User Manual
English - 49
Listening through a Receiver
You can listen to sound through a receiver instead of the TV speaker.
1 Press the Anynet+ button.
Press the ▲ or ▼ button to select Receiver, then press the
ENTER/OK button.
2 Press the ◄ or ► button to select to On, then press the
ENTER/OK button.
Now you can listen to sound through the receiver.
3 Press the EXIT button to exit.
➢
When the receiver is set to On, you can listen to the TV sound
through the 2-channel receiver.
➢
If the receiver is exclusively for a home theater only (supporting
audio only), it may not appear in the device list.
➢
Only when you have connected the optical jack of the TV and
the receiver properly, does Receiver work.
➢
In case of a content with copyright problems, listening through the receiver may not properly operate.
➢
When listening through the receiver, there are restrictions for using the PIP and audio-related menu.
Check Points before Requesting Service
Symptom Solution
Anynet+ does not work. ■ Check if the device is an Anynet+ device. The Anynet+ system
supports Anynet+ devices only.
■ Connect only one receiver.
■ Check if the Anynet+ device power cord is properly connected.
■
Check the Anynet+ device’s Video/Audio/HDMI 1.3 cable connections.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Check whether the TV remote control is in TV mode.
■ Check whether it is Anynet+ exclusive remote control.
■ Anynet+ doesn’t work at a certain condition. (Searching channels)
■ When connecting or removing the HDMI 1.3 cable, please make
sure to search devices again or restart your TV.
■ Check if the Anynet+ Function of Anynet+ device is set on.
I want to start Anynet+. ■ Check if the Anynet+ device is properly connected to the TV and
check if the Anynet+ (HDMI-CEC) is set to On in the Anynet+ Setup
menu.
■ Press the TV button on the TV remote control to switch to TV. Then
press the Anynet+ button to show the Anynet+ menu and select a
menu you want.
I want to exit Anynet+. ■ Select View TV in Anynet+ menu.
■ Press the
SOURCE button on the TV remote control and select a
device other than Anynet+ devices.
■ Press any of CH, CH LIST, and PRE-CH to change to the
TV mode. (Note that the channel button operates only when a
tuner-embedded Anynet+ device is not connected.)
The message Connecting to
Anynet+ device… appears on
the screen.
■ You cannot use the remote control when you are configuring
Anynet+ or switching to a view mode.
■ Use the remote control when the Anynet+ setting or switching to
view mode is complete.
The Anynet+ device does not
play.
■ You cannot use the play function when Plug & Play is in progress.
The connected device is not
displayed.
■ Check whether or not the device supports Anynet+ functions.
■ Check whether or not the HDMI 1.3 cable is properly connected.
■ Check whether Anynet+ (HDMI-CEC) is set to On in the Anynet+
setup menu.
■ Search Anynet+ devices again.
■ You can connect an Anynet+ device using the HDMI 1.3 cable only.
Some HDMI cables may not support Anynet+ functions.
The TV programme cannot be
recorded.
■ Check whether the antenna jack on the recording device is properly
connected.
The TV sound is not output
through the receiver.
■ Connect the optical cable between TV and the receiver.
Enter
Move
View TV
Select Device
Record
Menu on Device
Device Operation
Receiver :On
Setup
TV P 1
Exit
BN68-01352A-01Eng.indd 49 2007-10-06 ¿ÀÈÄ 5:51:41