SCC-C6323 SCC-C6325 SCC-C7325 10x Mini Smart Dome Camera user manual ENG FRE GER SPA ITA imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.
Safety information C CAUTION 1 RISK OF ELECTRIC SHOCK. DO NOT OPEN 2 CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE REAR COVER. NO USER SERVICEABLE PARTS INSIDE. REFER TO QUALIFIED SERVICE PERSONNEL.. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. 3 4 5 This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Safety information CAUTION 1. Do not drop objects on the product or apply strong shock to it. Keep away from a location subject to excessive vibrationor magnetic interference. 2. Do not install in a location subject to high temperature (over 50°C), low temperature (below -10°C), or high humidity. Doing so may cause fire or electric shock. 3. If you want to relocate the already installed product, be sure to turn off the power and then move or reinstall it. 4.
Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
Contents Introduction Features 7 Product & Accessories 8 Parts Name & Functions 10 Installation DIP Switch Setup 13 Installation using Surface mount on the Ceiling 14 Installation using Ceiling Mount Bracket (SCC-C7325) 16 Installation using Wall Mount Bracket (SCC-C7325) 17 Cabling 19 Operation 21 Preset and Pattern Function Pre-Check 21 Starting OSD Menu 21 Reserved Preset 21 Preset 22 Auto Pan 22 Pattern 22 Scan 23 Schedule 23 Other Functions 23 OSD Display of Main Scre
Contents How to use OSD Menu F Privacy Zone Mask Setup 26 Motion Setup 26 Function Setup 27 PRESET Setup 28 Auto Pan Setup 29 Pattern Setup 30 Scan Setup 30 Schedule Setup 32 Camera Setup 33 System Setup 34 System Initialize 36 ❖ ❖ Specifications Specifications 38 Dimension 41 ❖ 6 – 10X MINI SMART DOME CAMERA
Introduction FEATURES ❖ Camera Specifications • CCD Sensor : 1/4” Interline Transfer CCD • 7 rules of Schedule can be assigned by day and time. Appropriate actions (such as Home, Preset, Auto Pan, Pattern, Scan) can be defined for each rule. Also, it is possible to make rule by Weekday and Allday to simplify the rule.
Introduction PRODUCT & ACCESSORIES ❖ ❖ Product & Accessories (SCC-C6323) • Main Product Main Body Surface Mount Bracket • Accessory G Manual Screw & Plastic Anchor (4Pcs) ❖ Product & Accessories (SCC-C6325) • Main Product Main Body Surface Mount Bracket • Accessory Screw & Plastic Anchor (4Pcs) Terminal Block Torx Screw Driver Ú Mount Bracket Option : Please use SADT-937WM for this purpose.
Introduction ❖ Product & Accessories (SCC-C7325) • Main Product Main Body Sun Shield Housing • Accessory ENG Terminal Block Torx Screw Driver Manual • Mount Bracket Option Wall Mount Bracket (SADT-732WM) Ceiling Mount Bracket (SADT-732CM) English – 9
Introduction PARTS NAME & FUNCTIONS ❖ ❖ SCC-C6323 Surface Mount Bracket DIP Switch Cable Duct Separating Slit Dome Cover Main Unit / Surface Mount Bracket • Surface Mount Bracket This is used to install the camera directly on the ceiling. After separating this cover first and then attach this directly to ceiling. Camera must be assembled at the last stage. Do not use this bracket when installing camera on the wall with wall mount bracket or on the ceiling with ceiling mount bracket.
Introduction ❖ SCC-C6325 Surface Mount Bracket Mounting Hole Cabling Terminal Block Main Body Lockup Screw DIP Switch Dome Cover Main Unit / Surface Mount Bracket Back of Main Unit ENG • Dome Cover Do not remove the protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust. • Surface Mount Bracket This is used to install the camera directly on the ceiling. After separating this cover, mount this bracket on to ceiling.
Introduction PARTS NAME & FUNCTIONS D ❖ SCC-C7325 B s c Sun Shield Housing Cabling Terminal Block Main Body Lockup Screw DIP Switch Dome Cover Main Unit / Surface Mount Bracket • Dome Cover Do not remove the protection vinyl from dome cover before finishing all installation process to protect dome cover from scratches or dust. • Sun Shield Housing • Lockup Screw Fixes main unit brackets like surface, wall, and ceiling.
Installation • Select the appropriate Protocol with DIP switch combination. DIP SWITCH SETUP Before you install the camera, you should set the DIP switches to configure the camera ID, Baud rate, and communication protocol.
Installation ❖ RS-485 Termination Resistor ③ Placing lower body to Surface Mount bracket. The cable must be properly handled into hole of bracket or side of lower body. ON ON 1 2 3 4 5 6 7 8 • Pin 8 is used for ON/OFF of RS-485 Termination. Normally, it must be OFF state. Especially when you have trouble with long Daisy chain style connection, turn ON this termination switch of last camera.
Installation ⑤ Tighten locking screw. ❖ SCC-C6325 ① To pass cables to upside of ceiling, please, make about ũ60mm hole on the ceiling panel. ② Screw surface mount bracket to ceiling with 4 screws. ENG ⑥ Connect Video, communication, power cable properly. (see next section) ③ Wire cables to terminal block and connect the terminal blocks to main unit.
Installation ④ Screw main unit to surface mount bracket with 4 lock-up screws. INSTALLATION USING CEILING MOUNT BRACKET (SCC-C7325) ① Install ceiling mount bracket on the ceiling using 4 screws provided. ⑤ Detach protection vinyl from dome cover. 16 – 10X MINI SMART DOME CAMERA ② Turn sunshield clockwise after locating it in the pipe head of ceiling mount properly.
Installation ③ After wiring cables to terminals, plug the terminals into the bottom of main unit. Then, fix the main unit with sunshield with 4 screws. INSTALLATION USING WALL MOUNT BRACKET (SCC-C7325) ① Use the 4 screws (provided) to secure the wall mount bracket to the wall. ④ Detach protection vinyl from dome cover. English – 17 ENG ② Turn sunshield clockwise after locating it in the pipe head of wall mount properly.
Installation ③ After wiring cables to terminals, plug the terminals into the bottom of main unit. Then, fix the main unit with sunshield with 4 screws. C ❖ ❖ ④ Detach protection vinyl from dome cover.
Installation CABLING ❖ SCC-C6323 Dual Voltage DC 12V/AC 24V BNC Video Controller/DVR 1 (Black) : IN COM 2 (Yellow) : IN 1 3 (Brown) : IN 2 Sensors ENG 4 (Red) : Relay Out 5 (Orange) : Relay Out IrDA Sensor Door Switch Lamp Relay Out ❖ SCC-C6325/ SCC-C7325 Dual Voltage DC 12V/AC 24V IrDA Sensor Door Switch Relay Out Relay Out Controller/DVR Sensors BNC Video Lamp Relay Out Cabling Terminal Block English – 19
Installation ❖ Power Connection C • Please, check the voltage and current capacity of rated power carefully. Rated power is indicated in the back of main unit. Power Mode Input Voltage Range DC 12V AC24V Power Consumption C6323/ C6325 C7325 DC 11V ~ 15V 8W 12W AC 20V ~ 29V 10W 21W ❖ RS-485 Communication • For PTZ control, connect this line to keyboard and DVR. To control multiple cameras at the same time, RS-485 communication lines of them is connected in parallel as shown below.
Operation CHECK POINTS BEFORE OPERATION • Before power is applied, please check the cables carefully. • The camera ID of the controller must be identical to that of the camera to be controlled. The camera ID can be checked in the System Information of OSD Menu. • If your controller supports multi-protocols, the protocol must be changed to match to that of the camera. various functions using keyboard controller as well as simplify the interface with DVR and IP equipments.
Operation • Run Auto Pan PRESET Method1) [Auto Pan NO.] [Enter] • Function Method2) [Auto Pan NO.+140] ex) Run Auto Pan 2 : [142]] Max. 127 positions can be stored as Preset position. The Preset number can be assigned from 1 to 128. It is noted that preset “95” is reserved for starting OSD menu. • Delete Auto Pan Camera characteristics (i.e. White Balance, Auto Exposure) can be set up independently for each preset and they are adjusted by using OSD menu.
y Operation • Run Pattern Tuesday at 9:00AM. If you choose Weekday, camera will move to Main gate everyday except weekend. Method 1) [Pattern NO.] ex) Run Pattern 2 : [2] Method 2) [Pattern NO.+130] It is noted that due to the real time clock, the time data will be kept regardless of blackout. The initial time and day setup is essential to proper Schedule function.
Operation • Privacy Zone Mask • P/T/Z INFORMATION To protect privacy, MAX. 4 Privacy Masks can be created on the arbitrary position to hide objects such as windows, shops or private house. With Spherical Coordinates system, powerful Privacy Zone Mask function is possible. Current Pan/Tilt angle in degree, zoom magnification and a compass direction. • Camera ID Current Camera ID(Address).
How to use OSD Menu GENERAL RULES OF KEY OPERATION FOR MENU • The menu item surrounded with < > always means it has its sub menu. • For all menu level, to go into sub menu, press NEAR or ENTER key. • To go to up-one-level menu, press FAR key. • To move from items to item in the menu, use joystick in the Up/Down or Left/Right. • To change a value of an item, use Up/Down of the joystick in the controller. SYSTEM INFORMATION SYSTEM INFORMATION FIRMWARE VER COLOR SYSTEM PROTOCOL BAUD RATE ADDRESS 1.
How to use OSD Menu PRIVACY ZONE MASK SETUP ❖ Privacy Zone Size Adjustment EDIT MASK 1 PRIVACY ZONE MASK NO. DISPLAY CLEAR MASK 1 UNDEFINED OFF CANCEL [ :ADJUST MASK WIDTH] [ :ADJUST MASK HEIGHT] [NEAR:SELECT/ FAR:CANCEL] BACK EXIT Select area in image to mask. • MASK NO. [1~4] Select Mask number. If the selected mask has already data, camera moves as it was set. Otherwise, “UNDEFINED” will be displayed under “Mask NO”.
How to use OSD Menu • AUTO FLIP ❖ Alarm Input Setup [ON/OFF] Refer to “Other Functions” section. • JOG MAX SPEED [2°/sec ~360°/sec] Sets maximum jog speed. Jog speed is inversely proportional to zoom magnification. As zoom magnification goes up, pan/tilt speed goes down. • JOG DIRECTION ALARM1 N.O ALARM2 N.C PRESET1 NOT USED [INVERSE/NORMAL] If you set this to ‘Normal’, the view in the screen is moving same direction with jog tilting.
How to use OSD Menu • AUTO PAN SETUP • CAM ADJUST Up to 8 Auto Pans are available, which makes camera to move slowly between two preset points. • PATTERN SETUP Up to 4 patterns can be stored in the dome. In this function, path data created by manual move of Joystick are recorded and you can playback the identical path automatically whenever required. • SCAN SETUP Up to 8 Scans can be defined. In a Scan, max 20 entities are assigned from any combinations of Preset/Auto Pan/Pattern.
❖ Edit Preset Label AUTO PAN SETUP LABEL - PRESET 1 [█ ] ---------1234567890 ABCDEFGHIJ KLMNOPQRST UVWXYZabcd efghijklmn opqrstuvwx yz<>-/:. ---------- AUTO PAN SETUP OK CANCEL APAN NO. 1ST POS. 2ND POS. 1 NOT USED NOT USED APAN SPEED CLEAR APAN 30/SEC CANCEL BACK EXIT ① Edits label to show on monitor when camera arrives at presets. In Edit Label menu, a reverse rectangular is cursor. As soon as finishing selecting alphabet, cursor moves to the next digit.
How to use OSD Menu PATTERN SETUP EDIT PATTERN 1 PATTERN SETUP PATTERN NO. 1 UNDEFINED CLR PATTERN CANCEL [NEAR:SAVE / FAR:DELETE] 0/0/X1/N BACK EXIT • PATTERN Number [1~4 ] Selects Pattern number to edit. If a selected pattern number is not defined, “UNDEFINED” will be displayed under selected pattern number. • CLEAR PATTERN [CANCEL/OK] Deletes data in current pattern • EDIT PATTERN Starts editing pattern. ③ To save data and exit, press NEAR or ENTER key.
How to use OSD Menu ② Note that MAX. 20 Functions are allowed in a Scan. Move cursor up/down and press NEAR or ENTER key to set up. ④ Set up items such as Action, NO., Dwell and OPT. EDIT SCAN EDIT SCAN 1 NO. ACTION NO. DWELL OPT 1 2 3 4 5 NONE NONE NONE NONE NONE SAVE CANCEL [NEAR:EDIT ACT] [FAR :EDIT END] ③ Set up Action, Dwell time and Option. Note that selected item is displayed in reverse. Move cursor Left/Right to select items and move cursor Up/Down to change each value. 1 NO. ACTION NO.
How to use OSD Menu The meaning of each value: SCHEDULE SETUP DAY C Days: MON > TUE > WED> THU > FRI > SAT > SUN SCHEDULE SETUP WKD: Weekday MASTER ENABLE DAY TIME ACT 1 UNDEFINED 2 UNDEFINED 3 UNDEFINED 4 UNDEFINED 5 UNDEFINED 6 UNDEFINED 7 UNDEFINED BACK • MASTER ENABLE NO ON ON [CANCEL/OK] Start editing Schedule. ❖ Edit Schedule ① After move the Cursor to the number by using Up/Down keys, press “Near”(Enter) Key to edit.
How to use OSD Menu CAMERA SETUP • RED ADJUST [10~60] • BLUE ADJUST [10~60] ZOOM CAMERA SETUP FOCUS MODE SEMIAUTO DIGITAL ZOOM ON IMAGE FLIP OFF ❖ Auto Exposure Setup AE SETUP BACKLIGHT DAY/NIGHT BRIGHTNESS IRIS SHUTTER AGC DNR SENS-UP BACK EXIT BACK EXIT Setup the general functions of zoom camera module. • FOCUS MODE [AUTO/MANUAL/SEMIAUTO] Sets camera focus mode.
How to use OSD Menu • SENS-UP [AUTO(2~128)/OFF] Activates Slow Shutter function when luminance of image (signal) is too dark. It is possible to set up the maximum number of frames piled up one on another by Slow Shutter function. in the field are changed using Up/Down keys. To save the updated data, press the NEAR or ENTER key again It is noted that the range of date setup is limited from 01/JAN/2000 to 31/DEC/2037.
How to use OSD Menu FAN/HEATER SETUP FAN RUN TEMP HEATER RUN TEMP 40°C 5°C BACK EXIT • FAN RUN TEMP Above this temperature, the blower fan will start automatically. Range: 30°C ~ 80°C (86°F ~ 176°F) If you change the location of Home position, all horizontal locations of functions such as preset, pattern, scan, auto pan, and privacy zone mask will be shifted based on changed Home position.
How to use OSD Menu ❖ Initial Configuration Table • LANGUAGE You can select a preferred Language of OSD display from 7 choices. [ENGLISH/ ESPAÑOL/ FRANÇAIS/ DEUTSCH/ ITALIANO/ РУССКИЙ/ PORTUGUÊS] After selecting a language, press ENTER(NEAR) key.
How to use OSD Menu • Camera Configuration Focus Mode SEMIAUTO Digital Zoom ON Image Flip OFF White Balance AUTO Back Light OFF Day/Night AUTO1 Brightness 25 IRIS AUTO Shutter ESC AGC NORMAL DNR MIDDLE SENS-UP OFF Preset 1~128 Undefined Auto Pan 1~8 Undefined Pattern 1~4 Undefined Scan 1~8 Undefined Schedule 1~7 Undefined ENG • Function Data English – 37
Specifications SPECIFICATIONS Model NTSC CCD PAL • Main Unit 1/4’’ Interline Transfer CCD Max. Pixels 811(H)×508(V) 410K 795(H)×596(V) 470K Effective Pixels 768(H)×494(V) 380K 752(H)×582(V) 440K Horizontal Res. 520 TV Line(Color), 570 TV Line(B/W) S/N Ratio 50 dB (AGC Off) Zoom ×10 Optical Zoom, ×10 Digital Zoom Focal length Camera ❖ Appearance SCC-C6323N/P Video Signal System Min. illumination F1.8, f=3.
Specifications Model NTSC CCD PAL 811(H)´508(V) 410K 795(H)´596(V) 470K Effective Pixels 768(H)´494(V) 380K 752(H)´582(V) 440K 50 dB (AGC Off) Zoom x10 Optical Zoom, x10 Digital Zoom Focal length F1.8, f=3.8~38mm illumination 50 IRE 30 IRE 15 IRE 50 IRE 30 IRE 15 IRE Sens-up No No No 128 times 128 times 128 times Color 0.60 Lux 0.36 Lux 0.18 Lux 0.0047 Lux 0.0028 Lux 0.0014 Lux Day & Night Auto / Day / Night(ICR) Focus Auto / Manual / SemiAuto B/W (S/W) 0.06 Lux 0.036 Lux 0.018 Lux 0.
Specifications Model Video Signal System NTSC CCD PAL 1/4’’ Interline Transfer CCD Max. Pixels 811(H)´508(V) 410K 795(H)´596(V) 470K Effective Pixels 768(H)´494(V) 380K 752(H)´582(V) 440K Horizontal Res. S/N Ratio 50 dB (AGC Off) Zoom x10 Optical Zoom, x10 Digital Zoom Min. illumination F1.8, f=3.8~38mm illumination 50 IRE 30 IRE 15 IRE 50 IRE 30 IRE 15 IRE Sens-up No No No 128 times 128 times 128 times Color 0.60 Lux 0.36 Lux 0.18 Lux 0.0047 Lux 0.0028 Lux 0.
Specifications DIMENSION Unit (mm) ❖ SCC-C6323 ❖ SCC-C6325 ENG PIPE THREAD English – 41
Specifications Unit (mm) ❖ SCC-C7325 • Wall Mount Bracket 42 – 10X MINI SMART DOME CAMERA • Ceiling Mount Bracket
) Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking on the product, accessories or literature indicates that the product and its electronic accessories (e.g. charger, headset, USB cable) should not be disposed of with other household waste at the end of their working life.
