FlexDry™ User manual DVE(G)60A9900* Untitled-5 1 2021-05-25 5:20:35
Contents English Safety information 4 What you need to know about the safety instructions Important safety symbols CALIFORNIA PROPOSITION 65 WARNING Important safety precautions Warnings Cautions 4 4 5 6 8 8 Regulatory notice 10 FCC Notice IC Notice Open Source Announcement 10 11 12 Installation requirements 13 Key installation requirements Location considerations Ducting requirements Exhausting requirements Gas requirements Electrical requirements 13 13 16 17 18 19 Installation 21 What’s inc
40 Control panel Operating a cycle Cycle overview Options System functions Special features Cycle chart Drying guide 40 42 43 45 49 51 53 58 Maintenance 59 General cleaning and maintenance instructions Upper dryer Lower dryer 59 60 61 Troubleshooting 62 Checkpoints Information codes 62 64 Specifications 65 Fabric care chart Protecting the environment Specification sheet 65 66 66 English Untitled-5 3 2021-05-25 English Operations 3 5:20:35
Safety information English Congratulations on your new Samsung dryer. This manual contains important information on the installation, use and care of your appliance. Please take some time to read this manual to take full advantage of your dryer’s many benefits and features. What you need to know about the safety instructions Please read this manual thoroughly to ensure that you know how to safely and efficiently operate the extensive features and functions of your new appliance.
English WARNING - Risk of Fire • Clothes dryer installation must be performed by a qualified installer. • Install the clothes dryer according to the manufacturer’s instructions and local codes. • Do not install a clothes dryer with flexible plastic venting materials. If flexible metal (foil type) duct is installed, it must be of a specific type identified by the appliance manufacturer as suitable for use with clothes dryers.
Safety information Important safety precautions English WARNING To reduce the risk of fire, electric shock, or injury to persons when using your appliance, follow basic precautions, including the following: 1. Read all instructions before using this appliance. 2. Do not dry articles that have been previously cleaned in, washed in, soaked in, or spotted with gasoline, dry-cleaning solvents, or other flammable or explosive substances, as they give off vapors that could ignite or explode. 3.
English 18. Do not allow children to play on or in the appliance. Close supervision of children is necessary when the appliance is used near children. 19. Do not insert your hand under the dryer. -- This may result in injury. 20. Take care that children’s fingers are not caught in the door when closing it. -- This may result in injury. 21. The control board and inlet valve are intentionally not grounded and may present a risk of electric shock only during servicing.
Safety information English WARNING - What to do if you smell gas: • • • • • • Do not try to light any appliance. Do not turn on the appliance. Do not touch any electrical switch. Do not use any phone in your building. Clear the room, building or area of all occupants. Immediately call your gas supplier from a neighbor’s phone. Follow the gas supplier’s instructions. • If you cannot reach your gas supplier, call the fire department.
English • Do not use fabric softeners or products to eliminate static unless the softener or product is recommended for dryer use by the manufacturer of the fabric softener or product. • Clean the lint screen before or after each load. • Keep the area around the exhaust opening and surrounding areas free from lint, dust, and dirt. • The interior of the dryer and exhaust duct should be cleaned periodically by qualified service personnel. • This appliance must be properly grounded.
Regulatory notice FCC Notice English CAUTION Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This device complies with Part 15 of FCC Rules. Operation is Subject to following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received including interference that cause undesired operation.
Unintentional emitter per FCC Part 15 English Product type : Clothes Dryers Model : DVE(G)60A9900* Responsible Party – U.S. Contact Information Samsung Electronics America, Inc. QA Lab America 19 Chapin Rd. Building D Pine Brook NJ 07058 Tel: 1-973-808-6375 Fax: 1-973-808-63 IC Notice The term “IC” before the radio certification number only signifies that Industry Canada technical specifications were met. Operation is subject to the following two conditions: 1.
Regulatory notice Open Source Announcement English The software included in this product contains open source software. The following URL http://opensource.samsung.com/opensource/SMART_TP2_0/seq/0 leads to open source license information as related to this product. NOTE Hereby, Samsung Electronics, declares that the radio equipment type appliance is in compliance with Directive 2014/53/EU.
Installation requirements Read through the following instructions before installing the dryer and keep this manual for future reference. English WARNING Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. Key installation requirements • • • • A grounded electrical outlet.
Installation requirements Alcove or closet installations English WARNING • The dryer must be exhausted to the outside to reduce the risk of fire when installed in an alcove or closet. • No other fuel-burning appliance should be installed in the same closet as the dryer. • Place the dryer at least 18 inches (460 mm) above the floor for garage installation. Minimum clearances between the dryer and adjacent walls or other surfaces: Sides 1 in. (25 mm) Rear 5.9 in. (150 mm) Top 21 in.
Side by side installation English C A A B D B A E F A 1 in. (25 mm) D 32.5 in. (825 mm) B 27 in. (686 mm) E 2 in. (50 mm) C 21 in. (533 mm) F 5.9 in. (150 mm) A A 61 in.
Installation requirements Ducting requirements English Recommended Use only for short-run installation 4” (10.2 cm) 2.5” (6.4 cm) Weather hood type No. of 90° elbows Rigid Rigid 0 80 ft. (24.4 m) 74 ft. (22.6 m) 1 68 ft. (20.7 m) 62 ft. (18.9 m) 2 57 ft. (17.4 m) 51 ft. (15.5 m) 3 47 ft. (14.3 m) 41 ft. (12.5 m) NOTE * Use a 4-inch (10.2 cm) diameter rigid aluminum or galvanized steel duct.
Exhausting requirements English The dryer must not be exhausted into a chimney, a wall, a ceiling, an attic, a crawl space, or a concealed space of a building. Exhausting the dryer to the outside will prevent large amounts of lint and moisture from being blown into the room. In the United States and Canada • All dryers must be exhausted to the outside. • The required exhaust duct is 4 inches (10.2 cm) in diameter.
Installation requirements Gas requirements English WARNING • Use only natural or LP (liquid propane) gases. • The installation must be conformed with local codes, or in the absence of local codes, with the national fuel gas code, ANSI Z223.1/NFPA 54, latest revision (for the UNITED STATES), or with the natural gas and propane installation code, CSA B149.1 (for Canada). • Gas dryers are equipped with a burner vent for use with natural gas.
Electrical requirements English The wiring diagram is located on the plate under the control panel or rear frame. WARNING • Improperly connecting the equipment grounding conductor can result in a risk of electric shock. Check with a qualified electrician or serviceman if you are in doubt as to whether your dryer is properly grounded. Do not modify the plug provided with your dryer – if it doesn’t fit the outlet, have a proper outlet installed by a qualified electrician.
Installation requirements Electrical connections English Before operating or testing, follow all grounding instructions in the “Grounding” section. An individual branch (or separate) circuit serving only your dryer is recommended. Do not use an extension cord. Gas models – U.S. and Canada A 120 volt, 60 Hz AC approved electrical service with a 15-ampere fuse or circuit breaker is required. Electric models – U.S. only Most U.S. dryers require a 120 / 240 volt, 60 Hz AC approved electrical service.
Installation This dryer must be installed by a qualified technician. The installer is responsible for connecting the dryer to the main power while observing the relevant safety regulations of your area. English What’s included Make sure all the parts are included in the product package. If you have a problem with the dryer or the parts, contact a local Samsung customer center or the retailer.
Installation Accessories (supplied) English Y-connector Water hose (Canadian elec. models only) Flexible rack Dryer-sheet case Short water hose Accessories (not supplied) You must purchase these items at a local service center.
Tools needed for installation English Pliers Cutting knife Pipe wrench (gas models only) Nut screwdriver Phillips screwdriver Duct tape Wrench LPG-safe compound or Teflon Tape (for gas installation) Level WARNING Packing materials can be dangerous to children. Keep all packing materials (plastic bags, polystyrene, etc.) out of children’s reach.
Installation Step-by-step installation English Make sure you have a qualified technician install the dryer. Step by step installation instructions start below. • Do not remove the protective film on the doors before completing the product installation. If you remove the protective film before the installation is complete, the doors may get scratched or damaged during installation. • Make sure the installation location allows enough space for the dryer doors to be fully open.
STEP 3 Connect the electrical wiring (for electric models) English Before connecting the electrical wiring, make sure you have read the “Electrical requirements” section on page 19. 3-wire system 1. Loosen or remove the screws from the center terminal block. 2. Connect the neutral wire (white or center wire) of the power cable to the center, silver-colored terminal screw of the terminal block. Tighten the screws. 3. Connect the other wires to outer terminal block screws. Tighten the screws.
Installation 4-wire system English 1. Remove the external ground connector’s screw and connect the ground wire (green or unwrapped) of the power cable to the screw. CAUTION F D A B C L2 L1 E A. External ground connector B. Neutral grounding wire (white) C. Center silver-colored terminal block screw D. Neutral wire (white or center wire) E. 3/4” (1.9 cm) UL-listed strain relief -- To connect the ground wire to the neutral position without through contact A (cabinet ground), contact a technician.
STEP 4 Connect the water hose (applicable models only) English The dryer must be connected to a cold water tap using the provided water hoses. 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the female end of the Y-connector to the cold water tap. 2. Connect the straight end of the water hose to the Y-connector. Tighten the hose coupling by hand. 3. Using pliers, tighten the coupling an additional twothirds turn.
Installation Using the short hose as an extension English 1. Close the cold water tap. If you have a washer’s cold water hose attached to the cold water tap, unscrew and remove the hose. Then, connect the short hose (B) to the cold water tap. Turn the coupling by hand until it is tight. 2. Using pliers, tighten the coupling an additional twothirds turn. Do not overtighten. You can damage the coupling. B 3. Connect the Y-connector (A) to the brass male end of the short hose.
STEP 5 Level the dryer English To ensure optimal performance, the dryer must be level. Using a level (A), check if the dryer is level side to side and then front to back. If the dryer is not level, turn the leveling legs (B) clockwise to lower the dryer or counterclockwise to raise the dryer. A B NOTE A B • To set the dryer to the same height as your washer, fully retract (A) the leveling legs by turning them counterclockwise, then loosen (B) the feet by turning them clockwise.
Installation STEP 6 Power on (for gas models) English Make sure all gas connections, the exhaust line, and all wiring is connected correctly. Then, plug the power cord into a power source and check the dryer’s installation and operation using the final checklist in Step 7. STEP 7 Final Check When installation is complete, confirm that: • • • • • • The dryer is plugged into an electrical outlet and grounded properly. The exhaust ductwork is connected, and the joints are taped.
Vent blockage test English After the dryer is installed, run the Vent Blockage Test function to check if the duct system is properly installed. Vent Blockage Test automatically detects the status of the ducts and reports any blockage or problems. Proper ducting can reduce drying time and save energy. NOTE The Vent Blockage Test function must run when the dryer is cool. If the dryer warms up after the installation check, run the Air Fluff cycle for several minutes to reduce its internal temperature.
Installation Installation check codes English Check code No problems detected Meaning Solution Vent condition is good. 1. Clean the lint filter. Vent is nearly clogged Over 80 % of the vent is clogged. (This may lead to poor drying performance or cause malfunction) Leave the dryer at room temperature The internal temperature of the dryer is too low (below 32 °F (0 °C)) or too high (over 104 °F (40 °C)) and therefore vent blockage cannot be detected.
Exhaust ducting guide English Ducting 1. Make sure the dryer is installed properly so the air exhausts freely. 2. Use 4-inch rigid metal ducts. Tape all joints including the dryer connection. Never use lint-trapping screws. 3. To facilitate the exhaust, keep the ducts as straight as possible. Cleaning Clean all old ducts before installing the dryer, and make sure the vent flap opens and closes freely. We recommend that you clean the exhaust system annually or on a regular basis.
Installation English 6. Remove the two screws above and below the lever holder on the opposite side of the door opening. 7. Remove the two screws that hold the lever holder in place, and then remove the lever holder. 8. Re-insert the two screws that held the lever holder into the same screw holes, and then tighten. 9. Remove the single screw from the back of the door hinge.
English 10. Insert the screw you just removed into the other screw hole on the back of the door hinge, and then tighten. 11. Place the door on the other side, and then reattach it to the dryer. NOTE Insert the head of the screw on the back of the hinge into the hole above the cut out in the frame, and then slide the door hinge down until it stops. Make sure the protrusion on the back of the hinge is pressed into the cut out before you tighten the hinge screws. 12.
Before you start Here are a few things you should know before starting your dryer. English Initial setup • When you turn on your dryer for the first time, the screen shows the initial setup process. Follow the on-screen instructions to complete it. • If you complete the initial setup and operate a cycle for more than a minute, the initial setup will not appear again. • The initial setup includes language selection and a brief tutorial. • When tapping a button, tap exactly over the text.
Sort and load • • • • English • • • • Put one wash load in the dryer at a time. Do not mix heavy and lightweight items together. To improve drying efficiency for one or two items, add a dry towel to the load. For best results, untangle items before inserting them into the dryer. Tangled items may degrade the drying efficiency or cause the door to open. Overloading reduces the tumbling action, resulting in uneven drying and wrinkling.
Before you start Rack guidelines English Flexible rack The flexible rack is designed to dry delicate items that are not suitable for or cannot be dried in the lower dryer. To use the flexible rack A 1. Locate the rack supports (x4) in each corner of the upper dryer. Push down the lower area of the front 2 supports to unfold. The rear 2 supports are fixed. 2. Insert the flexible rack (A) inside the upper dryer. Make sure all 4 corners of the rack sit on the rack supports properly.
Rack Dry (applicable models only) If a drying rack is not provided, you can purchase it at a local Samsung service center. (Part Code : DC9300374G) To use the drying rack, follow these steps: 1. Insert the drying rack (A) inside the tumbler with the filter handle to the front. 2. Insert the rear legs of the drying rack into the recessed areas of the rear wall, and then press down the middle of the drying rack to secure it in place. A 3. Put items to dry on the rack.
Operations English This FlexDry™ dryer features the upper dryer and the lower dryer for your convenience. The upper dryer is a top load dryer that is designed to dry relatively small loads while the lower dryer is a drum loader you can use to dry normal or relatively heavy loads. WARNING To reduce the risk of fire, electric shock, or injury, read the “Safety information” before operating this appliance. CAUTION Do not spray water onto the control panel. This may cause a system failure.
You can start or pause the operation. English 04 Start/Pause • The upper button controls the upper dryer, and the lower button controls the lower dryer. • Tap and hold the button to start the operation. • During the operation, tap the button to pause. 05 Display The display shows the current cycle, estimated time remaining, cycle options, and other useful or alert messages. 06 OK Tap to confirm your selection of function or setting. Tap to change the dry level for the selected cycle.
Operations Icon description English Wi-Fi This icon indicates that the dryer is connected to Wi-Fi. Smart Control This icon indicates that Smart Control is on. For more information on “Smart Control”, see page 51. This icon indicates that Child Lock is on. Child Lock For more information on “Child Lock”, see page 48. Operating a cycle 03 05 01 02 07 06 1. Tap 04 05 to turn on the dryer. 2. Tap UPPER or LOWER. -- Tap UPPER to select the upper dryer and use its features.
Cycle overview English NOTE Other cycles can be used after adding them to your cycle list using the My Cycles function. For more information, see the “My Cycles” section on page 47.
Operations Cycle Description English Bedding For bulky items such as blankets, sheets, comforters, and light duvets. Activewear For exercise wear and outdoor wear such as sports jerseys, training pants, water-repellent jackets, and other performance clothing. Thick fabrics like a zipper or velcro closure of a jacket, or training socks may not be completely dried. Denim Use a stepped drying temperature for removing moisture of Jeans and denims. Shirts Use to quickly dry a few items such as a shirt.
Options English Using Options 02 03 01 1. Tap UPPER or LOWER to select the upper or lower dryer. 2. Tap Options. 3. Turn the Navigation dial to select the desired additional function. 4. Tap OK to change the selected function’s settings or start the function. NOTE • To return to the main screen, tap Options again or turn the Navigation dial to select Back, and then tap OK. • If the selected function is not supported, the "Currently not supported" message is displayed, and the OK button is not activated.
Operations Super Speed English Super Speed increases the fan speed to shorten the drying time. This option is available for the Blouses, Undergarments and Accessories cycles. 1. Tap UPPER. -- This function is not available for the lower dryer. 2. Tap Options. 3. Turn the Navigation dial to select Super Speed, and then tap OK. 4. Tap OK to select On or Off. Wrinkle Prevent Reduces wrinkles by rotating the drum intermittently after completing the dry cycle.
AntiStatic English Reduces static electricity that occurs from clothing friction. This is done by spraying steam in a later stage of the drying cycle. The AntiStatic function is only available with Normal, Heavy Duty, Perm Press, Delicates, and Time Dry. In the Normal, Heavy Duty, Delicates, and Perm Press cycles, you can use this function if the dryness setting is 3 or higher. 1. Tap LOWER. -- This function is not available for the upper dryer. 2. Tap Options. 3.
Operations Drum Light English You can turn the drum light on or off. 1. Tap LOWER. -- This function is not available for the upper dryer. 2. Tap Options. 3. Turn the Navigation dial to select Drum Light, and then tap OK. 4. Tap OK to select On or Off. -- The drum light turns on even when the dryer is off. (If the dryer is plugged into a power outlet.) -- When the dryer door opens, the drum light automatically turns on and automatically turns off after 2 minutes.
System functions English Using System Functions 02 01 * 03 * Tap and hold 3 seconds. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial and select the desired system function, and then tap OK. 3. Tap OK to change the selected function’s settings or start the function. NOTE • To return to the main screen, tap Options again or turn the Navigation dial to select Back, and then tap OK.
Operations Alarm English You can enable/disable alarm sounds. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial to select Alarm, and then tap OK. 3. Tap OK to select On or Off. -- The default setting is On. NOTE The setting remains unchanged even if you restart the dryer. Wi-Fi You can turn the dryer's Wi-Fi on or off. 1. Tap and hold Options for 3 seconds. 2. Turn the Navigation dial to select Wi-Fi, and then tap OK. 3. Tap OK to select On or Off.
Special features English Smart Control You can connect to the SmartThings app and control your dryer remotely. (Smart Control for electric model, Smart Monitor for gas model) Connecting your dryer • Download and open the SmartThings app on your mobile device • Tap to turn on the dryer. • Tap and hold Smart Control / Smart Monitor on the dryer. a. The dryer enters AP mode and connects to your mobile device. b. Tap Smart Control / Smart Monitor to authenticate your dryer on your mobile device. c.
Operations SmartThings English Wi-Fi connection On your smartphone, go to Settings and turn on the wireless connection and select an AP (Access Point). • This appliance supports the Wi-Fi 2.4 GHz protocols. Download On an app market (Google Play Store, Apple App Store, Samsung Galaxy Apps), find the SmartThings app with a search term of “SmartThings”. Download and install the app on your device. NOTE The app is subject to change without notice for improved performance.
Cycle chart English Upper dryer • The drying time depends on the load and the item type. To shorten the drying time, use Super Speed. • For manual-wash items, use a towel to remove moisture from the items before drying. • To reduce the drying time of the items that are machine-washable, set the spinning option on your washer to high to remove as much moisture as possible. • Arrange items as even and straight as possible. Overlapped items may not be dried well.
Operations NOTE English : factory setting, : can be selected Cycle Time Blouses Sweaters Undergarments Accessories Options Air Fluff Super Speed CAUTION Clothing with accessories or hooks may get stuck in the mesh of the rack. • Clothing with accessories must face upwards. • Clothing with hooks must be hooked up before being placed.
Not Recommended for the upper dryer English Do not dry shoes, bags, down/fur products, rugs, carpets, or bulky items in the upper dryer. Do not dry shoes, bags, down/fur products, rugs, carpets, or bulky items in the upper dryer.
Operations Lower dryer English NOTE For best results, follow the load size recommendations for each dry cycle. • Large load: Fill the drum to about 3/4 full. Do not add items over this level as they need to tumble freely. • Medium load : Fill the drum to about 1/2 full. • Small load : Fill the drum with 3-5 items, not more than 1/4 full.
NOTE Cycle Functions (Temp.
Operations Drying guide English The best way to dry items is to follow the instructions on the care label. If no drying instructions are provided, see the following table for reference. Lower dryer Items Description Follow the care label instructions or dry using Bedding. Bedspreads & Comforters Blankets Curtains & Draperies • Make sure the item is thoroughly dry before using or storing. • May require repositioning in the drum to ensure even drying.
Maintenance Keep your FlexDry™ dryer clean to prevent decreased performance and to lengthen its life. WARNING English Certain internal parts are intentionally not grounded and may present a risk of electric shock only during servicing. Service Personnel - Do not contact the following parts while the appliance is energized: Control board and inlet valve. General cleaning and maintenance instructions Control panel • • • • Clean with a soft, damp cloth. Do not use abrasive substances.
Maintenance Upper dryer English Flexible rack • If you use the flexible rack, make sure to clean the rack after every use so that it is readily available for future use. • Clean the rack with neutral cleaning agents and running water. Upper recesses • Clean the left and right rear recesses of the upper dryer after every use. • Locate the recesses in the rear corners of the upper dryer, and then remove the recess covers on both sides. • The upper dryer may have collected water while it is operating.
Lower dryer English Stainless steel drum • Clean the drum after every use. • To clean the stainless steel drum, use a damp cloth with a mild, non-abrasive cleaner suitable for easily marred surfaces. Remove cleaner residue and dry with a clean cloth. Drying rack • If you used the lower drying rack, make sure to clean the rack after every use so that it is readily available for future use. • Clean the drying rack with neutral cleaning agents and running water.
Troubleshooting Checkpoints English If you encounter a problem with the dryer, first check the table below and try the suggestions. Problem Dryer does not start. The dryer does not warm up. Action • • • • • • • Make sure the dryer is plugged in. Make sure the door is properly closed. Check the fuse or reset the circuit breaker. If you opened the door during a cycle, tap and hold again. Clean the filter. Make sure Child Lock is not activated.
Problem Action Items are not dried evenly. • Seams, pockets, and other parts of clothing are harder to dry than others. This is normal. • Sort heavy and light items separately. There is a smell coming from the dryer. • The smell of paint, varnish, cleaning agents, and other household items could have circulated in the air and entered the dryer. If you notice such a smell, ventilate completely before using the dryer. • If drying in an enclosed area, the dryer could cause the ambient temperature to rise.
Troubleshooting Problem Action English • Some cycles automatically sense the moisture in the load and shut the dryer off when the selected dryness level is reached. The drying time can change according to the type and amount of laundry. See the cycle chart for reference. Extended time. If a problem persists, contact a local Samsung service center. Information codes If the dryer fails to operate, you may see an information code on the display panel.
Specifications Fabric care chart Wash cycle Normal Permanent press/Wrinkle resistant/ Wrinkle control English The following symbols provide garment care direction. The clothing care labels include symbols for drying, bleaching, ironing, and dry cleaning. The use of symbols ensures consistency among garment manufacturers of domestic and imported items. Follow care label directions to optimize garment life and reduce laundering problems.
Specifications Warning symbols for laundering Dry-clean English Do not wash Dry-clean Do not wring Do not dry-clean Do not bleach Line dry / Hang to dry Do not tumble dry Drip dry No steam (added to iron) Dry flat Do not iron Protecting the environment This appliance is manufactured from recyclable materials. If you decide to dispose of this appliance, please observe local waste disposal regulations. Cut off the power cord so that the appliance cannot be connected to a power source.
LIMITED WARRANTY (U.S.A.) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL CONSUMER PURCHASER WITH PROOF OF PURCHASE This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS AMERICA, INC.
LIMITED WARRANTY (U.S.A.) Visits by an authorized servicer to explain product functions, maintenance or installation are not covered by this limited warranty. Please contact SAMSUNG at the number below for assistance with any of these issues. EXCLUSION OF IMPLIED WARRANTIES IMPLIED WARRANTIES, INCLUDING THE IMPLIED WARRANTIES OF MERCHANTABILITY OR FITNESS FOR A PARTICULAR PURPOSE, ARE LIMITED TO ONE YEAR OR THE SHORTEST PERIOD ALLOWED BY LAW.
Warranty (CANADA) SAMSUNG DRYER LIMITED WARRANTY TO ORIGINAL PURCHASER This SAMSUNG brand product, as supplied and distributed by SAMSUNG ELECTRONICS CANADA, INC.
Warranty (CANADA) EXCEPT AS SET FORTH HEREIN, THERE ARE NO WARRANTIES ON THIS PRODUCT EITHER EXPRESS OR IMPLIED, AND SAMSUNG DISCLAIMS ALL WARRANTIES INCLUDING, BUT NOT LIMITED TO, ANY IMPLIED WARRANTIES OF MERCHANTABILITY, INFRINGEMENT OR FITNESS FOR A PARTICULAR PURPOSE. NO WARRANTY OR GUARANTEE GIVEN BY ANY PERSON, FIRM, OR CORPORATION WITH RESPECT TO THIS PRODUCT SHALL BE BINDING ON SAMSUNG.
Memo Untitled-5 71 2021-05-25 5:20:46
Scan this with your smartphone This product qualifies for ENERGY STAR in the factory default "Normal + Eco dry" setting. If you change the factory default setting or enable other features, power consumption could increase and exceed the limits qualified for ENERGY STAR. QUESTIONS OR COMMENTS? COUNTRY CALL U.S.A 1-800-SAMSUNG (726-7864) CANADA 1-800-SAMSUNG(726-7864) OR VISIT US ONLINE AT www.samsung.com/us/support www.samsung.com/ca/support (English) www.samsung.
