......... _Own I structi Register your product at www.samsung.com/global/register Record your Model and Serial number here for future reference. - Model - Serial No.
I Important Warrantyinformation RegardingTelevisionFormatViewing Wide screen format PDP Displays (18:9, the aspect ratio of the screen width to height) are primarily designed to view wide screen format full-motion video. The images displayed on them should primarily be in the wide screen 16:9 ratio format, or expanded to fill the screen if your model offers this feature and the images are constantly moving.
User instructions O Screen image retention Do not display a still image (such as on a video game) on the plasma display panel for more than several minutes as it can cause screen image retention. This image retention is also known as "screen burn". To avoid such image retention, refer to page 26 of this manual to reduce the degree of brightness and contrast of the screen when displaying a still image. Altitude The PDP can only operate normally at heights under 6500ft.
i Contents ] R List of Features .............................................................. m Accessories .................................................................... 5 5 m Viewing the Controt Panel ............................................. m Viewing the Connection Panel ....................................... m Remote Control .............................................................. 6 7 8 R Installing Batteries in the Remote Control .....................
General information List of Features • Adjustable picture settings that can be stored in the TV's memory. • Automatic timer to turn the TV on and off. • A speciaI sleep timer. • V-Chip function. • Excellent Digital Interface & Networking : With a built-in HD digital tuner, non-subscription Top Box) needed. • HDMI/DVI connection HD broadcasts can be viewed with no Cable Box/Satellite receiver (Set- of your PC to this TV.
Viewing the Control Panel Buttons on the Lower-Right Part of the Panel The buttons on the lower=right panel control your TV's basic features, including the on-screen To use the more advanced features, you must use the remote control. FP-TS084 menu. SOURCE v \._._/ FP-T6374 s_Msu_ F Toggles between all the available input sources (TV, AVl, AV2, S-Video1, S-Video2, Component1, Component2, PC, HDMI1, HDMI2, or HDMI3). 4 Press to confirm a selection.
Viewing the Connection Panel Rear Panel Jacks Use the rear panel jacks to connect A/V components that will be connected continuously, such as VCR or DVD players. For more information on connecting equipment, see pages 9-14. The product color and shape may vary depending on the model. @ ® O POWER IN Connect the supplied power cord. O DIGITALAUDIO OUT (OPTICAL) Connect to a Digital Audio component. O 0 ANT 1 IN(AIR)/ANT 2 IN(CABLE) Uses a 75D CoaxiaI connector for an Air/Cable Network.
Remote Control You can use the remote control up to a distance of about 23 feet from the TV. When using the remote, always point it directly at the TV. You can also use your remote control to operate your VCR, Cable box, DVD player, or Set-Top Box. O POWER Turns the TV on and off. O NUMERIC BUTTONS Press to directly select a channel. Press to select additional channels (digital and analog) being broadcast by the same station.
Installing Batteries in the Remote Control 1 Lift the cover at the back of the remote control upward as shown in the figure. 2 Install twoAAAsize batteries. _-- Make sure to match the "+" and "-" ends of the batteries with the diagram inside the compartment. _,_ Do not mix battery types, i.e. alkaline and manganese. 3 _-- Close the cover as shown in the figure. _-- Remove the batteries and store them in a cool, dry place if you won't be using the remote control for a long time.
Connecting Cable TV To connect to a cable TV system, follow the instructions Cable without 1 a Cable Box Ptug the incoming cable into the ANT 2 IN(CABLE) terminal _-- Because this TV is cable-ready, unscrambled cable channels. Connecting 1 on the back of the TV. you do not need a cable box to view to a Cable Box that Descrambles AI! Channels Find the cable that is connected to the ANT OUT terminal on your cable box. This terminal 2 below. might be labeled "ANT OUT", "VHF OUT" or simply, "OUT".
Connecting a VCR Video Connection These instructions assume that you havealready connected your TV to an antenna or a cable TV system (according to the instructions on pages 9~10). Skip step 1 if you have not yet connected to an antenna or a cable system. 1 Unplug the cable or antenna from the back of the TV. 2 Connect the cable or antenna to the ANT IN terminal on the back of the VCR.
Connecting a Camcorder The side panel jacks on your TV make it easy to connect a ¢amcorder to your TV. They allow you to view the ¢amcorder tapes without using a VCR Connect a Video Cable (or S-Video Cable) between the AV IN 2 [VIDEO] (or S-VIDEO)jack on the TV and the VIDEO OUT jack on the Camcorder. TV Side Panel / ¢--E-'l Connect Audio Cables between the AV IN 2 [L-AUDIO-R] jacks on the TV and the AUDIO OUT jacks on the Camcorder. Connecting EJ..v,.eo Cob,e(.o, o..p,,e._ I ....
Connecting a DVD Player/Cable Box/Satellite This connection can only be made if there provide the highest quality picture. Connect an HDMI Cable between the HDMI IN 2 on the TV and the HDMI OUT on DVD Player receiver (Set-Top Box) via HDMI is an HDMI Output jack on the external device. / Cable Box/Satellite receiver (Set-Top Box) This connection will TV Rear Panel the DVD Player/Cable Box/ Satellite receiver (Set-Top Box). _IHDMI Cable (Not supplied) What is HDMI? .
Connecting a Digital Audio System The rear panel jacks on your TV make it easy to connect a Digital Audio System to your TV. 1 Connect an Optical Cable between the DIGITAL AUDIO OUT (OPTICAL) jacks on the TV and the Digital Audio Input (OPTICAL) jacks on the Digital Audio System. When a Digital Audio System is connected to the "DIGITAL AUDIO OUT (OPTICAL)" jack: Decrease the gain (volume) of the TV, and adjust the volume level with the system's volume control.
Operation Turning the TV On and Off i Press the POWER button on the remote control. You can also use the POWER button on the TV. i It may take a while when your TV starts. Plug & Play Feature When the TV is initially powered On, basic settings 1 proceed automatically and subsequently: Press the POWER button on the remote control. The message displayed. Menu language, Shop Mode, Channels and Time will be set.
The TV will begin memorizing all of the available channels. After all the available channels are stored, the Auto program menu reappears. Press the ENTER button when channet memorization The Clock Mode menu is automatically displayed. is complete. _-- To stop the search before it has finished, press the ENTER button with Stop selected. Press the A or T button to select Manual if you want to set the current time manuaIty, then press the ENTER button. Set current date and time. is displayed.
If_ou want to reset this feature... 1 Press the MENU button to display the menu. Press the A or _' button to select Setup, then press the ENTER button. 2 Press the ENTER button to select Plug & Play. For further details on setting up options, refer to the page 15~16. _-- The Plug & Play feature is only available in the TV and DTV mode. Changing Channels Usin the Channel Buttons Press the CH/x, _- _the 1 or CN v button to change channels. When you press the CH z_.
Adjusting the Volume Usin 1 the Volume Buttons Press the VOL + or VOL - button to increase or decrease the volume. I!!'-----"--------------------f_l,_ _ _ C_ .........ll l!! 'Jl _the Mute Button At any time, you can cut off the sound using the MUTE button. 1 // == [_____[L_______=____ .......______ ......JJ_____J The word "Mute" wilt appear in the tower-left 2 ==//....... Press MUTE and the sound cuts off. corner of the screen.
Memorizing the Channels Your TV can memorize and store all of the available channels for both air and cable channels. After the available channels are memorized, use the CH ,,_ or CH v button to scan through the channels. This eliminates the need to change channels by entering the channel digits. There are three steps for memorizing channels: selecting a broadcast source, memorizing the channels (automatic) and adding and deleting channels (manual).
Setting Up Your Remote Control After your remote control has been properly set up, your remote contro! can operate in five different modes: TV, VCR, Cable, DVD, or Set-Top Box. Pressing the corresponding button on the remote control allows you to switch among these modes, and control whichever piece of equipment you choose. > The remote control might not be compatible with all DVD Players, VCRs, Cable boxes, and Set-Top Boxes. Settina U_ the Remote to O_erate Your VCR 1 Turn off yourVCR.
the Remote to Operate Your DVD 1 Turn off your DVD. 2 Press the DVD button on your TV's remote control. 3 Press the SET button on your TV's remote control. 4 Using the number buttons on your remote control, enter three digits of the DVD code isted on page 24 of this manual for your brand of DVD. Make sure you enter three digits of the code, even if the first digit is a "0'. (If more than one code is listed, try the first one.) 5 Press the POWER button on the remote control.
Remote Control Codes VCR Brand SAMSUNG Code 000001 002003 004005 077078 079 Brand MITSUBISHI Code 019034 041046 ADMIRAL AIWA AKAI AUDIO DYNAMICS 020 025 004027 032 007026 MONTGOMERYWARD MTC MULTITECH NEC 020 002025 002005 025038 007008 018026037 062064 BELL&HOWELL BROKSONIC CANDLE CANON CITIZEN COLORTYME CRAIG 018 022 002003 006008 015055 021056 002003 006008 015055 007 002024 OPTIMUS PANASONIC PENTAX PENTEXRESEARCH+ PHILCO PHILIPS PIONEER 020 021056 071072 01904I 075 008 021056 059 021080 01902
CABLE BOX Brand SAMSUNG Code 0% 001002003 004 005006007 Brand REGENCY Code 015 023 GI HAMLIN HITACHI JERROLD 041 003 02403t 025 030 038 039 SA SCIENTIFICATLAN SPRUCER STARGATE2000 042 043 042 043 022 036 MACOM MAGNAVOX OAK PANASONIC PHILIPS PIONEER RCA 025 030 019 023028 026 003 022027037 044 019 021023028 004 018020044 014 022040 SYLVANIA TEXSCAN TOCOM UNIVERSAL VlEWSTAR WARNERAMEX ZENITH 016 016 032 033 034 019 021023 028 046 017 029035 037045 REGAL 003 8AMSUNG SET-TOP BOX Product Groundwave
8AMSUNG DVD Product DVD Code 000001002 Product HomeTheaterVCRCOMBO Code 014 015016 DVDR BDRecord VCR COMBO VCR Record 003004 005006 007008009 010 011 012 HDDRecordCOMBO TWINTRAYCOMBO STB DVDCOMBO DVD Receiver 017 018 019 020 DHRCOMBO 013 AVReceiver 021 DVD Brand ANAM AUDIOVOX AUDIOLOGIC ANABA APEXDIGITAL AIWA BROKSONIC BLAUPUNKT B&K CURTISMATHES CYBERHOME CLARION CIRRUS CINEVIStON DAEWOO DENON FARENHEIT FISHER GPX GO VIDEO GE GREENHILL HITACHI HITEKER HOYO HARMAN/ KARDON IRT tNTEGRA JBL JVC JATO
To Select the Source Use to select TV or other external input sources such as DVD players or Cable Bo×/Satellite receivers (Set-Top Box) connected to the TV. Use to select the input source of your choice. 1 Press the MENU button to display the menu. Press the A or _' button to select input, then press the ENTER button. 2 Press the ENTER button to select Source List. Press the A or _' button to select the signal source, then press the ENTER button.
i Picture Control ] Using Automatic Picture Settings Your new Plasma TV gives you optimal control over the picture you're watching. You can change the screen size, improve the image quality, even watch something else without turning off what you're currently watching. Please be aware that the best picture on this TV will be obtained from High Definition (HD) sources such as Digital cable or DVD players.
5 Press the A or _' button to select Color Tone, then press the ENTER button. Press the & or _' button to select Cool2, Cool1, Normal, then press the ENTER button. _-- When the picture mode is set to Dynamic cannot be selected. Resetting 7 the Picture Settings or Standard, Warm1, or Warm2, Warm1 and Warm2 to the Factory Defaults Press the A or T button to select Reset, then press the ENTER button. Press the A or _' button to select OK, then press the ENTER button. Press the EXIT button to exit.
Changing the Screen Size Occasionally, you may want to change the size of the image on your screen. Your TV comes with six screen size options, each designed to work best with specific types of video input. Your cable box or satellite receiver may have its own set of screen sizes as well. in general you should view the TV in 16:9 mode as much as possible. 1 Press the MENU button to display the menu. Press the ENTER button to select Picture.
Making Detailed Picture Settings Samsung's new TVs allow you to make even more precise picture settings than previous make Detailed picture settings. 1 Press the MENU button to display the menu. Press the ENTER button to setect Picture. 2 Press the A or _' button to setect Detailed button. 3 Select the desired Detailed Settings option by pressing the _, or _' button, then press the ENTER button. 4 When you are satisfied with your setting, press the ENTER button. Press the EXIT button to exit.
Ed_ Enhancement: You can emphasize xvYCC: Off/On object boundaries. Off/On Setting the xvYCC mode to On increases detail and color space when watching movies from an external device (ie. DVD player) connected to the HDMI or Component IN jacks.You must set the Picture Mode to Movie to enjoy this feature. _-- The xvYCC function works only in Component or HDMI mode. Active Color if you turn on this option, the blue and green colors will be more vivid. 1 Press the MENU button to display the menu.
Selecting the Film Mode Automatically senses and processes film signals from all sources and adjusts the picture for optimum 1 Press the MENU button to display the menu. Press the _, or T button to select Setup, then press the ENTER button. 2 Press the _, or T button to select Film Mode, then press the ENTER button. 3 Press the _, or T button to select Off or On, then press the ENTER button. quality. Press the EXIT button to exit.
Viewing Picture-in-Picture This product has one built-in tuner, which does not allow PiP to function in the same mode. For example, you cannot watch one TV channel in the main screen, and a different one in the PiP screen. Please see 'PiP Settings' below for details. You can use the PiP feature to simultaneously watch two video sources. (See page 37 to select the PiP picture sound.) _-- While the V-Chip is in operation, the PIP function cannot be used.
the Position of the PiP Window Press the A or T button to select Position, then press the ENTER button. Press the A or T button to select the desired PIP window position, then press the ENTER button. _,_ In Double Window ( _ be selected. ) and Double Wide ( _ ) modes, Position cannot _,_ If the PIP window is set to Double Window ( r_ ) or Double Wide ( _ ) mode, the screen size or alignment may slightly differ depending on the signal type.
i Sound Control ] Using Automatic Sound Settings Your TV has automatic sound settings ("Standard", "Music", "Movie", "Speech", and "Custom") that are preset at the factory. Or you can select "Custom", which automatically recalls your personalized sound settings. 1 Press the MENU button to display the menu. Press the _, or T button to select Sound, then press the ENTER button. 2 Press the ENTER button to select Mode. Press the A or T button to setect Standard, Music, Movie, Speech, ENTER button.
Setting the TruSurround ×T TruSurround XT is a patented SRS technology that solves the problem of playing 5.1 multichannel content over two speakers. TruSurround delivers a compelling, virtual surround sound experience through any two=speaker playback system, including internal television speakers, it is fully compatible with al! multi channel formats. 1 Press the MENU button to display the menu. Press the A or _' button to select Sound, then press the ENTER button.
Choosing a IVlulti-Channel Sound (IVlTS)Track =Analog Depending on the particular program being broadcast, you can listen to Mono, Stereo or SAP. Multi-Track Sound 1 Press the MENU button to display the menu. Press the _, or _' button to select Sound, then press the ENTER button. 2 Press the _, or _' button to select Multi-Track button. 3 Press the ENTER button to select Multi-Track Sound. Press the _, or _' button to select a setting you want, then press the ENTER button.
Press the A or _' button to select Off or On, then press the ENTER button. Press the EXIT button to exit. _-_ . When Interna! Mute is set to On, Sound menus except Multi-track Options cannot be adjusted. . The left/right audio outputs and digital audio outputs (Optical) remain enabted. . The VOL +, VOL - and MUTE buttons do not operate when the Internal Mute is set to On.
i Channel Control ] Selecting the Antenna 1 Press the MENU button to display the menu. Press the _, or _' button to select Channel, then press the ENTER button. 2 Press the ENTER button to select Antenna. Press the _, or T button to select Air or Cable, then press the ENTER button. Press the EXIT button to exit. Press the ANTENNA button on the remote control to select Air or Cable. ', If the antenna is connected to ANT1 IN(AIR_ select Air and if it is connected to ANT2 IN(CABLE_ select Cable.
Press the A/_'/4/I_ ENTER button. buttons to select a channel to delete, then press the Press the A or 'V button to select Delete, then press the ENTER button to delete the channel. Press the EXIT button to exit. , P.MODE (RED) button: Press repeatedly to setect All, Added, 0r Favoritel i S.MODE (GREEN) button: Press to add al! Channels deteted. • STILL (YELLOW) button: Press to delete all channels memorized. Setting Your Favorite Channels You can set channels you watch frequently as favorites.
Viewing the Channel Lists You can display a list of all channels, added channels or your favorite channels. 1 Press the MENU button to display the menu. Press the _, or _' button to select Channel, then press the ENTER button. 2 Press the _, or T button to select Channel List, then press the ENTER button. Press the A or T button to select All, Added or Favorite, ENTER button. then press the To toggle between your all channels, add channels, or favorite channels, P.
Labeling Channels Channels can labeled so that their call letters appear whenever the channel is selected. 1 Press the MENU button to display the menu. Press the A or _' button to select Channel, then press the ENTER button. Press the A or _' button to select Name, then press the ENTER button. 2 Press the A or _' button to select the channel to be assigned a new name, then press the ENTER button.
Checking the Digital-Signal Strength Unlike analog channels, which can vary in reception quality from "snowy" to clear, digital (HDTV) channels have either perfect reception quality or you will not receive them at all. So, unlike analog channels, you cannot fine tune a digital channel. You can, however, adjust your antenna to improve the reception of available digital channels. 1 Press the MENU button to display the menu. Press the A or vf button to select Channel, then press the ENTER button.
PC Display Using Your TV as a Computer Your PC Software (Based (PC) Display on Windows XP_ The Windows display-settings for a typical computer are shown below. The actual screens on your PC wilt probably be different, depending upon your particular version of Windows and your particular video card. However, even if your actual screens look different, the same basic set-up information will apply in almost all cases. (If not, contact your computer or Video Card manufacturer.
Setting up the TV with your PC Use the Auto Adjust function to have the TV set automatically adjust the video signals it receives from the PC. The function also automatically fine-tunes the settings and adjusts the frequency values and positions. How to Auto 1 Press the MENU button to display the menu. Press the A or T button to select Setup, then press the ENTER button. Press the _, or _' button to select PC, then press the ENTER button.
Chan iginq the Screen Position You can adjust the position of the screen after connecting the TV to your PC. _,_ Change to the PC mode first. 1 Press the MENU button to display the menu. Press the A. or V' button to select Setup, then press the ENTER button. Press the A or _' button to select PC, then press the ENTER button. 2 Press the A or _' button to select Position, then press the ENTER button. 3 Press the A or T button to adjust the V-Position. Press the 4 or _ button to adjust the H-Position.
i Time Setting ] Setting the Time Setting the clock is necessary in order to use the various timer features while watching the TV. (Just press the INFO button.) _the Clock of the TV. Also, you can check the time Manually 1 Press the MENU button to disptay the menu. Press the A or T button to select Setup, then press the ENTER button. Press the _, or _' button to select Time, then press the ENTER button. 2 Press the ENTER button to select Clock. 3 Press the ENTER button to select Clock Mode.
Ojotion 2: Settingthe Clock Automatically The Clock can be set automatically if you are receiving a digital signal. 1 Press the MENU button to display the menu. Press the A or T button to setect Setup, then press the ENTER button. Press the A or _' button to setect Time, then press the ENTER button. 2 Press the ENTER button to select Clock. 3 Press the ENTER button to select Clock Mode. Press the A or _' button to select Auto, then press the ENTER button.
Sett_theOn/Off Use this feature the clock first. Timer to set the TV to turn on or off at a desired time. You must set Press the MENU button to display the menu. Press the A or T button to select Setup, then press the ENTER button. Press the A or T button to select Time, then press the ENTER button. Press the A or T button ENTER button. The timer Press the h, or T button next step. Set other items to select Timer1, Timer2,or Timer& then press the menu is displayed.
Function Description Selecting a Menu Language 1 Press the MENU button to display the menu. Press the A or _' button to select Setup, then press the ENTER button. Press the A or _' button to select Language, then press the ENTER button. 2 Press the A or _' button to select the appropriate or Frangais, then press the ENTER button. language: English, Espa6ol, Press the EXIT button to exit. Using the Game Mode When connecting to a game console such experience by selecting game menu.
Viewing Closed Captions (On-Screen Text Messages) - Digital The Digital Captions function operates on digital channels. 1 Press the MENU button to display the menu. Press the _, or T button to select Setup, then press the ENTER button. 2 Press the _, or T button to select Caption, 3 Press the ENTER button to select Caption. Press the A or T button to select On, then press the ENTER button. 4 Press the A or T button to select Caption Mode, then press the ENTER button.
Viewing Closed Captions (On-Screen Text Messages) -Analog The Analog Caption function operates in either analog TV channel mode or external signal mode. (Depending the broadcasting signal, the Analog Caption function may operate on digital channels.) 1 Press the MENU button to display the menu. Press the A or _' button to setect Setup, then press the ENTER button. 2 Press the A or _' button to setect Caption, 3 Press the ENTER button to select Caption.
Menu Transparency Level Adjusts the transparency of the menu screen. 1 Press the MENU button to display the menu. Press the _, or T button to select Setup, then press the ENTER button. 2 Press the _, or T button to select Menu Transparency, button. 3 Press the _, or _' button to select level, then press the ENTER button. then press the ENTER Press the EXIT button to exit. Setting the Light Effect You can turn the blue LED on the frent of yeur TV on/off.
Using the Energy Saving Feature This feature adjusts the power consumption of the unit in order to save energy. 1 Press the MENU button to display the menu. Press the A or _' button to select Setup, then press the ENTER button. 2 Press the A or _' button to select Energy Saving, button. then press the ENTER Press the A or T button to select Off, Low, Medium, or High, then press the ENTER button. Press the EXIT button to exit. J Off: Switchesoff the Energy Saving mode. .
Reducing the Effects of Screen Burn if screen burn has occurred, you can select a white screen or scrolling to help remove screen burn artifacts. 1 Press the MENU button to display the menu. Press the _, or _' button to select Setup, then press the ENTER button. 2 Press the A or T button to select Screen ENTER button. 3 Press the A or T button to select White, then press the ENTER button. Press the EXIT button to exit.
Using the V=Chip U.S.A Only Th s product s covered by the following U.S. patents : US4,930,158 US4,930,160 The V-Chip feature automatically locks out programs that are deemed inappropriate for children. The user must enter a PiN (personal ID number} before any of the V-Chip restrictions are set up or changed. _-- When the V-Chip feature is activated, the PIP features do not function. _-- V-Chip function is not available in HDMI or component mode.
How to Set up Restrictions Using "TV Parental Guidelines" First, set up a personal identification number (PIN), and enable the V-Chip. (See previous section.) Parental restrictions can be set up using either of two methods: The TV guidelines or the MPAA rating. 1 Press the MENU button to display the menu. Press the A or _' button to select Setup, then press the ENTER button. 2 Press the A or _' button to select V-Chip, then press the ENTER button. The message Enter PIN will appear.
How to set the FV, D, L, S and V sub-ratings. First, select one of these TVRatings: TV-Y, TV-Y7, TV-G, TV-PG, TV-14, or TV-MA (See Step 4), and press the ENTER button. The "@" symbol will be displayed for each sub-rating. While "_" is selected, press the I_ button to go to a sub rating. Press the ENTER to block the sub rating. To select a different TV-Rating, press the A or _' button and then repeat the process. Press the EXIT button to clear all the screens.
How to Set u_ Restrictions Usin "Canadian En liah" for Canada Models_ 1 Press the MENU button to display the menu. Press the A or T button to select Setup, then press the ENTER button. 2 Press the A or T button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. 3 The V-Chip screen will appear. Press the _, or _' button to select Canadian English, then press the ENTER button Press the _, or T button to select an appropriate restriction.
How to Set u Restrictions Usin "Canadian French" {for Canada Models) 1 Press the MENU button to display the menu. Press the A or _' button to select Setup, then press the ENTER button. 2 Press the A or _' button to select V-Chip, then press the ENTER button. The message Enter PiN wilt appear. Enter your 4 digit PIN number. 3 The V-Chip screen will appear. Press the A or _' button to select Canadian French, then press the ENTER button. Press the A or _' button to select an appropriate restriction.
Usin theV-Chi for D'H'tal channels Parental restriction information can be used while watching DTV channels. 1 Press the MENU button to display the menu. Press the _, or T button to select Setup, then press the ENTER button. 2 Press the A or T button to select V-Chip, then press the ENTER button. The message Enter PIN will appear. Enter your 4 digit PIN number. 3 The V-Chip screen wilt appear. Press the _, or T button to select Downloadable U.S. Rating, then press the ENTER button.
Upgrading the Software Samsung may offer upgrades for your TV's firmware in the future. Please contact the Samsung call center at 1-8O0-SAMSUNG to receive information about downloading upgrades and using a USB drive. Upgrades will be possible by connecting a USB drive to the USB port located on the side of your TV. / 1 Insert a USB drive containing on the side of the TV. 2 Press the MENU button to display the menu. Press the A or _' button to select Setup, then press the ENTER button.
W|SEL|NK ] Using the WISELINK Function This function enables you to view and listen to photo (BASELINE, JPEG) and audio files (MP3} saved on a USB Mass Storage Class device. Insert a USB device containing JPEG and/or MP3 files into the WISELINK jack (USB jack) on the side of the TV. TV Side Panel USB (Not supplied) @ S-VIDEO @ 0 ,o;o _-- WISELINK only supports USB Mass Storage Class devices (MSC). MSC is a Mass Storage Class Bulk-Only Transport device.
Using the WISELINK Mode 1 Press the MENU button to display the menu. Press the ENTER button to select input. Press the A or _' button to select WISELINK, then press the ENTER button. Press the A or _' button to select a corresponding the ENTER button. memory device, then press A menu for selecting the Photo or Music files or setup function on a selected memory device will be displayed. The WISELINK menu differs depending connected to TV.
Using the Photo (JPEG) List You can play back the ,JPEG files saved on a memory device in various ways. 1 After switching the mode to WISELINK, inserted. (Refer to page 63) 2 Press the 41 or _ button to select Photo, then press the ENTER button. JPEG files and existing folders are displayed. Press the A/T/4/I_ select the memory device that you have buttons to select a file, then press the ENTER button. :_ Pressing the button over a photo icon displays the currently selected photo in full screen.
O_ptions Menu Slide Show: Starts a slide show. (Refer to Viewing a Slide Show on page 66) Rotate: You can rotate images in full screen mode. Images are rotated in the order of 90 °, 180 °, 270 ° and 0 ° (original state). (Refer to Rotating on page 88) _,_ You cannot save a rotated image. _-- It may take tong time to rotate the large-size file. Zoom: You can zoom into images in full screen mode. Images are zoomed in the order of X2, )(4 and X1 (original (Refer to Z.ooming-ln on page 69) size).
Viewin_qa Slide Show 1 After switching the mode to WISELINK, inserted. (Refer to page 63) 2 Press the _ or _ button to select Photo, then press the ENTER button. JPEG files and existing folders are displayed. 3 Press the INFO button to display the option (Slide Show, Cancel file). 4 Press the A or T button to select Slide Show, then press the ENTER button. select the memory device that you have the selected The Slide show displays all JPEG files in the selected folder at a preset speed.
_the Menu during a Slide Show Slide Show Speed: Select to control the Slide Show Speed. Each time the ENTER button is pressed, the speed changes repeatedly. (Normal _ Slow _ Fast) Background Music: Select to choose whether you want to play MP3 files during a slide show. Each time the ENTER button is pressed, the background music activation changes repeatedly. (On -_ Off) Background Music Setting: While the slide show is in progress, MP3 files and folders under the same directory are displayed.
Rotatin_ 1 After switching the mode to WISELINK, inserted. (Refer to page 63) select the memory device that you have 2 Press the 4 or _ button to select Photo, then press the ENTER button. JPEG files and existing folders are displayed. 3 Press the A/T/4/_ buttons to select a file, then press the ENTER button. Pressing the button over a photo icon shows the currently selected photo in full screen. Press the INFO button to display the option (Slide Show, Rotate, Zoom, List).
Zooming-In 1 After switching the mode to WISELINK, inserted. (Refer to page 63) 2 Press the 4 or !1_button to setect Photo, then press the ENTER button. JPEG files and existing folders are displayed. 3 Press the A/_'/_t/I_ buttons to select a file, then press the ENTER button. Pressing the button over a photo icon shows the currently selected photo in full screen.
Using the Music (MP3) List You can play back the MP3 files saved on a memory device in various ways. 1 After switching the mode to WISELINK, inserted. (Refer to page 63) select the memory device that you have 2 Press the 4 or I_ button to select Music, then press the ENTER button. MP3 files and existing folders are displayed. Press the _, or _' buttons to select a file to be played, then press the ENTER button.
Using the Setup Menu Setup displays the user settings of the WISELINK menu 1 After switching the mode to WISELINK, inserted. (Refer to page 63) setect the memory device that you have 2 Press the 4 or _- button to select Setup, then press the ENTER button, The Setup menu is displayed. 3 Press the A or _' button to select an item you want, then press the ENTER button. 4 Press the A or _' button to select the option, then press the ENTER button.
About Anynet+ ] What is Anynet+? Anynet+ is a function that enables you to control all connected Samsung TV's remote. Samsung devices that support Anynet+ with your Connecting Anynet + Devices The Anynet+ system can be used only with Samsung devices that have the Anynet+ Samsung device has this feature, check if there is an Anynet+ logo on it. feature.
Setting Up Anynet + The following settings help set the Anynet + functions. To use the An net+ Function, An net+ HDMI-CEC must be set to On 1 Press the Anynet + button. Press the A or _' button to setect Setup, then press the ENTER button. 2 Press the ENTER button to select Anynet+ ENTER button. (NDMI-CEC), then press the Press the A or _' button to select On, then press the ENTER button. _-- The Anynet+ (HDMI-CEC) function is enabled.
_net + Menu The Anynet + menu changes depending ......... on the type and status of the Anynet + devices connected to the TV. Anynet + Menu Description View TV Switches from Anynet + to TV broadcast mode. Record Starts a recording. (This menu works only for a device supporting recording.) (Device_Name) Menu Shows the menu of the connected device. Example: When a DVD Recorder is connected, the DVD Recorder's title menu appears.
Listening through a Receiver (Home theater) You can listen to sound through a receiver instead of the TV speaker. 1 Press the Anynet + button. Press the A or _' button to setect Receiver, then press the ENTER button. 2 Press the 4 or I_ button to select to On, then press the ENTER button. Now you can tisten to sound through the receiver. 3 Press the EXiT button to exit. _,_ When the receiver (home theater) is set to On, you can hear sound output from the TV's Optical jack.
i Appendix ] Troubleshooting if the TV seems to have a problem, first try this list of possible problems and solutions. if none of these troubleshooting tips apply, call your nearest Samsung service center. Problem Poor picture quality. Poor sound quallt_ No picture or sound. Possible Solution Try another channeI. Adjust the antenna. , Check a!l wire €_0nnec!ions. Try another channel Adjust the antenna: Try another channel. Press the SOURCE button. Make sure the TV is plugged in.
Auto WalPmount adjustment (Sold separately) Once the auto wall mount is installed, the position of your TV can be easily adjusted. Auto Wall-Mount TV Rear Panel I1 f _)1 J EX-LINK Cable (Not i supplied) the menu 1 Press the MENU button to display the menu. Press the A or _r button to select Setup, then press the ENTER button. 2 Press the A or T button to select Wall-Mount ENTER button. 3 Adjust to the desired position using the _,/T/4/_- Adjustment, then press the buttons.
Wall Mount Kit Specifications ( VESA ) Instalt your wall mount on a solid wall perpendicular to the floor. When attaching to other building materials, please contact your nearest dealer. If installed on a ceiling or slanted walt, it may fail and result in severe personat injury.
How to assemble the Stand=Base (dependingon the model) Using the 6 screws for securing the stand base and the monitor, firmly attach the monitor to the stand base. When mounting your TV on a wall, install the cover (O) on the stand-base using two screws. (The exterior of the set may be different from the picture.) FP-TS084 FP-T6374 Warning Firmly secure the stand to the TV before moving it, as the stand may fall and could cause serious injury. _-- Two or more people should carry the TV.
Dimensions (FP-T5084) x # , \ I TOP VIEW / I FRONT VIEW JACK PANEL DETAIL 2 1/4"H x 18 3/4"W @ 5 3/4" UP FROM BOTTOM SIDE VIEW REAR VIEW NOTE; All drawings not necessarily to s_le Some dime_,sions a_e subjecf to c]_ange without prier notice Refe any _o dimensions oar£en ry Not on each responsible mi_ prior to perforating or typoqfaphic_l prin_ed enom @ 2007 Sams_mg Elect onics Amedca Inc or
Dimensions (FP-T6374) J \ 356 TOP VIEW FRONT ViEW 00 JACK PANEL DETAIL 2 1/4"H x 18 3/4"W @ 5 3/4" UP FROM BOTTOM 34 /2 ! I '-'-' ! D[- SIDE VIEW _'°°° [ i J Y Jl I i it _ J REAR VIEW NOTE: All drawings r_otnecessarily to sc
