User Guide

ManualsBrandsSamsung ManualsLaptopNC10

3-1

- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 -

- This Document can not be used without Samsung's authorization -

NC10

3. Disassembly and Reassembly

3-1. NC10 Disassembly and assembly

Part Picture Description

Main

System

1. Before disassembling the system, the AC adapter and the

battery have to be separated.

2. As shown in picture 1, adhere KNOB to the end closely

into the arrow direction, then push the battery up as shown

in picture 2.

3. When the battery is pushed upwards, it can be separated.

4. Remove the BOTTOM screw.

IF only keboard is disassembled, remove only 3 BOTTOM

screws(ㅁ mark).

M2 x L8, Silver (15EA)

5. Remove the DOOR-MEMORY.

[Caution] Attention to red sentence.

Winchester_NC10_Eng.indb 1 2008-09-20 오후 1:36:02

Summary of content (12 pages)

PAGE 1
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly 3-1. NC10 Disassembly and assembly [Caution] Attention to red sentence. Part Picture Description 1. Before disassembling the system, the AC adapter and the battery have to be separated. 2. As shown in picture 1, adhere KNOB to the end closely into the arrow direction, then push the battery up as shown in picture 2. 2 1 1 3.
PAGE 2
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 6. Remove the memory by pushing the fixed-tap out. 7. Push the Hook up inwards by using a pin-set as shown in the picture, and then lift the key board up. [Notice] When you push the hook up, you have to be careful not to scratch Topdp. s shown in the picture, lift the top side of keyboard up and A then disassemble keyboard. Main System 8.
PAGE 3
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 9. As shown in the picture, separate the BOTTOMCOVER(LAN Connector side first) by widening the gap between the BOTTOM-COVER and the TOP. (Be careful not to make scratch in the gap using a wooden-driver.) s shown in the picture, separate the BOTTOM-COVER A by widening the gap between the BOTTOM-COVER and the TOP.
PAGE 4
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 12. Remove the Antenna Cable which is connected with wireless LAN, and then remove the Screw which fixes WLAN. [Aux(Black)] M2 x L4, Black (1EA) 1. White, Main 2. Black, Aux 13. Remove the Bluetooth Camera Cable and the LCD cable CONN. and disassemble the W/L Antenna Cable. 14.
PAGE 5
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 17. Separate the Top Ass'y from the LCD. 18. Remove the Screw which fixes the SIM Card Sub-board and the Main-Board, and then separate them. M2 X L4, Black (2EA) Main System 19. Remove the Screw (3 EA) which connects the RHE and the Main board and separate them. M2 X L4, Black (3EA) 20. Remove the RHE as shown in the picture.
PAGE 6
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 21. Remove the RHE as shown in the picture. M2 X L4 (4EA) [Notice] When you remove the Rubber-LCD-Cap, be careful not to scratch the Front.. 22. Insert your hand into the gap of the LCD Back and the LCD front and then separate first, the upper part of the LCD Front and second, the both sides of the LCD Front then finally the bottom part of it.
PAGE 7
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 25. Remove the Screw as shown in the picture. M2 X L4 (4EA) 26. Separate the Hinge and the LCD-Panel as shown in the picture. (When you separate the Hinge, remove the Hinge after lifting the LCD-Panel up.) LCD Ass'y 27. Dis-assemble the LCD-Cable and then remove the LCD Panel. 28.
PAGE 8
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 29. Remove the Tape inside the circle. 30. Pull the LCD cable up to the arrow direction and then separate it. 21-2. Method to disassemble LCD without disassembling Main System. As shown in the picture, Stand the Top Ass’y in a vertical direction. remove 4 Rubber-LCDCap and 4 screws LCD Ass'y M2 X L4 (4EA) 22-2.
PAGE 9
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 31. Remove the Bluetooth Module. 32. Remove the Speaker Cable and the Speaker. TOP Ass'y 33. Remove the MIC. 34. Remove the Molding. NC10 Winchester_NC10_Eng.
PAGE 10
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 35. Remove the Power S/W Ass’y. 36. Confirm the arrow mark for assembly direction on the Power S/W Sub board. TOP Ass'y 3-10 Winchester_NC10_Eng.indb 10 37. Check the Guide in which the Power S/W at bottom will be inserted, then you have to assemble the Power S/W.
PAGE 11
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 38. Remove the Touch-PAD FFC (BA41-00972A, BA4100973A). 39. Remove the Shield-Touch PAD (BA81-05892A). TOP Ass'y 40. Remove the Touch-Pad (BA58-02418A). 41. During assembly, check the arrow direction, and then assemble the Touch –Pad Module for the arrow of the Touch-Pad to meet the arrow of the TOP fixture. NC10 Winchester_NC10_Eng.
PAGE 12
- 이 문서는 삼성전자의 기술 자산으로 승인자만이 사용할 수 있습니다 - This Document can not be used without Samsung's authorization - 3. Disassembly and Reassembly Part Picture Description 42. Complete it. TOP Ass'y 3-12 Winchester_NC10_Eng.