User Manual

13
English
03 Basic Features
Satellite System Setup
The PIN input screen appears. Enter your 4 digit PIN number.
Satellite System Setup is available when Antenna is set to
Satellite. Before running Auto Store, set Satellite System Setup.
Then channel scan is run normally.
Satellite Selection: ■ You can choose the satellites for this TV.
LNB Power (Off / On) ■ : Enables or disables the power
supply for the LNB.
LNB Settings ■ : Configures the outdoor equipment.
Satellite: Selects the satellite for receiving digital
broadcasts.
Transponder: Selects a transponder from the list or adds a
new transponder.
DiSEqC Mode: Selects DiSEqC mode for the selected LNB.
Lower LNB Oscillators: Sets the LNB oscillators to a lower
frequency.
Upper LNB Oscillators: Sets the LNB oscillators to a higher
frequency.
Tone 22 khz (Off / On / Auto): Selects the Tone 22 kHz
depending on the LNB type. For a universal LNB it should
be Auto.
Signal Quality: Display the current status of broadcasting
signal.
Positioner Settings ■ : Configures the antenna positioner.
Positioner (Off / On): Enables or disables the positioned
control.
Positioner Type (USALS / DiSEqC 1.2): Sets the
positioned type between DiSEqC 1.2 and USALS(Universal
Satellite Automatic Location System).
My Longitude
–
: Sets the longitude for my location.
My Latitude
–
: Sets the latitude for my location.
Satellite
–
Longitude Settings: Sets the longitude of user
defined satellites.
User Mode: Sets the position of satellite antenna according
to each satellite. If you store the current position of satellite
antenna according to a certain satellite, when the signal of
that satellite is needed, the satellite antenna can be moved
to pre-populated position.
Satellite
–
: Selects the satellite to set the position for.
Transponder
–
: Selects a transponder from the list for
signal reception.
Moving Mode
–
: Selects the movement mode between
discrete and continuous movement.
Step Size
–
: Adjusts the step size degrees for the antenna
rotation. Step Size is available when Moving Mode is set
to Step.
Go to Stored Position
–
: Rotates the antenna to the
stored satellite position.
Antenna Position
–
: Adjusts and stores the antenna
position for the selected satellite.
Store Current Position
–
: Stores current position as the
selected positioner limit.
Signal Quality
–
: Display the current status of
broadcasting signal.
Installer Mode: Sets limits to the scope of movement of
satellite antenna or reset the position. Generally, installation
guide uses this function.
Limit
–
Position (East / West): Selects the direction of
the positioner Limit.
Antenna Position
–
: Adjusts and stores the antenna
position for the selected satellite.
Store Current Position
–
: Stores the current position
as the selected positioner Limit.
Go to Zero
–
: Moves the antenna to the reference
position.
Reset Positioner Limit
–
: Allows the antenna to rotate
over the full arc.
Reset All Setting (OK / Cancel) ■ : All satellite settings will
be reset to the initial values.
¦ Editing channels
Channel Manager Option Menu
(in Channel Manager)
1. Select a channel and press the TOOLS button.
2. Edit the channel name or number using the Edit
Channel Name or Edit Channel Number menu.
Edit Channel Name ■ (analogue channels only): Assign
your own channel name.
Edit Channel Number ■ (digital channels only): Edit the
number by pressing the number buttons desired.
Other Features ¦
Cable Search Option
(depending on the country)
Sets additional search options such as the frequency and
symbol rate for a cable network search.
Freq.Start / Freq.Stop ■ : Set the start or stop frequency
(differs in each country)
Modulation ■ : Displays available modulation values.
Symbol Rate ■ : Displays available symbol rates.
BN68-02791AEGH_00Eng.indb 13 3/9/2010 1:06:14 PM