DMR78 Series DMR77 Series DMR57 Series Dishwasher installation guide These installation instructions are intended for use by qualified installers. STOP If you are having problems installing this dishwasher Please call : 1-800-SAMSUNG (726-7864) for assistance : www.samsung.com imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.
safety instructions Throughout this manual, you’ll see Warning and Caution notes. These warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It’s your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.
GROUNDING INSTRUCTIONS For a permanently connected appliance: This appliance must be connected to grounded metal, a permanent wiring system, or an equipment-grounding conductor must be run with the circuit conductors and connected to the equipment-grounding terminal or lead on the appliance. The dishwasher is very heavy. Do not attempt to move or carry a dishwasher alone. Two or more people are needed to move a dishwasher and avoid potential injuries.
contents preparing the dishwasher enclosure 5 Product dimensions 5 Cutout dimensions installing the dishwasher 6 STEP 1 8 STEP 2 5 6 specifications 19 _ contents Checking the parts and tools electing the best location for the S dishwasher 9 STEP 3 Water supply requirements 10 STEP 4 Electrical requirements 11 STEP 5 Preparing the dishwasher 12 STEP 6 Placing the dishwasher and connecting water supply line 13 STEP 7 Leveling the dishwasher 14 STEP 8 Securing the dishwasher 15 STEP 9 Co
preparing the dishwasher enclosure Product dimensions 27” (686 mm) Rear view (DMR78 series DMR77 Series/ DMR57 Series) 33 3/4” (857 mm) 23 7/8” (606 mm) 20 1/2” (520 mm) 24 1/2” (622 mm) Side view (DMR57 series) 24 3/4” (629 mm) 2 1/2” (64 mm) 1 3/4” (44 mm) The water supply line, power cable and drain hose should go through this part.
installing the dishwasher Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you’re not at risk of injury when washing dishes. STEP 1 Checking the parts and tools Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process.
Tools required Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole cutter Level installing the dishwasher _ 02 Installing the dishwasher Electric drill
installing the dishwasher New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, the connections for the dishwasher being replaced must be checked for compatibility with the new dishwasher and replaced as necessary. STEP 2 Selecting the best location for the dishwasher The following criteria are important to ensure the best location for the dishwasher. 1.
STEP 3 Water supply requirements
installing the dishwasher STEP 4 Electrical requirements The electrical requirements for the dishwasher are as follows: • In the United States, in accordance with the National Electric Code/State and Municipal codes and/or local codes. • In Canada, in accordance with the Canadian Electric Code C22.1-latest edition/Provincial and Municipal codes and/or local codes. 1. The dishwasher must be connected with the correct rated voltage supply marked on the rating plate of the unit. 2.
STEP 5 Preparing the dishwasher
installing the dishwasher STEP 6 Placing the dishwasher and connecting water supply line 1. Adjust the four leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (Refer to the figures in STEP 7.) 2. Locate the water supply line for connecting the inlet valve on the left and the power cable for connecting the junction box on the right. 3.
STEP 7 Leveling the dishwasher 1. Open the door and place the level against the top of the tub from inside and check whether the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. 02 Installing the dishwasher 2. Check whether the dishwasher is upright (perpendicular), as shown in the figure to the right. 3. Open the door of the dishwasher and check whether both the tub and door clearances are correct.
installing the dishwasher STEP 8 Securing the dishwasher The dishwasher should be fixed to the countertop or side walls for additional stability and safety. 1. When the countertop is made of wood or the material will not be damaged by drilling, follow the instructions in 2-1 below. When the countertop is made of granite, marble or any other kind of material that can be damaged by drilling, follow the instructions in 2-2 below. 2-1.
STEP 9 Connecting the drain hose 1. Check the parts on the sink to which the drain hose is connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. Connecting the drain outlet must be done in accordance with the water pipe installation regulations in your region. Garbage disposal With an air gap Without an air gap Air gap Drain hose Hose clamp Hose clamp Case 2.
installing the dishwasher 3. Check the size of the sink’s drain hose connector. If needed, cut the drain hose so its end fits into the sink connector (1/2 in., 3/4 in. or 1 in. - as shown in the Figure below). If the end of the drain hose does not fit into the drain hose connector of the sink, use an adaptor purchasable at a plumbing/hardware supply store. 4. When connecting the drain hose, make sure to fasten it using a hose clamp. Failing to do so may cause water leakage. 5.
STEP 10 Wiring connections Black to black Power cable Junction box White to white Green to green (Ground to ground) Strain relief installing the dishwasher _17 02 Installing the dishwasher 1. Before connecting the power cable to the dishwasher, make sure to turn off the circuit breaker. 2. Check to remove the junction box cover located at the bottom right at the front of the dishwasher. You will find three power wires from the dishwasher including the grounding line. 3.
installing the dishwasher STEP 11 Completing the installation 1. 2. 3. 4. Open the door and remove all foam, paper packaging and unnecessary parts. Turn on the circuit breaker turned off before beginning the installation. Open the water supply valve to supply water to the dishwasher. Turn on the dishwasher, and select and run a cycle. Check whether the power turns on correctly or whether there is any water leakage while the dishwasher is operating.
specifications 120 V, 60 Hz AC only Water pressure 20 ~ 120 psi (140 ~ 830 kPa) Dimensions (Width×Depth×Height) 237/8 x 243/4 x 337/8 in. (605 x 627 x 860 mm) Nominal inlet water temperature 120 ˚F (49 ˚C) Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual.
QUESTIONS OR COMMENTS? COUNTRY CALL OR VISIT US ONLINE AT USA 1-800-SAMSUNG (726-7864) www.samsung.com CANADA 1-800-SAMSUNG (726-7864) www.samsung.com/ca/ Code No.