NETWORK CAMERA User Manual PNM-9000QB/ SLA-T1080FA/SLA-T2480A/T2480VA/T4680A/T4680VA SCL-150
Network Camera User Manual Copyright ©2020 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 22. Installing or using the product in water can cause serious damage to the product. 23. This device has been verified using STP cable. The use of appropriate GND grounding and STP cable is recommended to effectively protect your product and property from transient voltage, thunderstroke, communication interruption. 4. Follow all instructions. 5. Do not use this apparatus near water. 6.
overview Class construction Please read the following recommended safety precautions carefully. An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. ~~ Do not place this apparatus on an uneven surface. ~~ Do not install on a surface where it is exposed to direct sunlight, near heating equipment or heavy cold area. ~~ Do not place this apparatus near conductive material. ~~ Do not attempt to service this apparatus yourself.
CONTENTS OVERVIEW 6 7 7 10 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included (PNM-9000QB) What’s Included (Lens module -Optional) At a Glance INSTALLATION & CONNECTION 12 16 17 Installation Inserting/Removing a Micro SD card Connecting with other Device NETWORK CONNECTION AND SETUP 20 Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable
overview RECOMMENDED PC SPECIFICATIONS NAS RECOMMENDED SPECS ~~ ~~ ~~ ~~ ~~ ~~ ~~ Recommended capacity : 200GB or higher is recommended. ~~ For this camera, you are recommended to use a NAS with the following manufacturer’s specs. Recommended products : QNAP NAS, Synology NAS CPU : Intel(R) Core(TM) i7 3.4 GHz or higher RAM : 8G or higher Supported OS : MS Windows 8.1, 10, Mac OS X 10.
WHAT’S INCLUDED (PNM-9000QB) WHAT’S INCLUDED (LENS MODULE -OPTIONAL) Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) This is a lens module separately sold that is mounted to PNM-9000QB. Item Name Quantity Description Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.
overview Model Name SLA-T2480A Appearance Item Name Quantity 1 Lens Module 1 Quick Guide (Optional) 1 Quick Guide (Optional) 1 Tapping Screw 2 Used for installation on the wall or ceiling Lens module bracket 1 Use this for lens module installation Cable tie 1 Use this for organizing the cable Cable to connect lens module 1 Use this when connecting the main unit and lens module RJ12 Plug 1 Use this when adjusting the length of the cable to connect the lens module Item Name Quantity
Model Name Item Name Quantity 1 Lens Module 1 Quick Guide (Optional) 1 Quick Guide (Optional) 1 Tapping Screw 2 Used for installation on the wall or ceiling Lens module bracket 1 Use this for lens module installation Cable tie 1 Use this for organizing the cable Cable to connect lens module 1 Use this when connecting the main unit and lens module RJ12 Plug 1 Use this when adjusting the length of the cable to connect the lens module Cable to connect lens module (15 m) 1 Use this whe
overview AT A GLANCE Side of the main unit Front of the main unit a a b c d e f g h b Item Item Description a Connection terminal of lens module This terminal is connected to the lens module through the cable to connect the lens module. b HDMI port By connecting an HDMI cable, you can watch a live feed on the monitor.
Appearance of lens module b b a !! OVERVIEW a a a b Item b b Description a Lens Module This lens module is used to shoot video. b Main unit connection terminal This terminal is connected to the main unit through the cable to connect the lens module.
installation & connection INSTALLATION 2. Use four screws provided to join the installation bracket to the main unit. Precautions before installation Ensure you read out the following instructions before installing the camera: ~~ Organize the cable separately in order to prevent excessive burden on the lens module while the camera is installed (within 1m from the lens module ). ~~ Select an installation site that can hold at least 5 times the camera’s weight.
Install lens module (SLA-T2480A/SLA-T4680A) 1. Drill a hole which the lens is passed through at the location where you want to install it. 1. Use two screws provided or remove protective film to use the doublesided tape on the bottom side of the lens module bracket to install the lens module bracket. size (inner diameter): Ø30 ± 2mm JJ `` Hole (If the size of the hole is outside of this range, the installation may fail.) JJ `` Remove foreign substances on the target object before attachment.
installation & connection Install lens module (SLA-T2480VA/SLA-T4680VA) Installing the lens module in the main unit 1. Make a hole for the lens module at the spot where you want to install it. Connect the lens module cable to the [CAMERA] port on the side of the main unit. JJ `` Connect the lens module and turn it on. `` Turn off the main unit power when connect or remove lens module `` Install the lens at least 3 meters away from the main unit.
Connect lens module cable to lens module Adjust the length of the cable for connecting the lens module 1. Unscrew the back cover by turning it counterclockwise. The length of the cable for connecting the main unit and lens module can be adjusted. Please follow the steps in the correct order to adjust the length of the cable for connection: sure to remove the back cover first and assemble/disassemble the RJ45 JJ `` Beconnector. 1. Cut out the cable from the RJ12 Plug at the length you want.
installation & connection INSERTING/REMOVING A MICRO SD CARD JJ `` Disconnect the power cable from the camera before inserting the Micro SD card. Removing a Micro SD card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. `` When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended. Inserting a Micro SD card Insert a Micro SD card in the arrow direction shown in the figure.
CONNECTING WITH OTHER DEVICE Network Cable Specification Contents RJ45 (10/100/1000BASE-T) Ethernet 10/100/1000Base-T Cable Category 6 Max Distance 100 m PoE+ Support IEEE 802.3at Remark To operate with 1000BASE-T, a cable of Category 6 or higher should be used for the Giga hub. DC Resistance ≤ 0.125 Ω/m HDMI Supported Monitor PoE+ or DC 12V power connection Power Supply Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.
installation & connection Connecting to Audio Input/Output Connecting to the I/O port box Connect the Alarm I/O cable to the corresponding port of the port box. Speaker Microphone PC Network Microphone ~~ ALARM-IN : Used to connect the alarm input sensor or external day/night sensor. ~~ ALARM-OUT : Used to connect the alarm output signal. ~~ GND : Used for earth-grounding.
To connect the alarm out If devices (e.g., flashing light and siren) that exceed the voltage and current specifications are connected by using the open collector method, it may cause malfunction. !! INSTALLATION & CONNECTION Refer to the alarm out connection diagram below when connecting devices that exceed the voltage and current specifications. Alarm Out Wiring Diagram External connection Warning lamp / Siren power Inside of the camera DC 5V or 3.
network connection and setup You can set up the network settings according to your network configurations. CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING CONNECTING THE CAMERA DIRECTLY TO A DHCP BASED DSL/CABLE MODEM Connecting to the camera from a local PC in the LAN INTERNET 1. Launch an Internet browser on the local PC. Camera DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. External Remote PC DDNS Server (Data Center, KOREA) Camera 1.
USING DEVICE MANAGER manager program can be downloaded from - menu at Hanwha Techwin website MM `` Device (http://www.hanwha-security.com). AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1. Click at the main page of device manager. 2. Check the camera from the list. ~~ Check MAC address at the sticker attached to the camera.
network connection and setup Configuring Dynamic IP Receive IP address from DHCP ~~ Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server AUTOMATICALLY CONFIGURING IP 1. Click the camera from the list that you want to automatically configure the IP. -- If connecting the camera directly to modem using the DHCP protocols 2. Click < + > at the main page of device manager. ~~ Equipment Setting menu appears.
PORT RANGE FORWARD (PORT MAPPING) SETUP Setting up Port Range Forward for several network cameras If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. ~~ You can set a rule of Port Forwarding on the Broadband Router device through its configuration web page. ~~ A user can change each port using the camera setting screen. 1.
network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 1. Launch the Internet browser. If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar. ex) IP address : 192.168.1.100:HTTP Port number(8080) ; http://192.168.1.100:8080 - the Login dialog should appear. 1. Run the client or operating system in support of the Bonjour protocol. 2. Click the camera name for search.
web viewer PASSWORD SETTING When you access the product for the first time, you must register the login password. JJ `` For a new password with 8 to 9 digits, you must use at least 3 of the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
appendix TROUBLESHOOTING SOLUTION PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. ~~ This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver. of is set to , but no notification e-mail reaches me even when an analysis event had occurred.
Any changes or modifications in construction of this device which are not expressly approved by the party responsible for compliance could void the user's authority to operate the equipment. This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.
