SyncMaster 220TN Install driver Install programs
Notation Failure to follow directions noted by this symbol could result in bodily harm or damage to the equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Ground to prevent an electric shock Power When not used for extended period of time, set your computer to DPM. If using a screen saver, set it to active screen mode. The images here are for reference only, and are not applicable in all cases (or countries).
This may cause electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. This may cause electric shock or fire. Use only a properly grounded plug and receptacle. An improper ground may cause electric shock or equipment damage. ( Class l Equipment only.) Insert the power plug firmly so that it does not come loose. A bad connection may cause fire. Do not excessively bend the plug and wire nor place heavy objects upon them, which could cause damage.
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. This may cause electric shock or fire. Installation Be sure to contact an authorized Service Center when installing your set in a location with heavy dust, high or low temperatures, high humidity, and exposed to chemical substances and where it will be operated for 24 hours such as at airports, train stations etc.
Otherwise, this may cause fire. Keep any heating devices away from the power cable. A melted coating may cause electric shock or fire. Do not install the product in places with poor ventilation, for instance, a bookshelf, closet, etc. Any increase in the internal temperature may cause fire. Put down the monitor carefully. Failing to do so may damage the monitor. Do not place the monitor face down. This may damage the TFT-LCD surface.
Cleaning and Using When cleaning the monitor case or the surface of the TFT-LCD screen, wipe with a slightly moistened, soft fabric. Do not spray water or detergent directly onto the monitor. This may cause damage, electric shock or fire. Use the recommended detergent with a smooth cloth. If the connector between the plug and the pin is dusty or dirty, clean it properly using a dry cloth. A dirty connector may cause electric shock or fire. Make sure to unplug the power cord before cleaning the product.
Do not remove the cover (or back). This may cause electric shock or fire. Refer to a qualified servicing company. If your monitor does not operate normally - in particular, if there is any unusual sound or smell coming from the monitor- unplug it immediately and contact an authorized dealer or the Service Center. This may cause electric shock or fire. Keep the product away from places exposed to oil, smoke or moisture; do not install inside a vehicle. This may cause a malfunction, electric shock or fire.
Do not place water containers, chemical products or small metal objects on the monitor. This may cause a malfunction, electric shock or fire. If a foreign substance enters the monitor, unplug the power cord and contact the Service Center. Keep the product away from combustible chemical sprays or inflammable substances. This may cause an explosion or fire. Never insert anything metallic into the monitor openings. This may cause electric shock, fire or injury.
To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations. Dropping the product may cause damage to the product or the person carrying it. Using the product in a location prone to vibrations may shorten the lifetime of the product or may cause the product to catch fire. When moving the monitor, turn off and unplug the power cord.
monitor screen. Look at the screen from slightly above it, and have the monitor directly in front of you. z z Tilt the monitor upwards by 10 ~20 degrees. Adjust the monitor height so that the top of the monitor is slightly below eye level. Adjust the monitor angle so that there is no reflected light on the screen.Try to maintain your arms perpendicular to your armpits. z Keep your arms level with the back of your hands. z Keep the angle of the elbow perpendicular.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have an image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate a correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Features What is a network monitor? A network monitor can be used for the same purposes as a common monitor. It also provides the functionalities of most computers, such as an Internet connection, creating documents, editing images, via a connection to the host PC over the LAN. In addition, it allows you to connect an external device (DSC, MP3, external storage media) to the USB port and play music, movies and games. It is a new concept monitor.
Contact a local dealer to buy optional items.
Keyboard (USB) Mouse (USB) Others Cleaning Cloth This is an accessory that can be added depending on the model. Your Monitor Front Touch a button lightly with your finger. MENU button [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. Adjust buttons [ ] These buttons allow you to adjust items in the menu. MagicBright™ button [ ] MagicBright™ is a new feature providing optimum viewing environment depending on the contents of the image you are watching.
buttons. 1) Custom Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the brightness and contrast by using the OSD menu. 2) Text For documentations or works involving heavy text. 3) Internet For working with a mixture of images such as texts and graphics. 4) Game For watching motion pictures such as a game. 5) Sport For watching motion pictures such as a Sport.
Rear The configuration at the back of the monitor may vary from product to product. POWER z POWER : Connect the power cord for your monitor to the POWER on the back of the monitor. RGB OUT z Connect when using it as a monitor. 2/ 2 : Connect the the USB cable. 2 of the USB monitor and a USB device with : Connect the of the monitor and the USB of the computer with the USB cable. z To use 2, you have to connect the to the PC.
z Connect when using it as a monitor. RGB IN z RGB IN :Connect the signal cable to the 15-pin, D-sub port on the back of your monitor. AUDIO IN z AUDIO IN : Connect the audio cable for your monitor to the audio port on the back of your computer. / MIC/ (Earphone jack) : Headphone connection terminal. MIC (The Microphone connection terminal) : Connect a microphone to the MIC terminal.
Connecting Cables Connect to the host PC using a LAN cable Host PC Hub LAN Cable Monitor Connect the power cord to the power terminal at the back of the monitor. Connect the mouse and the keyboard to the USB ports. Connect the LAN port on the back of the monitor and the hub. Connect the hub and the LAN port of the host PC. The host PC must have an IP address. After connecting the LAN and setting the IP address, you can view the host PC screen on the monitor.
Connect the power cord for your monitor to the POWER port on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. Use a connection appropriate for your computer. Using the D-sub (Analog) connector on the video card. - Connect the D-Sub Cable to the RGB IN port on the back of your monitor. [RGB IN] Using Macintosh - Connect the monitor and the Macintosh computer using the computer connection cable. If the monitor and the computer are connected, you can turn them on and use them.
LAN (LAN Connection Terminal) Connect the LAN cable. Connecting USB Connecting USB Turn on your monitor and PC. If you connect the cable to the connector of your monitor and the 2 cable to the 2 connector of your PC, the installation programs related to microphone and camcorder are performed automatically. You can use a USB device such as a mouse, keyboard, Memory Stick, or external hard disk drive by connecting them to the 2 port of the monitor without connecting them to the PC.
z You can connect and use a keyboard and mouse. z You can play a file from a media device. (Examples of media devices: MP3, digital camera, etc.) z You can run, move, copy or delete the files on the storage device. (Examples of storage devices: external memory, memory card, memory reader, HDD-type MP3 player, etc.) z You can use other USB devices that can be connected to a computer. z Do not disconnect the USB cable while the installation is in progress.
Monitor Mounting interface pad (Sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
What is XPe Client? An Microsoft Windows XP Embedded(XPe) client uses the Microsoft Windows XP Embedded operating system. When an XPe client is connected to a Citrix ICA server or another server that can provide the Microsoft RDP service, data for the keyboard, mouse, audio/video and display are transmitted through the network between the client and the server.
Windows XP Embedded Desktop User When a user logs in, the User Desktop appears, as shown in the figure below. The default icons that appear on the User Desktop are Citrix Program Neighborhood, Remote Desktop Connection and Internet Explorer. You can also run this connection from the Start menu. The audio volume icon, VNC server icon and system time are displayed on the User Taskbar. When logged on as a user, there are many restrictions that protect the system from incorrent user actions.
Programs - XPe Client is a client/server-based computing platform. On this platform, the client accesses the server each time it needs a program and it only receives the user interface screens from the server. Hence, various programs, such as ICA, RDP, and VNC, which are installed on a XPe Client, are used to help the client access the server and perform user tasks.
2. Type the connection name and the server name (IP address or DNS name). 3. Configure the degree of compression for the data to be sent and received, and the degree of reliability for sessions. 4. To login to the server automatically, enter your username, password and domain. If you do not enter them now, you will be prompted to enter them whenever you connect to the server.
5. You can specify the color and size of the window to be displayed. 6. If a connection succeeds, the server’s desktop appears on the client. In this step, you can make an application run automatically. 7. Click Finish to complete creating the new connection.
For more information on the ICA Client Program, visit the Citrix web site. The Remote Desktop Connection You can control a running terminal server or another computer (Windows 95 or later) remotely through a remote desktop connection. Remote Desktop - Windows XP Professional or Windows 2000/2003 Server must be installed on the computer to be controlled remotely. This computer is called a host. A remote computer running on an operating system later than Windows 95 is required.
Start a Remote Desktop Session on the Client Once you have enabled your host computer to allow remote connections and installed the client software on a Windows-based client computer, you are ready to start a Remote Desktop session. You must first establish a virtual private network connection or remote access service connection from your client computer to your host computer. 1. Click Start, point to Programs, and then click Remote Desktop Connection. Or double-click the Remote Desktop Connection icon.
- Display: The Remote Desktop Connection sends and receives compressed screen data. If you set the resolution and color quality to the high option, the speed may become slow. - Local Resource: Specify whether to use the hard disks and ports.
- Programs: Specify whether to display the Desktop or run an application whenever you are connected. The default is ‘Desktop’. - Experience: You can select your connection speed, and select and share environmental options.
4. Click Connect. The Log On to Windows dialog box appears. 5. In the “Log On to Windows” dialog box, type your username, password, and domain (if required), and then click OK. The Remote Desktop window will open and you will see the desktop settings, files, and programs that are on the host computer. For more information on Remote Desktop Connections, visit the Microsoft web site.
Internet Explorer A XPe Client includes Internet Explorer. This program is permitted for all users. For more information on Internet Explorer, visit the Microsoft website. Enhanced Write Filter Enhanced Write Filter (EWF) protects a flash volume from write access and consequently, preserves the durability of the flash device. EWF provides read and write access through a cache to the client instead of allowing direct access to a flash volume. If EWF is activated, data is not stored to the flash.
enabled. After restarting your computer, the configurations and file system information for the client are written to a cache. You can also perform this operation by entering “ewfmgr.exe c: enable” at the command prompt and restarting your computer. Disable disk write protection and restart your computer - This item is activated when the EWF is running. If this item is selected, the current states of the client (saved in a cache) are saved to a flash volume and the EWF is disabled.
The C drive is used for the system. If there is less than 3MB of free space available, the client OS cannot operate. Therefore, always ensure that there is a sufficient amount of free space available. EWF can help maintain available space by preventing the C drive being written to directly. D Drive If the size of the flash memory is larger than 1 GB, the D drive (that is, the flash memory) is used as temporary file storage.
The XPe Client provides a recovery function which allows you to revert to a backed up system when encountering a serious problem. You can back up an OS image which is working normally to USB memory or the PXE server.
What is SYNCON? List of Features A thin client (computer) with an integrated LCD monitor which has the embedded VoIP(Voice Over Internet Protocol) video call function.
3. In the Local Area Connection Properties window, select Internet Protocol (TCP/IP) and click on Properties. 4. Select Use the following IP address and Use the following DNS server addresses in the General tab in the Internet Protocol (TCP/IP) Properties, enter an IP address and click the OK button as shown below. To use a fixed IP address, consult your network administrator. Checking your Pc’s IP Address Check the IP address of your PC.
1. Click Start and Run. 2. In the Run window, type 'cmd' and click OK. 3. If the following screen appears, type 'ipconfig' and press the Enter key on the keyboard. The current IP address of your PC will be displayed. If the network connection is unstable or the LAN cable is disconnected, the IP address of the PC will not be displayed.
1. The main menu allows you to navigate the basic functions of SYNCON sequentially. (In addition, you can right-click the opposite party or group to start a conversation and use the functions available in the displayed menu.) 2. Displays the username for the Instant Message and Call functions. 3. Shows the elapsed video call time. (This only appears when a video call is in progress.) 4. You can view your phonebook and call history. 5. Directly enter the IP address to call. 6.
Call History Screen 1. Displays the outgoing, incoming, and missed calls. They are sorted in the order of the time that the call was made. 2. Displays the time of calls made. (Outgoing calls) 3. Displays the time of missed calls. (Missed calls) 4. Displays the time of calls received. (Incoming calls) SYNCON Menus Main Log Out - Logs out from the SYNCON system. The Log Out function may be restricted depending on whether the current mode is Server or Non-Server mode.
Mute - Using this function, you can mute the audio data of a video call. (You can suspend a video call depending on your requirements.) Disconnect - Disconnects an existing call. Call - Makes a call to the opposite party. Send Instant Message - Sends a message to the opposite party. Office Sharing - Allows you to share office files with persons you are chatting to. Tools You can add, edit or delete a person or group and check the IP address of a registered person.
Delete All - Deletes all Call history entries. Settings You can configure the basic SYNCON environment using the Tools > Settings menu item. General 1. General Settings 2. When checked, SynCon starts automatically when Windows starts. 3. When checked, your password is entered automatically in the Login screen. 4. When checked, your SynCon is logged into the SynCon system automatically. The General Settings may be restricted depending on whether the current mode is Server or Non-Server mode.
User Info 1. User Information Settings 2. This sets the name that appears when you are using the nstant Message or Call function. 3. You can check the IP address of your PC. Video 1. Video Settings 2. Set the video size. 3. Set the amount of video data transmitted per second. 4. Set the amount of multimedia data transmitted per second. 5. Set the video aspect ratio. If you have changed the Size to CIF/4CIF, you have to exit and then restart the SYNCON program. Otherwise the program may malfunction.
Camera/MIC 1. Camera/MIC Settings 2. Set the transmission type. 3. Set the brightness and contrast for the camera. 4. PIP Screen Location: Set the location of the PIP screen. (PIP Screen Off, Top Left, Top Right, Bottom Left, Bottom Right) Some functions of the Camera/MIC Settings may be restricted depending on whether the current mode is Server or Non-Server mode. About MCU z MCU is a device used for video conference calls.
Call Control 1. Call Control Settings 2. When checked, call waiting is enabled. 3. When the person being called cannot answer the phone, it enables the call to be forwarded to another user. If you click the checkbox, the Browse item will be activated. 4. The phone number for the Call Forward function is automatically determined and it cannot be specified directly by a user. 5. If you click Browse, a dialog box is opened. - Select a number and click OK. The selected number is displayed in input field 4.
3. Fix Ratio Button You can fix the aspect ratio of the video window when resizing it using this button. 4. PIP (Picture In Picture) Button You can set up PIP (Picture In Picture) using this button. 5. AV Mute Button Using this button, you can mute the audio of a call. Once the AV Mute button is pressed, you can only use this button again after 3 seconds. 6. Size Shows the resolution to be transmitted for the user you are talking with. (CIF/4CIF) 7.
and select Call from the displayed menu. 3.Select the person to video call and select Call from the Actions menu in the SYNCON main screen. If the opposite party does not accept the call or is not connected to SYNCON, you cannot hold a video call. Receiving a Call 1. If the call rings while you are connected to SYNCON, click the Connect button. The video call will be connected. If you do not want to receive a call, click the Reject button.
1. Select 2 or more users to talk to in the SYNCON Phonebook screen by dragging the users with the mouse. Right-click over them and select Conference Call to make a conference call with 2 or more users. 2. You can make a conference call by selecting 2 or more users to talk to by dragging the users with the mouse and selecting [Actions] > [Conference Call] from the pop-up menu that appears when right-clicking. A conference call supports up to 5 users besides yourself.
3. The Office Sharing window as shown in the figure below is displayed until the opposite party accepts sharing the office file. If you click Cancel, sharing the office file is cancelled. File sharing can be activated by selecting Office Sharing from the Actions menu in the SYNCON main screen when a video call is connected to the opposite party.
Exiting Office Viewer 1. Click the Close button of the Office Viewer. 2. The Disconnect window is displayed as shown in the figure below. Click OK. The user who shared the file can exit Office Viewer.
1. Select Add Person from the Tools menu. 2. In the Add Person window, enter the information for the person you wish to call and click OK. 3. You can check that the person is added to the phonebook.
You can add a person using the menu displayed when right-clicking on the Phonebook screen. Adding a Group Entry 1. Select Add Group from the Tools menu. 2. In the Add Group window, enter a group name and click OK.
3. You can check that the group is added to the phonebook. You can add a group using the menu displayed when right-clicking on the Phonebook screen.
1. Select and right-click the entry you wish to delete and select Delete from the displayed menu. 2. Click OK. You can delete an entry by clicking on it and selecting Delete from the Tools menu.
1. Select and right-click the group entry you wish to delete and select Delete Group from the displayed menu. 2. Click OK. You can delete a group entry by clicking on it and selecting Delete Group from the Tools menu.
1. Select and right-click the entry you wish to edit and select Edit from the displayed menu. 2. In the Edit Person window, change the information and click OK. You can edit an entry by clicking on it and selecting Edit from the Tools menu. Renaming a Group 1.
menu. 2. Change the group name and click OK. 3 . The group's name is changed. You can rename a group entry by clicking on it and selecting Edit Group from the Tools menu. Viewing the Information for a Person 1. Select and right-click an entry and select Info from the displayed menu.
2. The Info window displays the information for the selected person. You can view the information for a person by clicking on that entry and selecting Info from the Tools menu.
Monitor Driver When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown below. Internet web site :http://www.samsung.com/ (Worldwide) http://www.samsung.com/monitor (U.S.A) http://www.sec.co.kr/monitor (Korea) http://www.
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Monitor driver installation is completed. Installing the Monitor Driver (Manual) Windows Vista | Windows XP | Windows 2000 | Windows ME | Windows NT | Linux Microsoft® Windows Vista™ Operating System Insert your Manual CD into your CD-ROM drive. Click (Start) and "Control Panel".
This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click "Update Driver…" in the "Driver" tab. Check the "Browse my computer for driver software" checkbox and click "Let me pick from a list of device drivers on my computer". Click "Have Disk…" and select the folder (for example, D:\Drive) where the driver setup file is located, and click "OK".
Click "Close"→ "Close" → "OK" → "OK" on the following screens displayed in sequence. Microsoft® Windows® XP Operating System Insert the CD into the CD-ROM drive. Click "Start" → "Control Panel" then click the "Appearance and Themes" icon. Click "Display" icon and choose the "Settings" tab then click "Advanced.
Click the "Properties" button on the "Monitor" tab and select "Driver" tab. Click "Update Driver." and select "Install from a list or." then click the "Next" button. Select "Don't search ,I will." then click "Next" and then click "Have disk". Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button.
If you can see following "Message" window, then click the "Continue Anyway" button. Then click the "OK" button. This monitor driver is under certifying MS logo, and this installation doesn't damage your system. The certified driver will be posted on Samsung Monitor homepage http://www.samsung.com/ Click the "Close" button then click the "OK" button continually. Monitor driver installation is completed.
How to install Click "Start," "Setting," and then "Control Panel." Double click the "Display" icon. Select the "Settings" tab and click the "Advanced Properties" button. Choose "Monitor." Case1 : If the "Properties" button is inactive, it means your monitor is properly configured. Please stop installation Case2 : If the "Properties" button is active, click the "Properties" button then follow next steps continually. Click "Driver" and then click "Update Driver." then click the "Next" button.
Natural Color Natural Color One of the recent problems in using a computer is that the color of the images printed out by a printer or other images scanned by a scanner or a digital camera are not the same as those shown on the monitor. the Natural Color S/W is the very solution for this problem. It is a color administration system developed by Samsung Electronics in association with Korea Electronics & Telecommunications Research Institute (ETRI).
8. The "Installation Status" window appears. 9. Click "Finish." 10. When the installation is complete, the MagicTune™ executable icon appears on your desktop. Double-click the icon to start the program. MagicTune™ execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems (MagicTune™) The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment.
Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.
Control Buttons [ ] Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. [ ] These buttons allow you to adjust items in the menu. [ ] Press this button to activate a highlighted menu item. [AUTO] When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center.
Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming Analog signal. The values of fine, coarse and position are adjusted automatically. (Available in Analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'AUTO' function while the AUTO PATTERN is on.
When pressing the MENU button after locking the OSD Menu Description This is the function that locks the OSD in order to keep the current states of settings or prevent others from adjusting the current settings. Locked : Hold down the menu button for more than five seconds to activate the OSD adjustment lock function. OSD Locked & Unlock Unlock : Hold down the menu button for more than five seconds to deactivate the OSD adjustment lock function.
Menu MagicBright™ Description Push the MagicBright™ button to circle through available preconfigured modes. - Six different modes (Custom/Text/Internet/Game/Sport/Movie/) Volume Menu Volume SOURCE Description When OSD is not on the screen, push the button to adjust volume.
Menu Description SOURCE Selects the Video signal while the OSD is off.
Menu Brightness Description You can use the on-screen menus to change the brightness according to personal preference. MENU → Contrast Play/Stop → → , → MENU You can use the on-screen menus to change the contrast according to personal preference.
MagicColor is a new technology that Samsung has exclusively developed to improve digital image and to display natural color more clearly without disturbing image quality. MagicColor Off Demo Returns to the original mode. The screen before applying MagicColor appears on the right and the screen after applying MagicColor appears on the left. Full Displays not only vivid natural color but also more realistic natural skin color with clearness. Intelligent Displays vivid natural color with clearness.
MENU → Fine → , → MENU , → → , → → , → MENU , → → , → → , → MENU Changes the horizontal position of the monitor's entire display. (Available in analog mode only) MENU → V-Position → Changes the clearance of image. MENU → H-Position → Removes noise such as horizontal stripes. If the noise persists even after fine tuning, repeat it after adjusting the frequency (clock speed).
V-Position You can change the vertical position where the OSD menu appears on your monitor. MENU → Transparency → → , → , → → MENU Change the transparency of the background of the OSD. MENU → Display Time , , → → , → → , → MENU The menu will be automatically turned off if no adjustments are made for a certain time period. You can set the amount of time the menu will wait before it is turned off.
Menu Information Description Shows a video source, display mode on the OSD screen.
Check List Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? Check the signal cable connection.
the monitor and restore the image on the screen. I cannot see the On Screen Display. Have you locked the On Screen Display (OSD) Menu to prevent changes? Unlock the OSD by pressing the [ least 5 seconds. The screen shows strange colors or just black and white. Is the screen displaying only one color as if looking at the screen through a cellophane paper? Check the signal cable connection.
with Window OS that supports Plug and Play. Control Panel → Performance and Maintenance → System → Hardware → Device Manager → Monitors → After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware. MagicTune™ is an additional software for the monitor. Some graphic cards may not support your monitor. When you have a problem with the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.
Internet in the Client screen. that indicates that the LAN connection is disconnected. In this case, connect using another LAN cable. 2) Check if the settings of the 'Network' tab of 'Settings' have been properly set up. The default setting is "DHCP". If your network uses a static IP address, select 'Use the following IP address' and then enter the appropriate IP address information. The contents (video, voice) on the server do not play smoothly on the Client Monitor.
How can I set the Power Saving function? Windows XP : Set the resolution at the Control Panel → Appearance and Themes → Display → Screen Saver. Set the function at BIOS-SETUP of the computer. Windows ME/2000 : Set the resolution at the Control Panel → Display → Screen Saver. Set the function at BIOS-SETUP of the computer.
Environment The location and the position of the monitor may influence the quality and other features of the monitor. If there are any sub woofer speakers near the monitor, unplug and relocate the woofer to another room. Remove all electronic devices such as radios, fans, clocks and telephones that are within 3 feet (one meter) of the monitor. Useful Tips A monitor recreates visual signals received from the computer.
Specifications General Model Name SyncMaster 220TN LCD Panel Size 22 inch (55 cm) Display area 473.76 (H) x 296.1 (V) Pixel Pitch 0.282 (H) x 0.282 (V) Synchronization Horizontal 30 kHz ~ 81 kHz Vertical 56 Hz ~ 75 Hz Display Color 16.7 M Resolution Optimum resolution 1680 x 1050 @ 60 Hz Maximum resolution 1680 x 1050 @ 60 Hz Input Signal, Terminated RGB Analog 0.7 Vp-p ± 5 % separate H/V sync, Composite H/V sync TTL level (V high ≥ 2.0 V, V low ≤ 0.
Signal Cable 15pin-to-15pin D-sub cable, Detachable Dimensions (W x H x D) / Weight 520.0 X 399.0 X 68.5 mm / 20.5 X 15.7 X 2.7 inch (Without Stand) 520.0 X 452.0 X 202.0 mm / 20.5 X 17.8 X 8.0 inch / 7.9 kg / 17.4 Ibs(With stand) VESA Mounting Interface 100 x 100 mm (For use with Specialty(Arm) Mounting hardware.
4 watts 4 watts PowerSaver (When used as a Network monitor) This monitor has a built-in power management system called PowerSaver. This system saves energy by switching your monitor into a low-power mode when it has not been used for a certain amount of time. The monitor automatically returns to normal operation when you press a key on the keyboard. For energy conservation, turn your monitor OFF when it is not needed, or when leaving it unattended for long periods.
VESA. 1024 x 768 60.023 75.029 78.750 +/+ VESA, 1280 x 768 60.289 74.893 102.250 -/+ VESA. 1280 x 960 60.000 60.000 108.000 +/+ VESA. 1280 x 1024 63.981 60.020 108.000 +/+ VESA. 1280 x 1024 79.976 75.025 135.000 +/+ VESA.1680 x 1050 64.674 59.883 119.000 +/- Horizontal Frequency The time to scan one line connecting the right edge to the left edge of the screen horizontally is called Horizontal Cycle and the inverse number of the Horizontal Cycle is called Horizontal Frequency.
Contact SAMSUNG WORLDWIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America U.S.A 1-800-SAMSUNG (726-7864) http://www.samsung.com/us CANADA 1-800-SAMSUNG (726-7864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (726-7864) http://www.samsung.com/mx ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 4004-0000 http://www.samsung.com/br CHILE 800-SAMSUNG(726-7864) http://www.samsung.
AUSTRIA 0800-SAMSUNG(726-7864) www.samsung.com/at BELGIUM 0032 (0)2 201 24 18 http://www.samsung.com/be CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 70 70 19 70 http://www.samsung.com/dk FINLAND 030-6227 515 http://www.samsung.com/fi FRANCE 3260 SAMSUNG(726-7864) 08 25 08 65 65 (€ 0,15/Min) http://www.samsung.com/fr GERMANY 01805-SAMSUNG(726-7864) (€ 0,14/Min) http://www.samsung.de HUNGARY 06-80-SAMSUNG(726-7864) http://www.samsung.
CHINA 800-810-5858, 010- 6475 1880 http://www.samsung.com.cn HONG KONG 3698-4698 http://www.samsung.com/hk INDIA 3030 8282 1800 110011 http://www.samsung.com/in INDONESIA 0800-112-8888 http://www.samsung.com/id JAPAN 0120-327-527 http://www.samsung.com/jp MALAYSIA 1800-88-9999 http://www.samsung.com/my NEW ZEALAND 0800SAMSUNG(726-7864) http://www.samsung.com/nz PHILIPPINES 1800-10-SAMSUNG(726-7864) http://www.samsung.com/ph SINGAPORE 1800-SAMSUNG(726-7864) http://www.samsung.
Plug & Play This is a function that provides the best quality screen for the user by allowing the computer and the monitor to exchange information automatically. This monitor follows the international standard VESA DDC for the Plug & Play function. Resolution The number of horizontal and vertical dots used to compose the screen image is called 'resolution'. This number shows the accuracy of the display.
