Thank you for buying a Samsung Camera. This manual will guide you through using the Digimax 101, including taking images, downloading images and using the MGI PhotoSuite III SE software. Please read this manual before using your new camera.
INSTRUCTIONS Use this camera in the following order. If your video output signal is PAL type, you have to select [PAL/50Hz] in [VIDEO OUT] menu before taking a picture.(p.77) Set up the camera driver Take a picture Insert USB cable 2 Before connecting the USB cable to the PC and this camera, you have to set up the camera driver. Install the camera driver that is contained in the Application S/W CD-ROM. (p.91) Take a picture (p.
SPECIAL FEATURES READY This digital camera has the following features. A fine resolution of 1.3 mega pixels 2 X digital zoom lens Movie clip recording function Date imprinting on a still image Multiple language support An FCC warning This device has been tested in accordance with the limits of a class B digital device under item 15 of the FCC rules. These limits are designed to provide protection against harmful interference in commercial installation.
CONTENTS Ready Getting to know your camera 6 Safety note 7 This digital camera can be used for 10 Manufacturer s contents 12 Identification of features 13 Product Exterior(Front / Top / Side) 13 Product Exterior (Back/bottom) 14 Viewfinder/Camera status LED 15 LCD monitor indicator 16 Camera mode definition 18 STILL IMAGE mode 18 MOVIE CLIP mode 18 PLAY mode 18 PC mode 18 SETUP mode 18 Selecting camera mode and menu 19 LCD monitor menu indicator 20 Preparation 26 Connecting to Power 26 Using the batteries 2
CONTENTS MODE button 54 MENU button 54 5-function button 55 OK button 56 UP button 57 DOWN button 58 LEFT button 59 RIGHT button 59 Setting up the play back function using the LCD monitor 60 SLIDE SHOW 60 PROTECT 61 DELETE ALL 62 COPY TO CARD 63 DPOF 65 LCD BRIGHTNESS 67 Setting up the camera system 68 Starting SETUP mode 68 BEEP 69 FORMAT 70 POWER OFF 71 RESET 72 DATE SETUP 73 DATE IMPRINT 74 DATE TYPE 75 LANGUAGE 76 VIDEO OUT 77 PC mode 79 Starting PC mode 79 Important notes 81 Caution! 81 Warning indica
GETTING TO KNOW YOUR CAMERA Thank you for buying a Samsung Digital Camera. Prior to using this camera, please read the user manual thoroughly. Keep the manual in a safe place. About the symbols This manual contains instructions on using this camera that will help you to use this camera safely and correctly. This will help prevent danger and injury to others. DANGER DANGER indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
SAFETY NOTE READY DANGER Do not attempt to modify this camera in any way. This may result in fire, injury, electric shock or severe damage to you or your camera. Internal inspection, maintenance and repairs should be carried out by your dealer or Samsung Camera Service Center. Please do not use this product in close proximity to flammable or explosive gases, as this could increase the risk of explosion. Should any form of liquid or a foreign object enter the camera, do not use it.
SAFETY NOTE WARNING Do not use the flash in close proximity to people or animals. Positioning the flash too close to your subject s eyes, may cause eyesight damage. When taking photographs, never point the lens of the camera directly into very strong light. This may result in permanent damage to the camera or your eyesight. For safety reasons keep this product and accessories out of reach of children or animals to prevent accidents e.g.: Swallowing batteries or small camera accessories.
SAFETY NOTE READY CAUTION Leaking, overheating, or burst batteries could result in fire or injury. Use batteries with the correct specification for the camera. Do not short circuit, heat or dispose of batteries in fire. Do not use old batteries with new ones, or mix brands of batteries. Ensure the batteries are positioned correctly with regard to polarity (+ / -). When the camera is not in use for long periods, always unplug the camera from its power source.
THIS DIGITAL CAMERA CAN BE USED FOR Viewing images on TV (refer to page 77) Printing images using a dedicated printer, DPOF-compatible printer or DPOF-equipped photo lab. (refer to page 65) Taking a picture. (refer to page 33 ~ 49) Down loading image files from camera to computer.
THIS DIGITAL CAMERA CAN BE USED FOR READY Creation of a digital photo album Inserting images directly into any electronic document Taking a self-portrait and using the image to personalize name cards You can even create your own unique gift-wrap paper by using your digital images 11
MANUFACTURER S CONTENTS Manufacturer's contents Please check that you have the correct contents before using this product.
IDENTIFICATION OF FEATURES READY Product Exterior(Front / Top / Side) Power switch Shutter button Self-timer lamp Viewfinder Flash(p.
IDENTIFICATION OF FEATURES Product Exterior (Back/bottom) Viewfinder LCD button (p.35 / 53) Camera status LED (p.15) MODE button (p.36 / 54) MENU button (p.37 / 54) LCD monitor 5-function button (p.37 / 55) Tripod socket THUMBNAIL / UP( ) button (p.39 / 57) FLASH/ LEFT( ) button (p.39 / 59) SELF-TIMER/ RIGHT( ) button (p.41 / 59) OK button (p.38 / 56) DELETE / DOWN( ) button (p.
IDENTIFICATION OF FEATURES READY Viewfinder/Camera status LED Camera status LED Picture area frame Optimum picture area over 1.5m Camera status LED Color Status On Camera status Image processing(compression/decompression) USB busy(PC mode) Red Flash charge processing Blinking On & blinking Green USB busy Power on processing On Idle power mode (after 60sec.
IDENTIFICATION OF FEATURES LCD monitor indicator The LCD monitor displays information about the shooting conditions. Recording mode Image & Full Status No. 16 Description Icons Page 1 Battery p.26 2 Camera shake warning p.34 3 Flash 4 Self-timer 5 White balance 6 Exposure compensation 7 Date 2002/09/01 8 Time 03:15 9 Card indicator p.39~40 p.41 p.47 +0.5 EV (Exposure Value) p.45 p.
IDENTIFICATION OF FEATURES Description Icons Page 10 Quality p.44 11 Image size p.43 Number of available shots remaining(still image) 0015 Recording time(while recording a movie clip) 00:50 READY No. 12 13 Message for canceling a movie clip recording 14 Digital zoom 15 Recording mode p.38 Play mode Image & Basic Status No. Description 1 Battery 2 Recording date 3 Card indicator 4 Number of stored images Icons Page p.26 2002/09/01 p.29 100-0003 p.
IDENTIFICATION OF FEATURES Camera mode definition You can select the desired working mode by using the mode button located on the back of the camera. This digital camera has 5 working modes. These are listed below STILL IMAGE mode ( ) (p.33) This mode is used for still image shots between 1m ~ infinity. MOVIE CLIP mode ( ) (p.33) A movie clip can be recorded as long as the available recording time allows. PLAY mode (p.
IDENTIFICATION OF FEATURES READY Selecting camera mode and menu You can select a camera mode or a camera mode menu by pressing the MODE button or MENU button as below.
IDENTIFICATION OF FEATURES LCD monitor menu indicator Each mode has a menu as shown below. * marked sub menu is the default setting. Camera mode Main menu STILL IMAGE 1/2 ( Sub menu ) SETUP IMAGE SIZE (p.68) 1280X1024* (p.43) 640X512 QUALITY SUPER FINE (p.44) FINE* NORMAL EXPOSURE 20 -2.0 ~ 0.0* ~ +2.0EV (0.5EV steps) (p.
IDENTIFICATION OF FEATURES Main menu STILL IMAGE 2/2 ( READY Camera mode Sub menu ) WHITE BALANCE AUTO* (p.47) DAYLIGHT CLOUDY SUNSET TUNGSTEN FLUORESCENT QUICK VIEW ON* (p.48) OFF LCD BRIGHTNESS -5~0*~+5 (p.
IDENTIFICATION OF FEATURES Camera mode MOVIE CLIP ( Main menu Sub menu ) SETUP (p.68) EXPOSURE -2.0 ~ 0.0* ~ +2.0EV (0.5EV steps) WHITE BALANCE AUTO* (p.47) DAYLIGHT CLOUDY SUNSET TUNGSTEN FLUORESCENT LCD BRIGHTNESS 22 -5~0*~+5 (p.49) (p.
IDENTIFICATION OF FEATURES PLAY 1/2 ( Main menu READY Camera mode Sub menu ) SETUP (p.68) SLIDE SHOW 1, 3*, 5, 7, 9sec PROTECT ONE IMAGE* (p.60) LOCK (p.61) UNLOCK* ALL IMAGE LOCK UNLOCK* DELETE ALL YES (p.62) NO PLAY 2/2 ( ) COPY TO CARD YES (p.63) NO DPOF # OF PRINTS LCD BRIGHTNESS -5~0*~+5 (p.65) (p.
IDENTIFICATION OF FEATURES Camera mode SETUP 1/3 Main menu BEEP Sub menu ON* (p.69) OFF FORMAT YES (p.70) NO POWER OFF 3min*/5min/10min/30min/CANCEL RESET YES (p.72) NO SETUP 2/3 DATE SETUP 2002/01/01 ~ 2099/12/31 DATE IMPRINT YES* (p.74) NO DATE TYPE YYYY/MM/DD* DD/MM/YYYY MM/DD/YYYY 24 (p.75) (p.73) (p.
IDENTIFICATION OF FEATURES SETUP 2/3 Main menu LANGUAGE READY Camera mode Sub menu ENGLISH (p.76) FRANÇAIS DEUTSCH ESPAÑOL ITALIANO ? ??? @?e?@g? @?e?@g? ?J5?e?@g? ?7H?e?@g? J@e@@@@@@@@e? 7@f@@@?f? ?J@@f@@@Lf? ?7Y@f@@V1f? ?@?@e?J@@?3L?e? ?@eW.Y@?V/Xe? ?@?W.YJ@eV/X?? ?@?.Y?@@@@?V/?? ?@fN@g? ?@f?@g? ?@f?@g? ? SETUP 3/3 VIDEO OUT NTSC/60Hz (p.
PREPARATION Connecting to Power There are two ways in which to provide the camera with power. You can use batteries(AA Alkaline, NiMH, CR-V3), or alternatively, you can use an AC Adapter (DC 3.3V 2.0A). Using the batteries 1. Open the battery chamber cover by pushing in the direction of the arrow. 2. Insert the batteries taking note of the polarity (+ / -). 3. To close the battery chamber cover, push it until it clicks.
PREPARATION READY INFORMATION This camera will automatically switch off when not in use for a period of time. Refer to [POWER OFF] function(p.71). NOTICE Important information about battery usage Please remove the batteries if the camera will not be used for long periods. Batteries can lose power over time and are prone to leaking if kept inside the camera. We recommend high capacity ALKALINE batteries as manganese batteries cannot deliver sufficient power.
PREPARATION Using the AC power adapter If you have access to a mains supply, using an AC Adapter allows the camera to be used for long periods of time. If you connect the camera to a computer, it is advisable to use an AC adapter, as this will enable extended use. Plug the adapter into the connection point (DC IN 3.3V) on the camera. DANGER/ NOTICE Always turn off the power before taking the AC adapter out of the mains supply. As with all mains powered devices, safety is important.
PREPARATION READY Inserting the SD memory CARD The camera comes with 8MB of internal flash memory, allowing you to store images and movie clips in the camera. However, you can expand the memory capacity by using an optional SD memory card([CARD] stands for the SD memory card) so that you can store more images and movie clips. 1. Turn off the camera power and pull the card cover in the direction of the arrow to open. 2. Insert the card all the way into the card slot.
PREPARATION The CARD has a write protect switch that prevents image files from being deleted or formatted. By sliding the switch to the bottom of the card, the data will be protected. By sliding the switch to the top of the card, the data protection will be canceled. Check the switch position before taking an image. Card pins Write protect switch Label SD(Secure Digital) memory card Removing the SD memory card 1. Turn the power off using the power switch ( ). 2.
PREPARATION READY Instructions on how to use the SD memory card Using a new CARD for the first time Before using the CARD, it must be initialized. When you format the card in your PC, you have to select FAT file system.(p.66) [FORMAT] prepares the memory for recording data. Refer to page 70 for information on [FORMAT]. Memory capacity When using the internal memory, the specified shooting capacity will be as follows.
PREPARATION Do not store the CARD in an environment with strong electronic or magnetic fields, e.g. near loud speakers or TV receivers. Please do not use or store in an environment where there are extremes in temperature. Do not allow the CARD to become dirty or to come into contact with any liquid. Should this happen, clean the card with a soft cloth. Please keep the CARD in its case when not in use. During and after periods of extended use, you may notice that the CARD is warm. This is perfectly normal.
RECORDING MODE Starting Recording Mode If the CARD is inserted in the camera, all the camera functions are applied only to the CARD. If the CARD is not inserted in the camera, all the camera functions are applied only to the internal memory. If your video output signal is PAL type, you have to select [PAL/50Hz] in [VIDEO OUT] menu before taking a picture.(p.77) Recording a still image ADVANCED 1. Insert the batteries (p.26). Insert the batteries taking note of the polarity (+ / -). 2. Insert the CARD (p.
RECORDING MODE NOTICE Camera shake warning. When the Flash Off mode is selected, the camera shake warning indicator ( ) may appear on the LCD monitor. In this case, use a tripod, support the camera on a solid surface or change the flash mode to flash shot mode. Backlight compensated shot When taking an outdoor shot, avoid facing the sun, as the image may be dark because of the strong backlight. In backlight conditions, please use exposure compensation (refer to page 45).
RECORDING MODE Using the camera button to adjust the camera The STILL IMAGE/MOVIE CLIP mode function can be set up by using the camera button. POWER switch ADVANCED Used for turning the camera power on / off. If this camera doesn t be operated during the specified time(about 60 SEC.), the camera power will be idle(LCD monitor off, Camera status LED : Green) automatically(p.71). To use the camera again, press the camera buttons except the power switch.
RECORDING MODE Pressing the LCD button image & full information Pressing the LCD button image & basic information Pressing the LCD button LCD off MODE button Pressing the MODE button in the RECORDING(STILL IMAGE, MOVIE CLIP) mode will change the display as shown below.
RECORDING MODE MENU button When you press the MENU button, a menu related to each camera mode will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display.
RECORDING MODE OK button When the menu is displayed on the LCD monitor, the OK button is used for confirming data that is changed by using ( / / / ) buttons. When the menu is not displayed on the LCD monitor, pressing the OK button activates digital zooming in(2X). The maximum zoom magnification is 2X for recording and viewing images. Digital zoom To use the digital zoom the LCD monitor has to be turned on. 1. Turn the camera power on. 2.
RECORDING MODE UP( ) button When the menu is displayed on the LCD monitor, pressing the UP button ( ) makes the menu cursor move up. DOWN( ) button When the menu is displayed on the LCD monitor, pressing the DOWN( ) button makes the menu cursor move down. ADVANCED FLASH( )/ LEFT( ) button When the menu is displayed on the LCD monitor, the LEFT ( ) button makes the sub menu data change. When the menu is not displayed on the LCD monitor, the LEFT ( ) button operates as the FLASH button ( ).
RECORDING MODE Flash mode indicator FLASH MODE Auto flash Indicator Definition If the subject or background is dark, the camera flash will operate automatically. If a subject or background is dark, the camera flash will work automatically and will reduce the red-eye effect by using the redeye reduction function. Auto & Red eye reduction Flash off The flash does not fire. Select this mode when capturing images at a place where flash photography is prohibited.
RECORDING MODE SELF-TIMER( ) / RIGHT( ) button When the menu is displayed on the LCD monitor, the RIGHT ( ) button makes the sub menu data change. When the menu is not displayed on the LCD monitor, the LEFT ( ) button operates as the SELF-TIMER button ( ). This function is used when the photographer would also like to be in the image. ADVANCED Selecting the self-timer The self-timer activates only in RECORDING (STILL IMAGE/ MOVIE CLIP) mode. Use a tripod or place the camera on a stable surface. 1.
RECORDING MODE Using the LCD monitor to adjust the camera Recording functions can be changed by using the LCD monitor. In the RECORDING(STILL IMAGE/MOVIE CLIP) mode, pressing the MENU button displays the menu on the LCD monitor. The following functions are available, depending on the mode you have selected (STILL IMAGE, MOVIE CLIP ). STILL IMAGE mode MOVIE CLIP mode PAGE IMAGE SIZE O X p.43 IMAGE QUALITY O X p.44 EV COMPENSATION O O p.45 WHITE BALANCE O O p.47 QUICK VIEW O X p.
RECORDING MODE IMAGE SIZE In STILL IMAGE mode, you can select the image size you require. A large image uses more memory, so increasing the image size will reduce the total number of shots you can store in the memory. The image sizes are listed below. ADVANCED Selecting the image size 1. Turn the camera power on. 2. Press the MENU button to display the STILL IMAGE mode menu on the LCD monitor. 3. Press the UP( )/ DOWN( ) button and select [IMAGE SIZE]. 4.
RECORDING MODE IMAGE QUALITY In STILL IMAGE mode, you can select the image quality(Data compression rate). The higher the QUALITY setting, the better the final image will be. However, the high quality setting will require more memory and therefore reduce the number of images you can store on the memory. SUPER FINE is the highest quality and NORMAL is the lowest setting. Choose the setting appropriate for your needs. The image sizes are listed below. SUPER FINE FINE Selecting the image quality 1.
RECORDING MODE EV COMPENSATION In STILL IMAGE/MOVIE CLIP mode, you can select the exposure value. This camera automatically adjusts the exposure according to the ambient lighting conditions. However, you can select the exposure value by using the [EXPOSURE] sub menu. Exposure compensation setting range : -2.0 ~ +2.0 EV (0.5 EV steps) If you increase the exposure value, the image will be brighter. If you decrease the exposure value, the image will be darker. 1. Turn the camera power on. 2.
RECORDING MODE INFORMATION This change to the exposure will remain until the camera is switched off. When the camera is turned on again, the exposure compensation setting returns to 0.0EV (discarding the exposure compensation). When you have selected a change in exposure value, the value is displayed on the LCD. Decreasing or increasing the exposure value may lead to images being under or over exposed (too dark or too bright).
RECORDING MODE WHITE BALANCE In STILL IMAGE/MOVIE CLIP mode, you can select the white balance menu. Different lighting conditions may cause a color cast on your images. The white balance control allows you to adjust the colors to appear more natural looking. There are 6 white balance menus : AUTO/ DAYLIGHT/ CLOUDY/ SUNSET/ TUNGSTEN/ FLUORESCENT Selecting the white balance STILL IMAGE 2/2 ADVANCED 1. Turn the camera power on. 2. Select STILL IMAGE or MOVIE CLIP mode by pressing the MODE button. 3.
RECORDING MODE INFORMATION AUTO : The camera automatically selects the appropriate white balance settings, depending on the prevailing lighting conditions. DAYLIGHT : For taking images outside on a bright day CLOUDY : For taking images under a cloudy and overcast sky. SUNSET : For taking images at sunset FLUORESCENT : For taking images under fluorescent lighting TUNGSTEN : For taking images under tungsten (standard light bulb) lighting. QUICK VIEW In STILL IMAGE mode, you can select the quick view menu.
RECORDING MODE LCD BRIGHTNESS In STILL IMAGE/MOVIE CLIP mode, you can select the LCD brightness menu. You may adjust the LCD brightness. Brightness range : -5 ~ 0 ~ +5 Selecting the LCD brightness STILL IMAGE 2/2 WHITE BALANCE ADVANCED 1. Turn the camera power on. 2. Select STILL IMAGE or MOVIE CLIP mode by pressing the MODE button. 3. Press the MENU button to display the STILL IMAGE/MOVIE CLIP mode menu on the LCD monitor. 4.
PLAY MODE Starting Play Mode Turn the camera on and select the PLAY mode by pressing the MODE button. The camera can now play back the images stored on a memory. You can set up the PLAY mode function by using the camera buttons and LCD monitor. Playing back a still image 1. Slide the power switch to turn on the camera. 2. Select the PLAY mode by pressing the MODE button. 3. The last image stored on the memory is displayed on the LCD monitor. 4.
PLAY MODE Playing back a movie clip Steps from 1-3 are the same as those to play back a still image. 4. Select the movie clip that you want to play back by using the LEFT( )/RIGHT( ) button. If you select a movie clip file, the movie clip indicator( ) will be displayed on the LCD monitor. 5. Press the OK button to play back a movie clip - To pause playing back a movie clip, press the OK button again. - Press the OK button and the movie clip will restart.
PLAY MODE NOTICE If there are no images stored on the internal memory or SD memory card, a [NO IMAGE] message will be displayed on the LCD monitor. INFORMATION If the CARD is inserted in the camera, all the camera functions are applied only to the CARD. If the CARD is not inserted in the camera, all the camera functions are applied only to the internal memory. The last image stored on the internal memory will be displayed on the LCD monitor.
PLAY MODE Setting up the play back function by using the camera button You can set up the PLAY mode function by using the camera buttons. Power switch Used for turning the camera power on / off. If this camera doesn't be operated during the specified time(about 60 SEC.), the camera power will be idle(LCD monitor off, Camera status LED : Green) automatically(p.71). To use the camera again, The camera power will be turned off automatically during periods of inactivity. This is done to reduce battery drain.
PLAY MODE MODE button Pressing the MODE button in PLAY mode will change the display as shown below. Pressing the MODE button PLAY mode Pressing the MODE button STILL IMAGE mode Pressing the MODE button MOVIE CLIP mode MENU button When you press the MENU button, a menu related to each camera mode will be displayed on the LCD monitor. Pressing it again will return the LCD to the initial display.
PLAY MODE 5-function button Explanation of the 5-function button BUTTON MENU DISPLAY ON NOTICE Starts the thumbnail display mode OFF Selects a up image(Thumbnail display) ON Makes the menu cursor move down Page 57 ADVANCED UP( ) button PLAY mode Makes the menu cursor move up Moves to the upper part of the image(Digital zoom) Deletes a displayed image DOWN( ) button Selects a down image(Thumbnail display) Page 58 Moves to the lower part of the image(Digital zoom) ON LEFT( ) button Changes
PLAY MODE OK button When the menu is displayed on the LCD monitor, the OK button is used for confirming data that is changed by using the / / / buttons. When the menu is not displayed on the LCD monitor, pressing the OK button activates the following. - Normal display : Whenever you press the OK button, a still image will be enlarged to a 2X scale of enlargement. - Thumbnail display : The thumbnail display is changed to Normal display by pressing the OK button.
PLAY MODE UP( ) button When the menu is displayed on the LCD monitor, pressing the UP button ( ) makes the menu cursor move up. When the menu is not displayed on the LCD monitor, pressing the UP( ) button activates the following. - Normal display : Starts / stops the thumbnail display - Thumbnail display : Selects a up image - Digital zoom : Moves to the upper part of the image ADVANCED Thumbnail display 1. Press the UP( ) button in the PLAY mode. 2.
PLAY MODE DOWN( ) button When the menu is displayed on the LCD monitor, pressing the DOWN button ( ) makes the menu cursor move down. When the menu is not displayed on the LCD monitor, pressing the DOWN( ) button activates the following. - Normal display : Deletes a displayed image - Thumbnail display : Selects a down image - Digital zoom : Moves to the lower part of the image Deleting an image A protected image can t be deleted. 1.
PLAY MODE LEFT( ) button When the menu is displayed on the LCD monitor, the LEFT ( ) button makes the sub menu data change. When the menu is not displayed on the LCD monitor, pressing the LEFT( ) button activates the following. - Normal / Thumbnail display : Moves to previous image - Digital zoom : Moves to the left part of the image ) button When the menu is displayed on the LCD monitor, the RIGHT ( ) button makes the sub menu data change.
PLAY MODE Setting up the play back function using the LCD monitor PLAY mode functions can be changed by using the LCD monitor. In the PLAY mode, pressing the MENU button displays the menu on the LCD monitor. SLIDE SHOW Images can be displayed continuously at pre-set intervals. This is useful and convenient for checking recorded images and for presentations. You can select the slide show play back time(1sec/ 3sec/ 5sec/ 7sec/ 9sec) Starting the slide show PLAY 1/2 1. Turn the camera power on. SETUP 2.
PLAY MODE PROTECT This is used to protect specific shots from accidental erasing (LOCK). It also releases images that have been previously protected (UNLOCK). Protecting images PLAY 1/2 If you protect an image, the protect icon( SETUP SLIDE SHOW ADVANCED 1. Turn the camera power on. 2. Press the MODE button to select the PLAY mode 3. Select an image that you want to protect by pressing the LEFT( )/ RIGHT( ) button. 4. Press the MENU button to display the PLAY mode menu on the LCD monitor. 5.
PLAY MODE DELETE ALL This enables you to clear all unprotected images from the memory. To delete the images or movie clips stored in the internal memory, remember not to insert the SD memory card in the camera. Otherwise, you will delete the image or movie clip stored in the SD memory card. Deleting all images PLAY 1/2 Remove the SD memory card to delete images that are in SETUP the internal memory. SLIDE SHOW Insert the SD memory card to delete images that are in PROTECT the SD memory card. 1.
PLAY MODE COPY TO CARD This enables you to copy image files to the CARD. Copying image files to the CARD PLAY 2/2 1. Insert a card. COPY TO CARD 2. Turn the camera power on. 3. Press the MODE button to select the PLAY mode. If you insert a card that hasn t an image, [NO IMAGE!] DPOF LCD BRIGHTNESS on the LCD monitor. YES ADVANCED message will display. But it isn t camera malfunction. 4. Press the MENU button to display the PLAY mode menu NO 5.
PLAY MODE The number of the stored image in the PLAY mode - The number of the stored image in the PLAY mode will be displayed as shown below. 100 - 0003 100 0003 : the SSCAM folder number : the stored image number The image is stored on the 100SSCAM sub folder that is created under the DCIM folder in the internal or memory card(SD memory card / Multi Media Card).
PLAY MODE DPOF DPOF(Digital Print Order Format) allows you to embed printing information on your memory card. Select the pictures to be printed and how many prints to make. Images can then be printed on DPOF printers, or at an increasing number of photo laboratories. This function is not available for Movie clips. The DPOF file is only stored on the card. To make a DPOF file for the images that are stored on the internal memory, apply the [COPY TO CARD](p.63) function first. ADVANCED Setting up DPOF 1.
PLAY MODE DPOF # OF PRINTS 8. Select the desired number of prints by pressing the LEFT( )/RIGHT( ) button. 9. Press the Ok button to confirm the setting. 1 NOTICE When you format the card in your PC that runs on Windows 2000 or XP, please select FAT file system. If you select FAT 32, the image file may not be recognized on DPOF printer. Formatting on a PC 1. Select [Removable Disk] in the [Windows Explorer] 66 2. Press the right mouse button and select [Format]. 3.
PLAY MODE INFORMATION The DPOF indicator( ) will display on the LCD monitor when an image that has DPOF information plays back. LCD BRIGHTNESS You may adjust the LCD brightness. 1. Turn the camera power on. 2. Press the MODE button to select the PLAY mode. 3. Press the MENU button to display the PLAY mode menu on the LCD monitor. 4. To shift menu cursor to [PLAY 2/2], press the DOWN( ) button at the [DELETE ALL] menu that is in [PLAY 1/2]. 5. Press UP( ) /DOWN( ) and select [LCD BRIGHTNESS]. 6.
SETTING UP THE CAMERA SYSTEM Starting SETUP mode You can select the SETUP mode in the STILL IMAGE/ MOVIE CLIP/ PLAY mode menu. STILL IMAGE 1/2 MOVIE CLIP PLAY 1/2 SETUP SETUP SETUP IMAGE SIZE EXPOSURE SLIDE SHOW QUALITY WHITE BALANCE PROTECT EXPOSURE LCD BRIGHTNESS DELETE ALL STILL IMAGE mode MOVIE CLIP mode Selecting the SETUP mode 1. Turn the camera power on. 2. Press the MODE button to select the STILL IMAGE/ MOVIE CLIP/ PLAY mode. 3. Press the MENU button. 4.
SETTING UP THE CAMERA SYSTEM BEEP A beep will sound when you press the camera button and an error takes place. You can check the camera condition by this function. Selecting the beep sound SETUP 1/3 BEEP FORMAT POWER OFF ADVANCED Steps 1 to 5 are the same as those for selecting the SETUP mode.(p.68) 6. Press UP( ) /DOWN( ) and select [BEEP]. 7. Select [ON] or [OFF] by pressing the LEFT( )/ RIGHT( ) button. The default is [ON]. 8. Press the Ok button to confirm the setting.
SETTING UP THE CAMERA SYSTEM FORMAT This is used for formatting the internal memory / SD memory card. Formatting the memory Remove the SD memory card to format the internal memory. Insert the SD memory card to format the SD memory card. Steps 1 to 5 are the same as those for selecting the SETUP mode(p.68). 6. Press the UP( ) /DOWN( ) button and select [FORMAT]. 7. Select [YES] or [NO] by pressing the LEFT( )/ RIGHT( ) button and press the OK button.
SETTING UP THE CAMERA SYSTEM POWER OFF This function switches the camera off after a set amount of time in order to prevent unnecessary battery drainage. You can set the power to switch off at any specified time( 3, 5, 10, 30MIN) from the last operation. If you select [CANCEL], the power off function will not operate. Note that the automatic power off does not operate if the camera is in slide show or PC mode. Steps 1 to 5 are the same as those for selecting the SETUP mode(p.68). 6.
SETTING UP THE CAMERA SYSTEM RESET This menu allows you to reset all the camera settings to the default. DATE/TIME, LANGAGE, VIDEO OUT settings will not be changed by doing the [RESET] menu. After resetting the camera system, check the video output signal of the camera is same as that of the country where you are. Refer to following for information on the default. Selecting the default camera setting SETUP 1/3 Steps 1 to 5 are the same as those for selecting the SETUP mode(p.68). 6.
SETTING UP THE CAMERA SYSTEM DATE SETUP Changing the date/time year/month/day, hour/minute by pressing these button. LEFT( ) button : decreases the number of items RIGHT( ) button : increases the number of items 9. Press the Ok button to confirm the setting. SETUP 2/3 DATE SETUP DATE IMPRINT DATE TYPE LANGUAGE ADVANCED Steps 1 to 5 are the same as those for selecting the SETUP mode(p.68). 6. To shift the menu cursor to [SETUP 2/3], press the DOWN( ) button at the [RESET] menu that is in [SETUP 1/3]. 7.
SETTING UP THE CAMERA SYSTEM DATE IMPRINT There is an option to include DATE/TIME on still images. Selecting the date imprint function SETUP 2/3 Steps 1 to 5 are the same as those for selecting the SETUP DATE SETUP mode(p.68). DATE IMPRINT 6. To shift the menu cursor to [SETUP 2/3], press the DATE TYPE DOWN( ) button at the [RESET] menu that is in [SETUP 1/3]. LANGUAGE 7. Press the UP( ) /DOWN( ) button and select [DATE YES NO IMPRINT]. 8.
SETTING UP THE CAMERA SYSTEM DATE TYPE You can select date type that is imprinted on the image. Selecting the date type SETUP 2/3 DATE SETUP DATE IMPRINT DATE TYPE ADVANCED Steps 1 to 5 are the same as those for selecting the SETUP mode(p.68). 6. To shift the menu cursor to [SETUP 2/3], press the DOWN( ) button at the [RESET] menu that is in [SETUP 1/3]. 7. Press the UP( ) /DOWN( ) button and select [DATE TYPE]. 8. Select the desired DATE TYPE by pressing the LEFT( )/ RIGHT( ) button.
SETTING UP THE CAMERA SYSTEM LANGUAGE There is a choice of languages that can be displayed on the LCD monitor. You can select English/ Korean/ German/ French/ Spanish/ Italian/ Taiwanese/ Chinese. Selecting a language SETUP 2/3 Steps 1 to 5 are the same as those for selecting the SETUP mode(p.68). 6. To shift the menu cursor to [SETUP 2/3], press the DOWN( ) button at the [RESET] menu that is in [SETUP 1/3]. 7. Press the UP( ) /DOWN( ) button and select [LANGUAGE]. 8.
SETTING UP THE CAMERA SYSTEM VIDEO OUT The alternating current frequency influences the image quality. In a country that takes NTSC video output type(A.C frequency : 60Hz), select [NTSC/60Hz] sub menu. In a country takes video output type(A.C frequency : 50Hz), select [PAL/50Hz] sub menu. Otherwise, there will be white lines on a stored image. The Movie output signal from the camera can be NTSC or PAL. Your choice of output will be governed by the type of machine (monitor or TV, etc.
SETTING UP THE CAMERA SYSTEM Connecting to an external monitor In STILL IMAGE/ MOVIE CLIP/ PLAY mode, you can view the stored still images or movie clips by connecting the camera to an external monitor via the video cable. When the camera is connected to an external monitor, the LCD monitor will be turned off automatically. When the camera is connected to an external monitor, the menu will be visible on the external monitor and the menu functions are the same as those indicated on the LCD monitor.
PC MODE Starting PC mode If you insert the USB cable to USB connection terminal, the camera working mode will change to the PC mode automatically. In this mode, you can download stored images to your PC through the USB cable. There is no associated menu in PC mode and the LCD monitor is always turned off in PC mode. The camera status LED(red) lamp blinks when the files are transferring via the USB connection. Connecting the camera to PC ADVANCED 1. Turn the camera power on. 2. Turn the PC power on. 3.
PC MODE INFORMATION The camera driver must be installed before using PC mode in Windows 98/98SE. Refer to page 91 regarding installation. To save battery power, it is recommended that you use an AC adaptor(Optional) when connecting the camera to a PC. Downloading stored images Once you have downloaded images to your PC, they can be edited and printed. 1. Connect the camera to your PC with the USB cable. 2.
IMPORTANT NOTES Caution! Your new Samsung camera is a precision instrument. Whilst it is designed to withstand general wear and tear, there are some important points that will help you get maximum service and reliability from your camera. The following should be avoided : Severe changes in temperature and humidity. Dust and dirt. ADVANCED Direct sunlight or the inside of a vehicle in hot weather. Environments where there is high magnetism or excessive vibration.
IMPORTANT NOTES If the digital camera is not used for a long period, an electric discharge can occur. It is a good idea to remove the batteries and the CARD, the camera is not used for some time. If the camera is exposed to electronic interference, it will turn itself off to protect the CARD. Maintenance Use a soft brush (available from photo stores) to GENTLY clean the lens and LCD assemblies. If this does not work, lens-cleaning paper with lens cleaning fluid can be used.
IMPORTANT NOTES Warning indicator There are several warnings that may appear in the LCD display Warning indicator Causes Turn off the camera power and turn it on again Format the memory Card error Turn off the camera power and turn it on again. Remove the card and insert it again Insert the card and format the card There is insufficient memory capacity to take an image. Insert a new CARD Delete unnecessary image files to free up some memory.
BEFORE CONTACTING A SERVICE CENTER Symptom The camera doesn t switch on The camera power is down whilst in use Causes Remedy There is low battery capacity An AC Power Adapter is not connected Insert fresh batteries.
BEFORE CONTACTING A SERVICE CENTER Symptom The camera buttons do not Causes Camera malfunction Incorrect card format Re-format the card (p.70) The card is formatted as FAT 32 Format the card as FAT file file system system(p.66) [VIDEO OUT] type is incorrect Check your video out signal type and stored image. Color of image different to original scene Images are select correct video out type(p.77) WHITE BALANCE setting is Select appropriate WHITE incorrect BALANCE. (p.
BEFORE CONTACTING A SERVICE CENTER Symptom Incorrect date and time is displayed Date is not displayed on the LCD monitor Causes The date and time have been set Reset the date and time correctly. incorrectly. (p.73) Date imprint function is set to OFF Switch the Date imprint function ON. (p.74) in the PLAY mode The external monitor has not been No image on the connected properly with the external monitor camera.
SPECIFICATIONS Image Sensor Type 1/2 CMOS Effective Pixels Approx. 1.3 Mega pixels Total Pixels Approx. 1.4 Mega pixels Focal Length Lens F No. Digital Zoom Focusing Shutter Exposure Flash F 3.0 Still Image mode : 2X Play mode : 2X Optical Viewfinder Optical Viewfinder LCD Monitor 1.6" color TFT LCD Type Fixed focus Range 1.0m ~ infinity Type Electronic shutter Speed 1/15 ~ 1/2,000 sec.. Control Program AE Compensation 2EV (0.
SPECIFICATIONS Image Size Large : 1280x1024 pixels, Small : 640x 512 pixels Capacity Large : Super fine 15, Fine 22, Normal 44 (8MB) Small : Super fine 30, Fine 60, Normal 121 These figures are measured by internal memory based. These figures are measured under Samsung standard conditions and may vary depending on shooting conditions and camera settings.
SOFTWARE MANUAL Software Notes Please ensure that you read the instruction manual carefully before use. The attached software is a camera driver and image editing software tool for Windows. Under no circumstances should all or part of either the software or the user manual be reproduced. Copyright for both software is licensed only for use with a camera. In the unlikely event of a manufacturing fault, we will repair or exchange your camera.
SOFTWARE MANUAL Driver Storage Driver : This enables images to transfer between the camera and PC. This camera uses the USB Storage Driver as the camera driver. You can use the camera as a USB card reader. After installing the driver and connecting this camera to the PC, you can find [Removeable Disk] in [Windows Explorer] or [My computer]. Setting up the camera driver for WINDOWS (p.91) Setting up the camera driver for MAC (p.100) Image Viewer Digimax Viewer 1.
SOFTWARE MANUAL Setting up the USB driver for Windows 98SE To use this camera with a PC, install the Camera Driver first. After this has been done, the stored images in the camera can be moved to the PC and can be edited by an image editing program. Before connecting the camera to the PC, you should first install the camera driver. It is not necessary to install the camera driver if your computer runs on Windows 2000/ ME/ XP. [Click!] 1. Click [ Storage Driver] menu [Click!] 2.
SOFTWARE MANUAL Setting up DirectX 8.1 DirectX is a windows technology that enables higher performance in graphics and sound when you’re playing games or watching video on your PC. 1. After driver installation, [Microsoft DirectX 8.1 Setup] window will open automatically. Click [Yes]. [Click!] 2. The software license agreement window will open. If you agree to it, click [Yes]. This will take you to the next step. If you disagree, click [No] and the installation program will be canceled. 3.
SOFTWARE MANUAL 5. Turn the camera power on. [Found New Hardware Wizard] will open and the computer will recognize the camera. * If you have ever installed an image viewer program, the program will open. If the image viewer program opens, the camera driver was setup successfully. 6. If you can see [Removable Disk] under [My computer], the camera driver installation is successful. Now you can transfer image files from the camera to PC via the USB cable.
SOFTWARE MANUAL INFORMATION Before connecting the camera to the PC, You should first install the camera driver first. After installing the camera driver, you have to restart your PC. If you connect the camera to the PC before installing the camera driver, the [Found New Hardware Wizard] will open. In this case, cancel the [Found New Hardware Wizard] and disconnect the connection. Install the camera driver and connect the camera and PC again.
SOFTWARE MANUAL Removing the USB Driver for Windows 1. Trace [Start Settings] and click [Control Panel] 2. Double-click [Add/Remove programs].
SOFTWARE MANUAL 3. The [Add/Remove Programs Properties] window will open. Click [Digimax 101 Mass Storage Driver] and click [Add/Remove] button. [Click!] 4. A [Select Uninstall Method] window will open. Click the [Next>] button. 5. Uninstall is complete. Click the [Finish] button and the window will disappear.
SOFTWARE MANUAL Removable Disk To use this camera as a Removable Disk, install(p.91) the USB Driver. 1. Before turning the camera power on, connect the camera to the PC with the USB cable. 2. Click [ Removable Disk ] under [My computer] or [ Windows Explorer]. 3. Image files stored in the Removable Disk(Dcim 100sscam) can be transferred to the PC.
SOFTWARE MANUAL Removing the removable disk Windows 98SE 1. Check whether the camera and PC are transferring a file. If the red camera status LED (next to viewfinder) blinks, you have to wait until the LED illuminates. 2. Unplug the USB cable. Windows 2000/ME/XP 1. Check whether the camera and PC are transferring a file.If the red camera status LED (next to viewfinder) blinks, you have to wait until the LED illuminates. 2. Double-click the [Unplug or Eject Hardware] icon on the task bar. [Double-click] 3.
SOFTWARE MANUAL 4. The [Stop a Hardware device] window will open. Select the [USB Mass Storage Device] and click the [OK] button. [Click!] 5. A [Safe to Remove Hardware] window will open. Click the [OK] button. [Click!] 6. A [Unplug or Eject Hardware] window will open. Click the [Close] button and the removable disk will be removed safely. SOFTWARE 7. Unplug the USB cable.
SOFTWARE MANUAL Setting up the USB Driver for MAC Check the MAC OS. You can check the MAC OS version during MAC OS start-up. This camera is compatible with MAC OS 8.6 ~ 10.2. 1. Insert the Application CD-ROM 2. [Digimax 101] icon will display on the desktop. Double-click the [Digimax 101] icon. 3. Double-click the [Digital Camera Driver Installer] icon in the [Digimax 101] folder. 4. A [Digital Camera Driver Installer] window will open. Click the [Install] button.
SOFTWARE MANUAL 5. A information window will open. Click the [Continue] button. 6. Installation is complete. Click the [Restart] button and your PC will restart. 7. Connect the camera to the Macintosh and turn the camera power on. 8. A new icon (Untitled) will be displayed on the desktop after connecting the camera to the MAC. Using the USB Driver for MAC 1. Double click a new icon (Untitled) on the desktop and the folder in the memory will be displayed. 2.
SOFTWARE MANUAL Setting up Digimax Viewer This software is only compatible with Windows. 1. Click [Digimax Viewer 1.0] on the Autorun frame. [Click!] 2. An installation window will be displayed as shown alongside.Click [Next]. [Click!] 3. The Software License Agreement window will display. If you agree to it, click [Yes]. This will take you to the next step. If you disagree, click [No] and the installation program will be canceled.
SOFTWARE MANUAL 4. Select a destination folder and click [Next]. 5. Select the Program folder and click [Next]. [Selecting a destination folder] [Click!] [Click!] 6. Installation is completed. If you wish to open this program automatically whenever the camera is connected to the PC, click the [I would like to launch Digimax Viewer] Checkbox. And click [Finish]. [Check] [Click] SOFTWARE 7. Digimax Viewer will start. Click the Exit button to finish the program.
SOFTWARE MANUAL Digimax Viewer This software is only compatible with Windows. To open Digimax Viewer, click the [ Start Programs Viewer 1.0 ] and Digimax Viewer 1.0 will then open. Samsung Digimax Viewer 1.0 Digimax Select an image and press the right mouse button. A pop-up menu will open. Open : allows you to view a selected sequence of images, one at a time. Copy : copies files. After copying a file, select a folder where you want to paste the copied file.
SOFTWARE MANUAL Setting up MGI PhotoSuite lll SE This software is only compatible with Windows. 1. Click the MGI PhotoSuite lll SE menu on the autorun frame. [Click!] 2. The [Choose Setup Language] window will open. Select language. [Click!] SOFTWARE 3. A [Welcome] window will be displayed. Click [Next>] to move to the next step.
SOFTWARE MANUAL 4. The Software License Agreement window will be displayed. If you agree to this, click [Yes], the window will then move to the next step. If you disagree, click [ No ] and the install program will be canceled. 5. A [Setup Type] window will open. Select setup type and click [Next >] button. Full : the program will be installed with all the options. Custom : you can choose what you would like to install. [Click!] 6.
SOFTWARE MANUAL 7. The MGI Registration window will be displayed. Click the [Continue] button. [Click!] 8. The [Online Registration Utility] window will be displayed. Fill in the blanks and click the [Register] button. 9. Installation is complete. Click the [Finish] button. SOFTWARE A [Read me] file will open. Click [Close button] to close the file.
SOFTWARE MANUAL MGI PhotoSuite III SE This software is only compatible with Windows. To open MGI PhotoSuite lll SE, click the [Start Programs PhotoSuite lll SE] and MGI PhotoSuite lll SE will then open.
SOFTWARE MANUAL An introduction to the Welcome screen Get Get images. Prepare A number of photo editing activities can be performed within this module. Compose Use your photos in a variety of fun, creative and interesting ways. Organize Organize your photos and other media files into albums. SOFTWARE Share Save your results to show to others. Print Print hard copies of photos and projects.
SOFTWARE MANUAL Introduction to navigation bar Back Return to the previous step. Home Return to Welcome screen. Help Display help window. Get Get images. Prepare A number of photo editing activities can be performed within this module. Compose Use your photos in a variety of fun and interesting ways. Organize Organize your photos and other media files into albums. Share Save your results to show to others. Print Print hard copies of photos and projects. Browse Browse the web site.
SOFTWARE MANUAL GET To obtain images from the computer 1. To acquire images, Click the large [Get] button on the Welcome screen, or the [Get] button on the Navigation bar. Click [Computer] from the list of options displayed on the activity panel. 2. The Open file selector is displayed. Now select the image file and click [open]. SOFTWARE 3. The Welcome screen will change to the next work step, with the selected image displayed.
SOFTWARE MANUAL When you obtain images from the digital camera. Before transferring an image file, check the USB connection. 1. To acquire images, click the large [Get] button on the Welcome screen, or the [Get] button on the Navigation bar. Click [Computer] from the list of options displayed on the activity panel. 2. The Open file selector is displayed. Click [Look in :] to choose [Removable Disk( :)] and click [open] for the open file window to be displayed. 3. Select the [ Dcim 100sscam ] folder.
SOFTWARE MANUAL 4. The Welcome screen will change to the next work step, with the selected image displayed. Note When you use the Digimax camera, only [Computer] and [Album] from the list of options displayed are available. [Computer and Album Only] 113 SOFTWARE You will be able to obtain images from the digital camera.
SOFTWARE MANUAL Acquiring images from an Album. 1. To acquire images, click the large [Get] button on the Welcome screen, or the [Get] button on the Navigation bar. Click [Album] from the list of options displayed on the activity panel. 2. After selecting Album on the [ Choose a photo album], click an image in the album and click [Open]. 3. The Welcome screen will change to the next work step, with the selected image displayed. Refer to page 118 for more information about creating an Album.
SOFTWARE MANUAL PREPARE When the image is loaded, the step changes to Prepare automatically. Menu of [PREPARE] steps Rotate & Crop You can rotate, flip or crop images along with a host of others. Touchup Remove Red eye, Remove Scratches etc.. are available in this menu. SOFTWARE Special Effects A number of special effects can be applied. Stitching Join a series of photos together to create a sweeping panoramic effect.
SOFTWARE MANUAL COMPOSE Add text, Compound Images etc. are available in this step. Menu of [COMPOSE] steps Collages : A collage consists of several photos or sections of photos arranged together on a common background. Photo Layouts : The Photo Layouts activity includes many collage and layout options. Cards & tags : Use your photos to create items such as Gift Tags, Greeting Cards, Invitations, Postcards, and Sports Cards.
SOFTWARE MANUAL ORGANIZE Organize your photos and other media files into albums. Menu of [ORGANIZE] steps [ [ [ SOFTWARE Choose a photo album to view or edit] Select Album : To create an Album, click [Organize] in the welcome screen or navigation bar. Album.. : Open Master Album. Select a photo, and choose an action below.] - Open : Open selected image. - Delete : Delete selected image. - Properties... : view image information. Choose an action to manage your album.
SOFTWARE MANUAL Creating an Album 1. To create an Album, click the large Organize button on the Welcome screen, or the Organize button on the Navigation bar. 2. Click [Album..] in [ Choose a photo album to view or edit.] 3. The Master Album window will be displayed, then click [New..]. 4. Put a new Album name in the New Album window and click [OK]. A new album will now be created. 5. [Master Album] window will open. Click [OK] button.
SOFTWARE MANUAL Add images to the album 1. Select [ Choose an action to manage your album. Add..] to add images to the album. [Click!] 2. Click [Computer] in Add Photos menu. [Click!] SOFTWARE NOTICE [Digital Camera(Direct)], [Scanner(TWAIN)], [Digital Camera(TWAIN)] sources can't be used.
SOFTWARE MANUAL 3. [Add photo to Album] window will open. Select images that you want to add. Click [Add] button. [Click!] 4. Adding images is complete.
SOFTWARE MANUAL SHARE Saving or sharing images. Menu of [SHARE] step Save To save the active file according to its current name and path. Save As To assign a new name or path to the file. Send E-mail e-mailing images. Slide Show Viewing images as a slide show.
SOFTWARE MANUAL PRINT You can print images. Menu for the [PRINT] step Print Printing images. Print Multiples Print multiple copies of a photo or project, or one copy of each of the photos included in an album, according to a predefined template. Choose a printer, an orientation, the print size, and the number of copies. You can then print the images. Reference For more information, please refer to the Help file in [Help MGI PhotoSuite lll help].
FAQ About USB Please check the following if the USB connection malfunctions. [Case 1] The camera power is off. Turn the camera power on. We recommend using an AC power adapter in PC mode. If you use batteries, check the battery condition. [Case 2] USB Driver is not installed correctly. Install the USB Driver correctly. Refer to page 91. [Case 3] The USB cable is not connected or you are using a cable with an incorrect specification. Use a USB cable with the correct specification.
FAQ About USB [Case 6] How do I know my computer supports a USB Interface? Check the USB port in your computer or keyboard. Check OS version. USB Interface is available in Windows 98, 98SE, 2000, ME .XP. Check [Universal serial bus controller] in Device Manager. Do the following to check [Universal serial bus controller].
MEMO SOFTWARE 125
MEMO 126
MEMO SOFTWARE 127
SAMSUNG TECHWIN CO., LTD. OPTICS & DIGITAL IMAGING DIVISION 145-3, SANGDAEWON 1-DONG, JUNGWONGU,SUNGNAM-CITY, KYUNGKI-DO, KOREA 462-121 TEL : (82) 31-740-8086,8088, 8090, 8092, 8099 FAX : (82) 31-740-8398, 8111 SAMSUNG OPTO-ELECTRONICS AMERICA, INC. HEADQUARTERS 40 SEAVIEW DRIVE, SECAUCUS, NJ07094, U.S.A. TEL : (1) 201-902-0347 FAX : (1) 201-902-9342 WESTERN REGIONAL OFFICE 18600 BROADWICK ST., RANCHO DOMINGUEZ, CA 90220, U.S.A. TEL : (1) 310-537-7000 FAX : (1) 310-537-1566 SAMSUNG OPTO-ELECTRONICS UK LTD.