SERVICE MANUAL DIGIMAX 101 TECHWIN
CONTENTS Ⅰ. S P E C I F I C A T I O N 1. 2. 3. 4. 5. SPECIFICATION ……………………………………………………………………………………………… 4 SYSTEM REQUIRMENT ……………………………………………………………………………………… 5 TFT LCD PANEL MARK ………………………………………………………………………………………6 CONNECTION DIAGRAM ………………………………………………………………………………………7 PRODUCT EXTERIOR …………………………………………………………………………………………8 Ⅱ . S O F T W A R E I N S T A L L A T I O N ………………………………………………………………………10 Ⅲ. EXPLODED VIEW AND PARTS LIST 1. 2. 3. 4. 5.
Ⅰ. SPECIFICATIONS 1. Specifications Type Image Sensor Lens Viewfinder Focusing Shutter Exposure Flash 1/2 CMOS Effective Pixels Approx. 1.3 Mega pixels Total Pixels Approx. 1.4 Mega pixels Focal Length Samsung Lens f=9.0mm (35mm film equivalent : 46mm) F No. F3.0 Digital Zoom STILL IMAGE : 2X , PLAY mode : 2X Optical Viewfinder Optical viewfinder LCD Monitor 1.6" color TFT LCD Type Fixed focus Range 1.0m ~ infinity Type Electronic shutter Speed 1/15 ~ 1/2,000 sec..
Ⅰ. SPECIFICATION 2 x AA alkaline / 2 x Ni-MH / CR-V3 batteries Power Source AC adapter(Optional) Dimensions (WxHxD) 108x56x37mm / 4.3x2.2x1.5in Weight Approx. 125g / 4.4oz (without batteries and card) Camera Driver Software Application Storage Driver (Windows98/98SE/2000/ME/XP, Mac OS 8.6~10.2) MGI PhotoSuite Digimax Viewer 2.
Ⅰ. SPECIFICATION 4. TFT LCD Panel Mark ■ SHOT mode ⑮ ⑭ ⑬ ① ⑫ ② ⑪ ③ ⑩ ⑨ ④ No. 1 2 3 4 5 6 7 8 9 10 11 12 13 14 15 ⑤ ⑧ ⑥ ⑦ Description Battery Camera shake warning Flash Self-timer White balance Exposure compensation Date Time Card indicator Quality Image size Number of available shots remaining(still image) Recording time(while recording a movie clip) Message for canceling a movie clip recording Digital zoom Recording mode Icons +0.
Batteries Alkarain x2 SD & MMC Card. Digimax 101 camera AC Adaptor USB Cable 7 3.3V/2.0A IBM PC / MACINTOSH Ⅰ. SPECIFICATION 5.
Ⅰ. SPECIFICATION 6.
Ⅰ. SPECIFICATION Viewfinder LCD button Camera status LED (p.15) MODE button MENU button LCD monitor 5-function button Tripod socket THUMBNAIL / UP( ) button FLASH/ LEFT( ) button SELF-TIMER/ RIGHT( ) button OK button (p.
Ⅱ. INSTALLATION All application programs (Digimax Viewer 1.0 for viewing images, MGI PhotoSuite III SE for editing images, and DirectX 8.1 for playing back movie clips) will be installed. If you installed all application programs by clicking the [Driver Storage Driver], you need not install Digimax Viewer 1.0 and MGI PhotoSuite III SE separately. 1. Click [Storage Driver] menu on the Autorun frame. 2. A [Welcome] window will open. Click the [Next>] button.
6. The Software License Agreement window will display. If you agree to it, click [Yes]. 7. Select a destination folder and click [Next]. 8. Select the Program folder and click [Next]. 9. Installation is completed. Click [OK] button and the [MGI PhotoSuite III SE] installation will be started. 10. The [Choose Setup Language] window will open. Select a language and click [OK] button. 11. A [Welcome] window will be displayed. Click [Next>] to move to the next step.
13. A [Setup Type] window will open. Select setup type and click [Next >] button. 12. The Software License Agreement window will be displayed. If you agree to this, click [Yes] button. 14. If the installation is completed correctly, the autoplay is registered automatically into the start menu program as shown below. Click [Next>] button. 15. The MGI Registration window will be displayed. Click the [Continue] button. According to your operating system, the window as shown below may be displayed.
17. Installation is complete. Click the [Finish] button. 18. All application programs are installed correctly. Check [Yes, I want to restart my computer now.] button and click [Finish] button. You must restart your computer after the installation, or your computer can’t recognize the camera as a Removable disk.
Ⅲ. EXPLODED VIEWS AND PARTS LIST 1.
Ⅲ. EXPLODED VIEWS AND PARTS LIST ▶ PARTS LIST Fig.No.
Ⅲ. EXPLODED VIEWS AND PARTS LIST 2.
Ⅲ. EXPLODED VIEWS AND PARTS LIST ▶ PARTS LIST Fig.No. Parts No.
Ⅲ. EXPLODED VIEWS AND PARTS LIST 3.
Ⅲ. EXPLODED VIEWS AND PARTS LIST ▶ PARTS LIST Fig.No. Parts No.
Ⅲ. EXPLODED VIEWS AND PARTS LIST 4.
Ⅲ. EXPLODED VIEWS AND PARTS LIST ▶ PARTS LIST Fig.No. 4-1 4-2 4-3 4-4 4-5 4-6 4-7 4-8 4-9 4-10 4-11 4-12 4-13 4-14 Parts No.
Ⅲ. EXPLODED VIEWS AND PARTS LIST 5. INITIAL PARTS LIST NO PARTS NO.
Ⅳ. ADJUSTMENT 1. Replacement Parts and Adjustment Items Digimax 101 requires electrical adjustments when certain parts are replaced. The table below indicates the adjustments required for the respective part replacements. Main board Strobo board Switch board Lens module TFT LCD Update Firmware ○ AWB adjustment ○ Focus adjustment ○ ○ Bad pixel adjust. ○ Trig adjustment ○ ○ Strobo adjustment ○ ○ LCD adjustment ○ ○ Burnin check ○ ○ ○ ○ ○ 2.
Ⅳ. ADJUSTMENT 3. Firmware Update 1) Firmware version check method a. Turn the power on, at the same time pressing LCD button of camera, MENU button and OK button. b. Firmware version will display on TFT LCD. VE1.14 Version : 1.14 2) Firmware upgrade method a. Download the newest Firmware to SD card.. b. If you insert SD card to camera and turn the power on, red LED will on. c. Firmware will update automatically and after 2∼3 minutes, camera will be OFF automatically with beep sound.
Ⅳ. ADJUSTMENT 2) Bad pixel adjustment and inspection a. Contact to our website (www.ssa.net) and download the each programs. b. Run the adjusting program. ※ How to install the adjusting program 1. Double click thesetup.exe in the SDC1071 folder. 2. A [Welcome] window will open Click the [Next>] button.. 3. Click [Next]. 4. Click [Next].. 5. The warning message will apperr when installing the driver, please click the continue anyway button. 6.
Ⅳ. ADJUSTMENT c. After finishing a setup, run a adjustment program for Bad pixel. (Running program is in SUNAP0916 folder and if you dobule-click SunplusCam_AP.exe, adjustment program will run.) Double click d. After running an adjustment progrm, set a camera to Light source like below picture. When setting, Turn the power on, at the same time pressing LCD button of camera, MENU button and OK button. Light source Camera e.
Ⅳ. ADJUSTMENT f. If a Product information will display, control a camera through MASS in upper menu. g. After checking Snap Rawdata by VC, press a Find Bad Pixel button and test a Bad pixel. h. When finishing a Bad pixel test, the message window about "put a camera to Black image" will appear. i. At this time, after covering a camera with hand or black thing, click "OK(Confirm)" button. j. After finishing a Bad pixel test, "Find 0 Bad pixel!" will appear.
Ⅳ. ADJUSTMENT 3) AWB adjustmen.t a. Turn the power on, at the same time pressing LCD button of camera, MENU button and OK button. (TEST MODE) b. Set up a camera like below picture. Light source Camera c. In TEST mode, change it to Movie mode by pressing Mode button. d. In Movie mode of TEST mode, if you press Right button, AWB adjustment will progress automatically. e. When finishing an adjustment, "OK" will appear on LCD. 4) TRIG adjustment a.
Ⅳ. ADJUSTMENT 5) TFT LCD adjustment a. Disassemble Front cover and Rear cover of camera. b. Turn on the power of camera. (recommended to use Adapter) c. Connect a oscilloscope like below picture. d. Connect a GND to GND of TFT LCD and make Check to be positioned left side of R26. [Fig. no. 1] e. At this time, adjust the output signal by +3.9V, -1.7V.. [Fig. no. 2] f. When finishing an adjustment, assemble a Cover. 29 [Fig. no.
Ⅳ. ADJUSTMENT 6) STROBO adjustment a. Fix a Reflector chart on the wall.. b. Turn the power on, at the same time pressing LCD button of camera, MENU button and OK button. (TEST MODE) c. Set up a camera like below picture. (It is whole dark condition around.) Reflector paper 1.2m Camera Tripod d. In TEST mode, change it to Movie mode by pressing Mode button. e. In Movie mode of TEST mode, if you press Left button, Strobo adjustment will progress automatically. f.
Ⅴ. PRODUCT CONSTRUCTION 1)MAIN PCB Assembly a) Parts Arrangement USB Jack Video Jack 1 .
Ⅴ.
Ⅴ.
Ⅴ.
Ⅴ.
BATTERY CASI 3.3V STROBE CONDENSOR POW BOARD AC JACK 36 TV TV JACK POWER CIRCUIT Main IC AT1382A STROBE CIRCUIT SD CONNECTOR SD CARD BUZZER NAND FLASH K9F6408U0B NOR FLASH SST39VF040 CMOS OV9620 SDRAM K4S641632F SD CONT MCU BOARD DSP SPCA533A LCD CONT USB TO PC POWER SHUTTER SW1 BOARD "1.6"COLOR LCD COM16T1151 Ⅴ. PRODUCT CONSTRUCTION 2.
+3.3v +3.3V +15V +6.8V +5V +3.3V +3.3V +15V +6.8V +5V SM_RDY SM_CE SM_ALE CAS RAS LDQM UDQM SDCLK CKE MWE MD[0..15] MA[0..11] BA0 BA1 STB RIT STH CP STBYB GSRT GPCK GRES DCLK LCD_BL POL DA[0..5] SENSOR +3.3V SENSOR_ON HSYNC VSYNC PCLK EXCLK SIOD SIOC RGB[0..9] CMOS_RST STORAGE SENSOR SD_WPROT SD_CMD SD_CLK SD_DATA[0..3] SD_PROT SD_DET +3.3V TRAP GPIO13 FMGPIO[12..19] STORAGE +3.3V +15V +6.8V +5V LCD +3.3V SENSOR_ON HSYNC VSYNC PCLK EXCLK SIOD SIOC RGB[0..
5 VIDEO +3.3V 5 VIDEO 2 C7 10uF/10V 02237-2GK BUZZER 1 6 IC1 UMC2N UMT5/ROHM 02037-153 2 1 R11 47K,5% 02137-127 1 4 2 2 R5 *220K 02137-1D0 2 R6 *3K 02137-1C7 +5V Q12 DTC114EUA 02037-194 R21 1K 02137-115 Changed R20 390 to 10K 2002/6/6 R20 10K,5% 02137-106 + - 3 2 - 6 1 C9 560pF/50V/5% 02237-634 The through hole for PIEZOCERAMIC BUZZER.
+15V 5 L10 22uH 02337-513 LCD_BL C22 10uF/10V 02237-2GK +5V C19 10uF/25V 02237-2GM L9 22uH 02337-513 C23 10uF/10V 02237-2GK C16 0.1uF/16V 02237-601 D15V C24 0.1uF/16V 02237-601 A5V 5 R204 3.
D3.
ADD GPIO 6 for RESET OV9620 By CMOS_RST 2002/6/14 R41 10K,5% 02137-106 R0402 TP23 T POINT R_0 1 2 1 2 CMOS_RST R42 10K,5% 02137-106 R0402 C39 0.1uZ/16V 02237-601 C0402 1 2 5 1 2 VGA TP9 AD4CH 1 R107 0 R0402 2 1 R105 0 R0402 1 R106 0 R0402 2 2 2 2 2 C35 0.1uZ/16V 02237-601 C0402 SRAMT FREX AVDD_S TP10 TP11 +2.5V_S 1 R103 0 R0402 1 R101 0 R0402 1 R102 0 R0402 ADD PAD R0402 R101,102,103 R105,106,107 NO PART 2002/6/13 ADD PART 0 ohm 2002/8/20 C44 0.
MA[0..11] BA0 BA1 5 5 BA0 BA1 MA10 MA0 MA1 MA2 MA3 LDQM MWE CAS RAS DGND RP3 33 RP4_A_0402 02137-918 2 4 6 8 5 SD_DATA[0..3] 5 5 5 SD_CLK 5 SD_CLK Change the Pin define -Pin 10 SD_DET to SD_ PT R92 47K Pin 11 DGND to SD_D ET 02137-127 Pin 12 SD_PROT to SD_PR OT R0402 2002/6/14 D3.3V SD_DATA0 SD_DATA1 SD_DATA2 SD_PROT SD_DET SD_PROT SD_DET SD_WPROT SD_WPROT SD_CMD 5 D3.3V CASb1 WRITEb CASb0 RASb0 CSb1 ADR14 ADR15 ADR11 ADR1 ADR2 ADR3 ADR4 D7 D5 D6 D3 D4 D1 D2 D0 D3.
5 POWCTRL POWER_OFF 5 POWER_OFF R104 0 R0402 02137-107 R98 10K R0402 02137-106 ADD R104 0 ohm s 2002/6/13 POWCTRL POWER_SW PW+ R100 47K R0402 02137-127 PW+1 TP26 2 1 2 2 3 SPM C119 0.1uF C0402 02237-601 S2 MENU BUTTON 02437-D34 SPM 1 POWER_ON 5 MENU_SW C122 0.1uF C0402 02237-601 100K 02137-128 R96 MODE_SW C121 0.1uF C0402 02237-601 100K 02137-128 R94 1 2 1 D3.
METHOD OF MAIN DISPRODUCT REPAIR IN EACH BOARD MODEL : DIGIMAX 101
1. MAIN BOARD TOP CARD LOCK LIGHT ERROR (BAD SOLDRING) BAD SD CARD RECOGNITION (BAD SOLDRING) C MOS – U2 BAD WORKING – Y2 BAD WORKING – U5 -. HAULT ON SAVING IMAGES -. INTERNAL MEMORY -.
1. MAIN BOARD BOTTOM BATTERY CAPACITY FOR DISPLAY BAD WORKING – Y1 -.ELETRIC CURRENT : UNDER 10uA BAD WORKING – IC4 -. ELECTRIC CURRENT IS 200ma WITH IT’S POWER ON. -. ADJUST F/W UP, AWB, TRIG STROB ,WHEN CHANGING.
2. STROBO DISPRODUCT BAD S/T FLASH–XE TUBE BAD S/T CHARGE – T1 BAD S/T FLASH–T2 BAD WORKING –F1 (3A) BAD WORKING – U2 (SWITCH POWER IC) -. TEMPORAL ELECTRIC CURRENT GENERATES UNDER 100MA WITH POWER ON., BAD WORKING – J1 (DC JACK) -. ONE IS WORKING, ANOTHER ONE IS NOT BETWEEN BATTERY AND ADAPTER.
3.
REDKLAS DG-101 DOMESTIC DISPRODUCT RECEPTION ANALYSIS ORDER BODY NO 1 PRODUCE DATE ALL DISPRODUCT NAME(EFFECT) CAUSE -. STRIP NOISE WHEN TAKING A -. WORKING ON FIRM WARE IMPROVEMENT PICTURE IN WHITE BACKGROUND,AND IN FLUORESCENT LAMP. 2 83108698 82602766 82603158 '03.01 -. DOESN'T WORK WITH "MEMORY FULL" LETTER.(MEMORY LETTER DOESN'T COME UP) -.THERE IS AN ERROR WHEN SAVING IMAGES IN FLASH MEMORY. -. POWER ON NG -.
DISPRODUCT #1 DISPRODUCT #8 DISPRODUCT #9 비고 DISPRODUCT #19~ #25 DISPRODUCT # 26 DISPRODUCT #29 비고 -2-
