AI-7, AI-6, AI-5,GND, AI-4, AI-3, AI-2, AI-1, GND 7. RS-485: TXD+, TXD-, RXD+, RXD8. Power Input: 24V, EARTH, 24V 9.
Installation ❚ Before installation THINGS TO KEEP IN MIND DURING INSTALLATION AND USE • Do not disassemble the camera on your own. • Always be careful when handling the camera. Do not strike the camera by your fists or shake it. Please be careful not to be careless when storing and operating it. • Do not place or operate the camera in any wet environment such as rain or wet surfaces. •D o not clean the camera with rough sandpaper. Please always use a dry cloth when cleaning it.
SETTING COMMUNICATION PROTOCOL Use number 1~4 PIN of SW702 to set communication Protocol.
BAUD RATE SETTING Use PIN 5 and 6 of SW702. BAUD RATE PIN 5 PIN 6 4800 BPS ON ON 9600 BPS OFF ON 19200 BPS ON OFF 38400 BPS OFF OFF The factory default setting is set to 9600BPS.
SETTING RS-422A/RS-485 TERMINATION Controller Division TX+(DATA+) TX-(DATA-) RX+ n < 32 RX- RX+ CAM 1 RX- RX+ CAM 2 RX- RX- CAM n-1 Termination SW1-ON RX+ CAM n Termination: using numbers 1 and 2 PIN, turn to ON and it will be terminated.
n < 32 Controller Division SW1-ON SW2-ON Division CAM 1 CAM 2 CAM n-1 CAM n Note A communication error may occur if you connect multiple cameras that are assigned the same address in the network.
❚ Adapter cable connection SCC-C6435 Adapter Board ENG 15
❚ Cable connection 1. First, connect one end of the BNC video cable connector to the Video Output Terminal (VIDEO OUT). 2. Then, connect the other end of the connector to the Video Input Terminal of the monitor.
3. Connect the Power Adapter to the Power Cable of the camera. 4. Adjust the switch on the Power Adapter to the proper voltage. Then, connect the Power Adapter's plug to the Power Connector.
5. Connect the Remote Control Terminal of the camera and the external Controller.
❚ Installation precautions 1. Make sure that the installation site can sufficiently support a minimum of four times the net weight of the SCC-C6435(P)/6433(P) SmartDome camera and other accessories. 2. Install in an area where the space above the ceiling board is over 18 cm (7 in.) high. 3. Use the supplied screws to fasten the camera to the bracket assembly. 4. Keep persons away from the installation area, as there is a risk of falling objects. Also, move valuables to a safe location before installation.
2. WALL MOUNT ADAPTOR (SADT-104WM) This adaptor is used for installing the SmartDome camera on an indoor wall. 3. HANGING MOUNT ADAPTOR (SADT-100HM) This adaptor is used for installing the SmartDome camera to an outdoor wall or a ceiling and used with CEILING MOUNT ADAPTOR(SADT-100CM).
4. OUTDOOR HOUSING (SHG-222) This housing is used for installing the SmartDome camera to an outdoor wall or a ceiling. ENG ※ To install and use OUTDOOR HOUSING, remove the Clear Dome from the Camera body before installation. ※ When installing the OUTDOOR HOUSING to an outdoor wall, use WALL MOUNT ADAPTOR (SADT-103WM) to install it.
5. CEILING MOUNT ADAPTOR (SADT-100CM) This adaptor is used for installing the OUTDOOR HOUSING(SHG-222) and HANGING MOUNT ADAPTOR(SADT-100HM) for the SmartDome camera to a concrete ceiling. It is also used for installing the SmartDome camera with HANGING MOUNT ADAPTOR (SADT-100HM) to an indoor wall. 6. POLE MOUNT ADAPTOR (SADT-100PM) This adaptor is used for installing the WALL MOUNT ADAPTOR (SADT-104WM/103WM) to a pole that is over 8 cm (2.76 in.) in diameter.
7. CORNER MOUNT ADAPTOR (SADT-110CM) This adaptor is used for installing the WALL MOUNT ADAPTOR (SADT-104WM/103WM) to the edge of wall.
❚ Installing the camera 1. Install the structure on the ceiling. (Refer to Installation reference for the Length of the structure) * Built in by the builder of the structure 2. Make a hole in the ceiling where the camera will be installed.
3. Assemble the BRACKET-CEILING on the ceiling and screw the 4 bolts in. BRACKET-CEILING ENG 4. Connect the various cables to the CAMERA ADAPTER.
5. Match the BRACKET-CEILING and CAMERA ADAPTER and use 4screws (PH M4 x 8) to assemble them. BRACKET-CELING ASSY-HOLDER CAMERA 6. Pull the safety wire from the case body, and assembly it to the camera holder. SAFETY WIRE SCREW(TH M3XL13.
7. Match the 3 holes on the back of the CAMERA and the CONNECTOR and turn it right about 10 degrees. (Check the sound of LOCKING) * Use the screws (TH M3XL13.8) to connect the CAMERA and the ADAPTER so they don't move. ENG SCREW(TH M3XL13.
Camera Setup CAMERA SET ... VIDEO SET... CAMERA ID OFF/ON... V-SYNC INT/LINE.. DAY/NIGHT DAY.../NIGHT.../AUTO... MOTION DET OFF/ON... ZOOM SPEED 1/2/3/4 DIGITAL ZOOM OFF/X2~X16 DISPLAY ZOOM OFF/ON DISPLAY P/T OFF/ON EXIT QUIT/SAVE/PRESET IRIS ALC.../MANU.../WDR...* SHUTTER OFF/AUTO X2 ~ AUTO X256/1/100 ~ 1/10K AGC OFF/LOW/HIGH MOTION S.SLOW/SLOW/NORM/FAST/ F.
PRESET MAP 0~127 ZONE SET... PRIVACY ZONE OFF/ON... ZONE DIR SET OFF/ON... ZONE AREA SET OFF/ON... EXIT QUIT/SAVE AUTO PAN 1/2/3/4 PATTERN 1/2/3 SCAN 1/2/3/4 AUTO PLAY OFF AUTO SET... 1... ENG PRESET AUTO RETURN OFF/1MIN~12HOUR AUTO PLAY PRESET/SCAN/AUTO PAN/PATTERN PLAY NUMBER 1/2/3/4 2... ALARM SET... ALARM PRIORITY SET... ALARM IN SET... SET TIME ALARM1~8 1~8 EXIT QUIT/SAVE ALARM1~8 NO/NC/OFF EXIT ALARM OUT SET... AUTO SET...
AUX OUT CONTROL... OTHER SET... OUT1 OFF/ON OUT2 OFF/ON OUT3 OFF/ON EXIT QUIT/SAVE PROPORTIONAL P/T OFF/ON TURBO P/T OFF/ON AUTO CAL. OFF/6HOUR/12HOUR/ 18HOUR/24HOUR D-FLIP OFF/ON CAM RESET ... LANGUAGE* CLOCK SET... PASSWORD OFF/ON RS-485 ... EXIT QUIT/SAVE DISPLAY OFF/ON TIME FORMAT 12HOUR/24HOUR SET TIME DATE FORMAT MM/DD/YYYY DD/MM/YYYY YYYY/MM/DD SET DATE EXIT QUIT/SAVE SYSTEM INFO... Note *Selectable languages may vary depending on sales region.
Note - I f the power is turned off after PRESET, AUTO PAN, SCAN, PATTERN function is activated and no other control is made, camera will do the same function after the power is turned on. -W hen tilt position is over 90° and menu-on command is received, pan will automatically rotate 180° and tilt will be move to the corresponding position. Use the controller to press the MENU selection key and the following screen will be displayed.
❚ Camera setup CAMERA ID This CAMERA ID menu is used to assign a camera ID to this camera. If you press the Setup switch when the CAMERA ID menu is selected, the corresponding setup screen appears. (CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT ON... INT DAY... OFF 4 OFF OFF OFF QUIT (CAMERA ID) ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789 : ! - + * () / RET SP ▶▶ ◀◀ SP LOCATION... CAMERA-1...........
(CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT (LL-PHASE) OFF LINE... DAY... OFF 4 OFF OFF OFF QUIT PHASE ( -262) I - - - - RET DAY/NIGHT The DAY/NIGHT menu is used to configure the day and night related settings for this camera. This camera can turn the IR (Infrared) filter on or off. (CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT OFF INT DAY...
DAY... If you press the ENTER when the DAY… submenu is selected, the corresponding screen appears. You can set the values for [C-GAIN] when the DAY… submenu is selected. You can set the values for [AGC COLOR] and [AGC DETAIL] while the AGC menu is selected. (DAY) C-GAIN AGC COLOR AGC DETAIL RET (7) ------- I ( 0) ---- I---(0) I------- Note When the value of AGC DETAIL becomes large, it also makes the noise stand out. NIGHT...
(BW) BURST RET (COLOR) OFF WHITE BAL RET ATW2 ENG Even in night mode, you can see colour images in bright illumination. Therefore you can select any of [COLOR…] and [BW…]. In case of [COLOR…], you have to set the colour temperature for white balance. You can also specify the settings for red and blue colours on your own. In case of [BW...], the burst signals are output with the BW Composite Video signals when the BURST is set to [ON]. And no burst signals are output when the BURST is set to [OFF].
(AUTO) LEVEL DAY NIGHT NIGHT DAY RET ( 0) I-----2S 5S For this function, you can specify the level for each conversion between Day and Night. Note When the DAY/NIGHT is set to [AUTO...], the AGC is displayed with “---“ so you cannot change its setting. MOTION DET The MOTION DET menu is used to configure the motion detection related settings. If you press the ENTER when [ON…] is selected in the MOTION DET menu, the corresponding screen appears.
Those 3 types are like the following: 1. W indow Type The selected area is displayed with a box. The motion can be detected for the area only. You can manually set the motion detection area. You can use the UP/DOWN/LEFT/RIGHT Setup switch to set the size. To move to POSITION, press the switch. After setting the position using the UP/DOWN/ LEFT/RIGHT Setup switch, press the Setup switch to move to the upper menu. To set the size and position for AREA, select any of 0, 1, 2, and 3.
3. Block Type The screen displays with small blocks. When a motion is detected in the selected blocks, the small blocks are displayed on the screen. [PRESET] : The whole screen becomes the motion detection area. [USER...] : You can manually set the motion detection area. Use the UP/DOWN/LEFT/RIGHT, ENTER to set the area. To erase the selected block, press the ENTER. To select [RET], press UP key on the top block or press DOWN key on the bottom block and then press ENTER key to return a upper menu.
ZOOM SPEED In the ZOOM SPEED, menu you can select the speed of the ZOOM Key (Tele/Wide). (CAMERA SET) OFF INT DAY... OFF 4 OFF OFF OFF QUIT ENG CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT Use the Left/Right key in the ZOOM SPEED menu to select the speed. 1: Slowest speed 2: Low speed 3: High speed 4: Fastest speed DIGITAL ZOOM You may set up the digital zoom magnification ratio in the DIGITAL ZOOM menu. The magnification ratio ranges from OFF to 16.
(CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT (CAMERA SET) OFF INT DAY... OFF 4 OFF OFF OFF QUIT CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT OFF INT DAY... OFF 4 X16 OFF OFF QUIT DISPLAY ZOOM In DISPLAY ZOOM, you can display the ZOOM scale on the screen. (CAMERA SET) CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT X032 OFF INT DAY...
DISPLAY P/T In DISPLAY P/T, you can display the position of Pan/Tilt on the screen. (CAMERA SET) 270/090 OFF INT DAY... OFF 4 OFF ON ON QUIT ENG CAMERA ID V-SYNC DAY/NIGHT MOTION DET ZOOM SPEED DIGITAL ZOOM DISPLAY ZOOM DISPLAY P/T EXIT Note - If no change on the Pan/Tilt position is made for 3 seconds, the information window will disappear. - It allows an error range of ± 2˚. EXIT The EXIT menu is used to return to the MAIN menu.
❚ Video set IRIS There is a function to automatically adjust IRIS to the incoming light level. Owing to this function, you may set up the brightness level yourself. The ALC(Auto Light Control) menu allows you for video output level setup. The WDR(Wide Dynamic Range) menu allows you for setting up the level of WDR. Note SCC-C6433(P) does not support for WDR function. MANU Choose the ALC of the IRIS item and press the ENTER and set the submenu to the Video Output level and BLC will be shown.
(ALC) BLC LEVEL RET BOTTOM... ( 0) ---- I---- ENG For items in the BLC menu, the user can set the area and location of the BLC area by pressing ENTER key after put the cursor on [USER…] using the Left, Right key. For AREA items, you can use the Up, Down, Left, Right key to designate the AREA, and then press the ENTER key. You can set the location for areas using the Up, Down, Left, Right key in the [LOCATION]. (ALC) BLC LEVEL RET (BLC) USER... ( 0) ---- I---- ...
(BLC) (BLC) ... RET ... RET Use Left, Right key in the LEVEL menu to control the video output level (brightness). MANU When you press the ENTER key after selecting MANU in the IRIS item, an additional screen appears in which you can set manually opening or closing the IRIS. (VIDEO SET) 44 (MANUAL) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL MANU... OFF HIGH ATW2 ONEAF ...
WDR The WDR camera is a state-of-art technology to expand the screen profit, mostly effective when you photograph both indoor and outdoor. In short, this function provides you with the distinct reproduction of not only the indoor but also the outdoor. Press the ENTER to set up the WDR level. (VIDEO SET) (WDR) WDR... OFF HIGH ATW2 ONEAF ...
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL ALC... OFF HIGH ATW2 ONEAF ... EXIT QUIT Keep pressing both Left and Right in the SHUTTER menu, the speed will change in the following sequence. OFF → AUTO X2 → AUTO X4 → AUTO X6 → AUTO X8 → AUTO X12 → AUTOX16 → AUTO X24 → AUTO X32 → AUTO X48 → AUTO X64 → AUTO X96 → AUTO X128 → AUTO X256 → OFF → 1/120 → 1/250 → 1/500 → 1/1000 → 1/2000 → 1/4000 → 1/10K ※ In case the IRIS mode is set to WDR, only the following modes are available.
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL ALC... OFF HIGH ATW2 ONEAF ... EXIT QUIT ENG Note When the COLOR/BW menu of the camera set is set to [AUTO...], AGC will be displayed as “---“. You can’t adjust the settings manually. MOTION The MOTION function is available only when the SHUTTER menu is set to Slow Shutter AUTO, being composed of 5 steps, [S.SLOW], [SLOW], [NORM], [FAST], [F.FAST]. - [S.
WHITE BAL Lights are generally denoted as colour temperatures and expressed in Kelvin (K) units. The general light colour temperatures are shown below.
- MANU : If WHITE BAL menu is set to MANU mode, the user can set the white Balance considering the current illumination. Select MANU menu and press the ENTER, the sub screen where you can select Manual White Balance will be shown. Use the left/right keys to select 3200K, 5600K or OFF(USER) mode in the PRESET menu. - 3200K : Set colour temperature to 3200K - 5600K : Set colour temperature to 5600K - USER : Choose out a proper value from the RED and BLUE graph for colour and temperature setup.
(VIDEO SET) IRIS SHUTTER AGC WHITE BAL FOCUS MODE SPECIAL ALC... OFF HIGH ATW2 AF ... EXIT QUIT Note ※ AF function may not possible with types of objects listed below. For such objects, focus manually.
DNR DNR(Digital Noise Reduction) function enables the picture to be reduced noise. (SPECIAL) ON OFF OFF (2) -- I(0) I-------(0) I-------+ ENG DNR FLICKERLESS REVERSE DETAIL Y-LEVEL C-LEVEL POSI/NEGA RET FLICKERLESS When this is set to [ON], the shutter speed is set to 1/100 sec (for NTSC) or 1/120 sec (for PAL) to prevent from flickering by the discordance between vertical synchronization frequency and on-and-off frequency of the light.
C-LEVEL It is used to set the levels for the Burst signal and the entire colour signal of the video signal. POSI/NEGA It is used to output as it is, or mirror the video brightness signal. EXIT The EXIT menu is used to return to the MAIN menu. - QUIT : Ignores the changed information and restores the saved information. - SAVE : Saves the information of the setting condition of the menu. - PRESET : I gnores the changed information and restores the initial factory defaults of the menu.
❚ Preset This is the menu that user sets the PAN/TILT location, Zoom/Focus, and screen condition, so the camera can monitor the presetting area on demand. A total of 128 presets are available. ** MAIN MENU ** ENG CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... (PRESET MAP) 0 5 10 15 20 25 30 1 6 11 16 21 26 31 ID: PRESET 0 PRESET NO.
POSITION SET From “POSITION SET...” press the ENTER key to get into the PAN/TILT, FOCUS/ZOOM SET screen to set the PAN/TILT location and FOCUS/ZOOM condition then press the ENTER key to return to a upper menu. PRESET ID This is the ID set up function for each PRESET. It can be set up to 12 characters using the left, right, up, and down keys. The ID location can be set in the submenu of “LOCATION...” VIDEO SET This is the screen setting function for each PRESET.
❚ Zone set ■ The ZONE SET menu includes the setup of PRIVACY ZONE, ZONE DIR SET, and ZONE AREA SET. (ZONE SET) CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... PRIVACY ZONE ZONE DIR SET ZONE AREA SET ON... OFF OFF EXIT QUIT ENG ** MAIN MENU ** PRIVACY ZONE Move PAN/TILT/ZOOM to select an area that can infringe someone privacy, then this function will hide the area if it can be involved in the photograph to protect his privacy.
Note ※ For the safer privacy protection, select about 10 % more than the actual area to hide when you set up the PRIVACY ZONE area. ※ The mosaic of the recorded images is set to be the PRIVACY ZONE. The mosaic of the recorded images can not be recovered after recording. ZONE DIR SET Press the ENTER key in the “ZONE DIR SET ON…” mode to enter the SET NORTH screen MAP. Move PAN to set the NORTH position and press the ENTER key.
ZONE AREA SET Press the ENTER key to enter the ZONE AREA MAP screen from “ZONE AREA SET...”. Select a ZONE AREA number from the ZONE AREA MAP screen and press the ENTER key to enter the ZONE AREA setup screen. (ZONE SET) (ZONE AREA MAP) OFF OFF ON... EXIT QUIT 0 1 2 3 4 5 6 7 ENG PRIVACY ZONE ZONE DIR SET ZONE AREA SET RET ZONE AREA SET0 LOCATION ZONE ID SET ZONE ENABLE ... ...
LOCATION The [LOCATION...] menu designates the left/right LIMIT positions of ZONE AREA. Enter the setup screen to move PAN, then select a start position and press the ENTER key. Move PAN again to select an end position and press the ENTER key. Now, ZONE AREA setup is complete. SET START! ZONE AREA SET0 LOCATION ZONE ID SET ZONE ENABLE ... ...
ZONE ID SET This function is used to allocate as many as 12 IDs to each zone area. Use Left/Right/ UP/DOWN for this purpose. You may select the ID position from the additional menu of [LOCATION...]. ZONE AREA SET0 ... ... ON EXIT QUIT ZONE AREA ID 0 ABCDEFGHIJKLMNOPQRSTUVWXYZ 0123456789 : ! - + * () / ENG LOCATION ZONE ID SET ZONE ENABLE RET SP▶▶ ◀◀SP LOCATION... ZONE. 0...... ZONE ENABLE This function turns [ON] or [OFF] the ZONE AREA ID indication.
❚ Auto set The AUTO SET menu includes AUTO PAN, PATTERN, and SCAN and it is able to set up the AUTO PLAY motion. AUTO PAN After selecting the locations of two points (PAN/TILT) of START and END, it loops continuously in the set up SPEED. The number of AUTO PAN is up to 4. ** MAIN MENU ** (AUTO SET) CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO...
POSITION SET The menu [POSITION SET …] sets the Start / End position of AUTO PAN. Return to the settings screen and set the desired START position for PAN/TILT, and then press the ENTER key. And, set the END position for the PAN/TILT. Press the ENTER key to finish the setup for AUTO PAN Start/End positions.
PATTERN This is a replay function so that the MANUAL functions such as PAN, TILT, ZOOM, and FOCUS are played for 2 minutes. Note - When the PATTERN is saved/executed, the PAN/TILT is operated with PROPORTIONAL ON, TURBO OFF. - If the SSC-1000 or SSC-2000 is used when uploading/downloading the menu setup, reset the PATTERN because it may be different with the first setting.
PATTERN can be set up to 3. Choose 1, 2, or 3 with the Left/Right key in the [PATTERN SET] and press the ENTER key to get into the PATTERN set up screen. From the moment “PATTERN SET 1” is gone for 2 minutes, it memorizes the MANUAL movements and after 2 minutes, it will return to a upper menu. If you want to finish set up before the 2-minutes ends, press the ENTER key. SCAN SCAN sets the direction of PRESET movement during SCAN operation. The number of SCAN is up to 4.
AUTO PLAY If you press the ENTER switch when the [1…] submenu is selected, the corresponding screen appears. (AUTO PLAY SET) (AUTO SET) AUTO PAN PATTERN SCAN AUTO PLAY 1 2 1 2 1 2 1... RET QUIT 3 3 3 4 4 AUTO RETURN AUTO PLAY PLAY NUMBER OFF PRESET 0 EXIT QUIT AUTO RETURN This menu sets up the time during which AUTO PLAY repeats. AUTO PLAY This function sets up the motion which will be repeatedly performed by the camera whenever the time set by AUTO RETURN elapses.
If you press the ENTER switch when the [2…] submenu is selected, the corresponding screen appears. (AUTO SET) 1 2 1 2 1 2 2... RET QUIT 3 3 3 4 4 (SET TIME) ID START END 1 00:00 03:00 2 03:00 06:00 3 06:00 09:00 4 09:00 12:00 5 12:00 15:00 6 15:00 18:00 7 18:00 21:00 8 21:00 24:00 EXIT PLAY OFF OFF OFF OFF OFF OFF OFF OFF QUIT NO. - ENG AUTO PAN PATTERN SCAN AUTO PLAY Set the start/end time and select PRESET, PATTERN, AUTO PAN or SCAN to set up.
ALARM PRIORITY SET This sets the priority of the 8 ALARM inputs so ALARM can work corresponding to the priority. The priority of the DEFAULT is ALARM1, ALARM2, ALARM3, ALARM4, ALARM5, ALARM6, ALARM7, ALARM8. If the ALARM is working at the same time and the priority is the same, it will operate according to the DEFAULT priority. While the ALARM is working, it cannot detect MOTION.
❚ Other set (OTHER SET) CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... PROPORTIONAL P/T TURBO P/T AUTO CAL. D-FLIP CAM RESET LANGUAGE PASSWORD RS-485 EXIT ON OFF OFF OFF ... ENGLISH OFF ... QUIT ENG ** MAIN MENU ** PROPORTIONAL P/T This function controls the PAN/TILT speed to the ZOOM magnification ratio during the manual operation of PAN/TILT.
D-FLIP When D-FLIP is off, TILT movement ranges from 0° to 90°. When D-FLIP is on, TILT movement ranges from 0° to 180°. When D-FLIP is on, images mirror vertically and horizontally in the area beyond TILT 90°. CAM RESET CAM RESET clears all the settings made so far and restores the factory default settings. [CAMERA RESET?] message appears when you select CAM RESET. Select [CANCEL] to return to the menu setup display or select OK to restore the factory default settings.
PASSWORD This function selects or cancels the MENU setup password. Press the ENTER key at the state of PASSWORD ON, and the following screen will appear for password setup. (OTHER SET) (PASSWORD) OFF OFF OFF OFF ... ENGLISH ON... ... QUIT 0 1 2 3 4 5 6 7 8 9 **** RET ENG PROPORTIONAL P/T TURBO P/T AUTO CAL. D-FLIP CAM RESET LANGUAGE PASSWORD RS-485 EXIT **** Press Up/Down/Left/Right key to locate the cursor on a number and press the ENTER key for password setup.
RS-485 (OTHER SET) PROPORTIONAL P/T TURBO P/T AUTO CAL. D-FLIP CAM RESET LANGUAGE PASSWORD RS-485 EXIT (RS-485) OFF OFF OFF OFF ... ENGLISH ON... ... QUIT PRIORITY PROTOCOL BAUD RATE ADDRESS RET HW SAMSUNG HALF 9600 0 [PRIORITY] menu is used to set the priority between hardware and software. If you select [HW], it operates according to the value of the camera hold adapter. If you select [SW], you can manually set [PROTOCOL], [BAUD RATE], [ADDRESS] for RS-485.
❚ System info This menu allows you to check S/W version, communication protocol, baud rate, and address of the camera. ** MAIN MENU ** (SYSTEM INFO) ALARM VER. MOTOR VER. CAMERA VER. EEPROM VER. PROTOCOL COMM. TYPE BAUD RATE ADDRESS SERIAL NO. RET 1.000 1.000 1.000 1.000 SAMSUNG RS-485, HALF 9600 0 000000000000000 ENG CAMERA SET... VIDEO SET... PRESET... ZONE SET... AUTO SET... ALARM SET... OTHER SET... CLOCK SET... SYSTEM INFO... * ALARM, MOTOR, CAMERA and EEPROM VER. may change without notice.
❚ Shortcut keys SSC-1000 or SSC-2000 Controller supports the following short keys.
Function Key AUTO RETURN *1) [PRESET] + [1] + [4] + [8] + [Enter] AUTO Calibration [PRESET] + [1] + [4] + [9] + [Enter] CAM RESET [PRESET] + [1] + [5] + [0] + [Enter] Other keys than AUTO CAL. and AUTO RETURN, upon execution, shall be applied to the MENU setup process. ENG *1) The use of AUTO RETURN will be available only when the function equivalent to AUTO PLAY, a sub menu of AUTO SET has been built in.
SCC-6435 FRONT 74 BACK
Product Specifications Item Product Type Power Input Power Consumption Broadcasting Type SCC-C6433/C6435 : AC 24V ± 10% (60Hz ± 0.3Hz) SCC-C6433P/C6435P : AC 24V ± 10% (50Hz ± 0.
Item 76 Details Min. Scene illumination Condition Illumination Sens-up 50IRE Off 30IRE Off 15IRE Off 50IRE x256 30IRE x256 15IRE x256 SCC-C6433(P) Colour B/W 2.0 0.20 1.2 0.12 0.6 0.06 0.008 0.0008 0.005 0.0005 0.002 0.0002 SCC-C6435(P) Colour B/W 1.2 0.12 0.7 0.07 0.3 0.03 0.005 0.0005 0.003 0.0003 0.001 0.0001 WDR SCC-C6433/C6433P : N/A SCC-C6435 : x128 SCC-C6435P : x160 Signal Output COMPOSITE VIDEO OUT : 1.0 Vp-p 75 ohms/BNC Lens One body; 32x Zoom lens Focal length : 3.
Item Details -10°C ~ +50°C Operation Humidity ~90% SIZE DOME : 147.65(ø), Outline : 177(ø) x 194.
Memo
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.