SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page i Real Time DVR SHR-2040/2041/2042 User’s Manual English
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page ii SHR-2040/2041/2042 USER’S MANUAL Safety Regulations Please be sure to keep the following in mind for the right use of the product to pre-vent proprietary risk or damage. ■ Do not use multiple plugs at once. ● ■ Do not put a vase, flowerpot, cup, cosmetics, medicine, or vessel with water around you. ● ■ This may cause fire. Do not disassemble, repair, or remodel the product. ● ■ This may cause abnormal operation due to high temperature.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page iii Before we start This User’s Manual describes the basic usage of SHR-2040/2041/2042. This Manual contains all the matters necessary for using SHR-2040/2041/2042 such as brief instruction, part name, function, connecting other equipment, and menu setup of SHR-2040/2041/2042. - SEC retains the copyright on this User’s Manual. - This User’s Manual cannot be copied without SEC’s prior written approval.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page iv Contents ii Safety Regulations iii Before we start Standards Approvals 1 1-1 1. Introduction 1-2 2. Features 1-3 3. Part Names and Functions 2 English Chapter 2 Installation 2-1 1. Installation Environment Setup 2-3 2. Checking Product & Accessory 2-4 3. HDD Addition 3 Chapter 3 Connecting with other device 3-1 1. Connecting the Video, Audio, and Monitor 3-3 2. Connecting the Network 3-5 3. Connecting the USB 3-6 4.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM 5 Page v Chapter 5 Menu Setup 5-1 Before Use 5-2 1. System 5-14 2. Camera 5-18 3. Monitoring 5-20 4. Recording Mode 5-22 5. Event Record Mode 5-27 6. Schedule 5-29 7. Backup 5-30 8. Network 5-34 9. Network Setup 6 Chapter 6 PTZ Camera Control 6-1 1. PTZ Camera Control Mode 6-3 2. Basic Operation of PAN, TILT, & ZOOM 6-4 3. Preset Setup 6-6 4. Camera Menu Setup 6-7 5. Preset View 6-8 6.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM 9 English Chapter 9 Smart Viewer 9-1 1. Introduction 9-2 2. Feature 9-3 3. PC Specification(Recommendation) 9-4 4. Smart Viewer Installation 9-7 5. Smart Viewer Program Execution 9-8 6. Smart Viewer Initial Screen 9-9 7. Monitoring Mode 9-23 8. Search Mode 9-30 9. Setup Mode 10 vi Page vi Appendix 10-1 1. Product Specification 10-4 2. Outline Drawings 10-6 3. Factory Default 10-9 4.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1 Chapter 1 Overview
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1-1 SHR-2040/2041/2042 USER’S MANUAL 1 Introduction The Digital Video Recorder(DVR) compresses the 4 channel of camera input data into the MPEG4 video file and the 4 channel of voice input data into the ADPCM audio file in the real time to record them in the Hard Disk or retrieve them from the Hard Disk simultaneously.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1-2 2 Features ■ 4 CH Composite Input Connectors ■ NTSC / PAL Video Source Compatible ( NTSC : SHR-2040 / SHR-2041 / SHR2042, SHR-2040N / SHR-2041N / SHR-2042N PAL ■ : SHR-2040P / SHR-2041P / SHR2042P ) Able to record the CIF sized (NTSC-352 x 240 / PAL-352 x 288) video at the speed of 120 ips(NTSC)/100ips(PAL)(Image Per Second) ■ 4 CH Loop Through Video Connectors ■ Hard Disk Overwrite Mode ■ Large Quantity Hard Disk Backup by USB2.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1-3 SHR-2040/2041/2042 USER’S MANUAL 3 Part Names and Functions [SHR-2040] No. Name 1 Power LED Alarm LED lights on when an event occurs. HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Network LED Displays both network connection and data transmission conditions. Backup LED Displays Back Up Mode. Rec LED 1 2 4 ... AUDIO 3 ALARM 4 Function Displays power on/off condition.
SHR-2040/2041/2042-ENG-1013 10/19/07 No. 10:23 AM Page 1-4 Name Function PTZ 7 ZOOM 8 TELE FREEZE 9 WIDE SEARCH 10 VIEW MENU 11 PRESET 12 PTZ Button Performs the TELE, WIDE, PRESET, and VIEW function. ZOOM(TELE) Button Sets up Digital Zoom(x2). ( Performs the TELE function by pressing the PTZ button.) FREEZE(WIDE) Button Performs the FREEZE function in the DISPLAY Mode. ( Performs the WIDE function by pressing the PTZ button.) SEARCH(VIEW) Button Displays the search method.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1-5 SHR-2040/2041/2042 USER’S MANUAL [SHR-2041] [SHR-2042] No. Name 1 Displays power on/off condition. Alarm LED lights on when an event occurs. HDD Access LED Displays Normal Access to HDD. Upon Access to HDD, LED repeats on and off. Network LED Displays both network connection and data transmission conditions. Backup LED Displays Back Up Mode. Rec LED Eject Button 2 1 3 4 ...
SHR-2040/2041/2042-ENG-1013 10/19/07 No. 10:23 AM Page 1-6 Name Function Displays 4 split screen. Displays the selected channel to the Single Mode MODE 7 Mode Selection Button Displays both LIVE Channel and Playback Channel in the PIP Screen simultaneously. Search Displays 6 split screen. (1 CH playback screen and 4 CH live screen) Displays 9 split screen.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1-7 SHR-2040/2041/2042 USER’S MANUAL [SHR-2040] Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. No. English Function Composite Video Signal Input Port (BNC Style Connector) 1 VIDEO IN 2 THROUGH You may use THROUGH port to transmit a video signal to the other video equipment.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 1-8 [SHR-2041/2042] Caution Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. No. Name Function 1 VIDEO IN 2 THROUGH You may use THROUGH port to transmit a video signal to the other video equipment.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3 Chapter 2 Installation
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-1 SHR-2040/2041/2042 USER’S MANUAL 1 Installation Environment Setup Do not play DVR on the carpet or other soft material to prevent clogging of the air ventilator. To play DVR on the cabinet or rack, be sure to check the ventilation condition. You should pay attention to the following before you use the product. 1. Do not use it outdoor. 2. Do not let water or liquid in the connection part or the product itself. 3.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-2 1. The rack on which the DVR is mounted should not be sealed off. 2. And it also can allow air circulation through the vent. 3. As in the figure to the right, we recommend the product should be stacked up with other DVRs or rack-mounting devices at a certain space or you install a vent system to accommodate airflow. 4.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-3 SHR-2040/2041/2042 USER’S MANUAL 2 Checking Product & Accessory Upon delivery of a product, you shall unwrap the product and put it on the even floor or where you want to use it. Then you shall check if the following items are in it. ■ ■ ■ ■ ■ ■ ■ Main Body User’s Manual One Power Cord Two Brackets - These are not supplied in SHR-2040. - Brackets are used to attach the product to the rack.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-4 3 HDD Addition Caution [Checking HDD Data] Please, pay attention to Following information to minimize the chance of losing HDD data. - Remember that you should protect HDD from any impact or misuse as this may cause damaged. - The Manufacturer is not responsible for missing data or defects caused by the user’s mishandling. Note: Adding Extra HDD. Check in advance that the HDD is compatible with the manufacturer’s DVR.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-5 SHR-2040/2041/2042 USER’S MANUAL [How to Add a HDD] 1. To remove the product’s cover, take out the screws on the left and right sides (2 spots each) and on the back (3 spots). 2. Remove the cover from the product. (Remove the cover by first lifting its back part upward after sliding the cover slightly backward.) 3.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-6 4. Remove the bracket-HDD from the product by lifting it upward from the product. 5. Mount the HDD to the bracket-HDD with the SCREW-TAPTITE (BW, +, S, M3, L6, ZPC) (4 spots) that was provided as an accessory. (The screws have to be tightened so that it doesn’t vibrate loose.) 6. Re-mount the built-in HDD bracket-HDD to the place where it was separated from. The work order for mounting the BRACKET-HDD is in reverse from when disassembling it.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-7 SHR-2040/2041/2042 USER’S MANUAL 7. Make sure that the bracket-HDD is mounted stably inside the product, then connect the power supply cable and signal transmission cable (IDE cable) to the HDD. 8. Check if there is any problem with connector or wiring inside of the product for connecting and mounting then close the cover. 9. Tighten cover mounting screws.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-8 SHR-2041 HDD ADDITION The user can add 3 HDDs to this product. However, there are many factors that can cause electrical shock, accidents, and malfunctioning of the device inside of the product. When the user does not correctly install or apply the proper settings, the device may not recognize the HDD or the device will not run. Therefore, before adding any HDDs, it is recommended that the user contacts a specialist where you purchased the product.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-9 SHR-2040/2041/2042 USER’S MANUAL 2. Remove the cover from the product. (Remove the cover by first lifting its back part upward after sliding the cover slightly backward.) 3. There is a bracket (bracket-HDD) mounted on the right and left sides where you can mount the HDD, and you have to remove the screws that are holding the bracket that you want to mount an HDD onto.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-10 4. Remove the bracket-HDD from the product by separating the power supply cable, signal transmission cable (IDE cable), and fan cable then pulling it toward the center of the product to separate its fixed part from the bottom. 5. Mount the HDD to the bracket-HDD with the SCREW-SPECIAL (BWH, 6-32UNC, L10.5) (4 spots) that was provided as an accessory. (The screws have to be tightened so that it doesn’t vibrate loose.
SHR-2040/2041/2042-ENG-1013 10/30/07 5:29 PM Page 2-11 SHR-2040/2041/2042 USER’S MANUAL 6. Re-mount the built-in HDD bracket-HDD to the place where it was separated from. Place the bracket-HDD so that all five mounting spots on the bottom and the bracket-HDD’s mounting holes are perfectly aligned, then slide it toward the outside of the product and tigh ten the screws. 7.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-12 SHR-2042 HDD ADDITION The user can add up to 2 HDDs to this product. However, there are many factors that can cause electrical shock, accidents, and malfunctioning of the device inside of the product. When the user does not correctly install or apply the proper settings, the device may not recognize the HDD or the device will not run.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-13 SHR-2040/2041/2042 USER’S MANUAL 2. Remove the cover from the product. (Remove the cover by first lifting its back part upward after sliding the cover slightly backward.) 3. There is a bracket (bracket-HDD) mounted on the right and left sides where you can mount the HDD, and you have to remove the screws that are holding the bracket that you want to mount an HDD onto.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-14 4. Remove the bracket-HDD (A) from the product by disconnecting the power supply cable, signal transmission cable (IDE cable), and fan cable then pulling it toward the center of the product to disconnect its fixed part from the bottom. Remove the bracket-HDD (B) by lifting it up after removing the screws. 5. Mount the HDD to the bracket-HDD with the (A)SCREW-SPECIAL (BWH,6-32UNC,L10.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-15 SHR-2040/2041/2042 USER’S MANUAL 6. Re-mount the built-in HDD bracket-HDD to the place where it was removed from. Place the bracket-HDD(A) so that all the five fixing areas in the bottom and the bracket-HDD’s fixing holes can perfectly aligned, then slide it outward of the product and tighten the screws.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-16 8. Check if there is any problem with connector or wiring inside of the product for connecting and mounting then close the cover. 9. Tighten cover mounting screws. (The left and right side each has 5 spots and back side has 1 spot) Caution When mounting an additional HDD, the primary master has to be mounted. The HDD has to be set as the primary master, and the CD-RW has to be set as the secondary master.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-17 SHR-2040/2041/2042 USER’S MANUAL WARNING ! Regarding the sub fan, you need additional brackets and sub fans as follows. The sub fan is shaped like this when viewed from the front and back. Please pay attention to the fan direction to let wind go through the fan.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-18 # Please install the fan which is seen at the right from the front view of SHR-set as follows. $ The cable should be out from the left hole.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 2-19
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3 Chapter 3 Connecting with other device
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3-1 SHR-2040/2041/2042 USER’S MANUAL 1 Connecting the Video, Audio, and Monitor [SHR-2040] 3-1 English
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3-2 [SHR-2041/2042] English 3-2
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3-3 SHR-2040/2041/2042 USER’S MANUAL 2 Connecting the Network ● Connecting to Internet through Ethernet(10/100BaseT) [SHR-2040] ● Connecting to Internet through ADSL [SHR-2040] 3-3 English
SHR-2040/2041/2042-ENG-1013 ● 10/19/07 10:23 AM Page 3-4 Connecting to Internet through Ethernet(10/100BaseT) [SHR-2041/2042] ● Connecting to Internet through ADSL [SHR-2041/2042] English 3-4
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3-5 SHR-2040/2041/2042 USER’S MANUAL 3 Connecting the USB 1. There are two USB connecting ports on the front and back of SHR-2040/2041/2042. 2. USB Hard Disk, USB CD/DVD, and USB Memory are connected through the front and back ports of SHR-2040/2041/2042. 3. Only one USB device can be connected with each USB connecting port. 4.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3-6 4 Connecting the Alarm Input/Output The Alarm IN/OUT port in the back of SHR-2040/2041/2042 is composed of the following elements. ● ALARM IN/OUT Connection Name Function - ALARM IN1 - ALARM IN2 - ALARM IN3 - ALARM IN4 ALARM Input Port 2 - ALARM RESET IN On receiving an ALARM RESET signal, the system cancels the current ALARM input and output signal and then resumes sensing.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM SHR-2040/2041/2042 USER’S MANUAL ● 3-7 English ALARM IN/OUT Connection Page 3-7
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 3-8 5 Connecting the RS-485 Device ● Connect the RS-485 Device through the back port of SHR- SHR-2040/2041/2042. ● You can install and control the PTZ camera supporting the RS-485 communication. ● You can adopt either Half Duplex or Full Duplex method for the connection.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5 Chapter 4 Live
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-1 SHR-2040/2041/2042 USER’S MANUAL 1 System Operation ● Turn the power on and the following LOGO pops up on the screen. ● After the LOGO appears, all of LED in the front flickers 6 times to initialize the system for operation. ● Upon completion of normal initialization, the Live screen appears accompanying a beep sound. ● It requires 30 to 40 seconds until the Live screen appears.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-2 2 Live Screen Mode Definition of Live Screen Icon The Live screen icons display the current setup and function status of each screen. CAM_01 V.Loss CAM_01 : Recording Icon Each icon represents Normal / Event (Alarm + Motion) / Schedule Recording. : Recording Video Size Icon Each icon represents the recording size of Large / Normal / CIF.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-3 SHR-2040/2041/2042 USER’S MANUAL : Auto sequence Icon This icon appears in the auto sequence mode. : Backup Playback Icon This icon appears when the backup data is played. : Fan Error Icon This icon appears when the fan stops. : No HDD icon This icon appears when there is a dysfunctional hard disk. V.Loss / V.Off : Video Input Status If there is no more video data input in the Video On, [V.Loss] appears in the channel.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-4 Selecting Live Screen Mode Each mode may be selected by [MODE Button] and [CH1 ~ CH4 Button]. The following figure shows Live Mode after converted. ● The default setup is 4 Split Screen Mode. ● You are able to choose other modes than Full Screen Mode by the [MODE] button in sequence. Whenever you press the [MODE] button, the system will change [4Split] ➝ [PIP] ➝ [auto sequence] ➝ [4 Split] in sequence.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-5 SHR-2040/2041/2042 USER’S MANUAL 3 Live Channel Selection and Audio On/Off Setup In other split modes than Full Screen Mode and Auto Sequence Mode, you can choose a channel to be displayed in each split area on your own. In addition, the channel being set to Audio On can be set to Audio On/Off in all Live Modes.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-6 4 Freeze and Zoom Freeze Function Freeze function pauses the video image in the Live Screen, it is only available in the Live Mode. You can set freeze to on or off with the [FREEZE] button. Zoom Function Zoom function enlarges the selected area to double size, and it is only available in the single mode. If the [ZOOM] button is pressed in the single mode, the Zoom area appears. Use the UP/DOWN/LEFT/RIGHT key to adjust the position of Zoom area.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-7 SHR-2040/2041/2042 USER’S MANUAL 5 Event Monitoring Event monitoring displays the channel synchronized with a event on the screen when a special event (Sensor/Motion/Video Loss) occurs. Event monitoring On/Off and event duration setup is available in [Menu] ➝ [Monitoring] mode.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-8 6 Spot-out Monitoring Spot-out Monitoring has nothing to do with Live Screen Output, it monitors the full screen of a certain channel. If you select the Monitoring in the MENU, the one channel among CH1 ~ CH4 is output with a Spot-out or channels are output one by one at an interval as Auto Sequence Mode in the Live Mode. Live screen icon does not appear in the spot-out monitoring. The interval is as same as the Auto Sequence time in the Live Mode.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 4-9
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5 Chapter 5 Menu Setup
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-1 SHR-2040/2041/2042 USER’S MANUAL Before Use 5-1 English ● User validation for entering the MENU window Press the “MENU” key to enter the Menu Setup window. Select Menu out of Menu, Backup, and Shutdown in the Setup field. (You can also perform the Backup and Shutdown functions after this user validation checkup.) The ID is fixed to Admin because only the user with Admin privilege can enter the Menu window.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-2 1 System ● System Menu has the following items in detail. Date/Time/Language Setup ● Date Press the “Enter” key and the ¦, key to move to Y/M/D. Use the , key to change the date. Press the “Enter” key to come out of the mode. ● Time Press the “Enter” key and the ¦, key to move to H/M/S. Use the , key to change the time. Press the “Enter” key to come out of the mode.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-3 SHR-2040/2041/2042 USER’S MANUAL Note [Date/Time Change] Pressing “OK” after you change date and time, you will be asked by a pop-up window if you really confirm the change. Here, press ”Yes” to change the time. Since Date/Time does not change in backup process, be sure to stop the backup process before you change Date/Time. If the date or time is changed, the system reboots.
SHR-2040/2041/2042-ENG-1013 ● 10/19/07 10:23 AM Page 5-4 DST (Daylight Saving Time) DST sets the clock one hour ahead the local standard time. This setting enables the system to display the time adjusted for DST. If the DST is set to Off, it does not apply. To set the DST, enter the start time and end time on the right. It allows you to set month, week (e.g. 1st, 2nd, 3rd, 4th, last), day, and time. Note [On DST Setup] Backup in progress will be cancelled.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-5 SHR-2040/2041/2042 USER’S MANUAL ● ● ● ● Password Lock If it is set to On, a pop-up window for user validation (You have to fill in the Setup, ID, and Password fields.) appears every time you select a menu. If it is set to Off, you can enter menus without entering the password. Record Lock If the Record Lock is set to On, a pop-up window, asking for the password appears while disabling the recording.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-6 System Log ● System Log is used to check the important record by an administrator. ● It displays such contents of a system related log and its execution date/time as System Start, System Termination, and Menu Setup Change. ● First : Moves to the first Log page. ● Prev : Moves to the previous Log page. ● Next : Moves to the next Log page. ● Last : Moves to the recent Log page.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-7 SHR-2040/2041/2042 USER’S MANUAL System Information and Setup This setup window provides the following setting items: ● Software Version: Displays the current software version. The value cannot be changed. ● Broadcast Format: Displays the current broadcast format (NTSC/PAL). The value cannot be changed. ● Mac Address: 6-Byte hardware address. The value cannot be changed. ● USB S/W Upgrade You can update the software using an USB device.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-8 Storage Setup You can configure the storage device related settings. ● Device Information Displays the number, capacity, and usage of ATA and USB devices. The displayed values are not changed. You can remove the data in HDD or USB memory after checking in the Erase box. ● Disk End Mode Stop: Stops recording when the disk is full while recording is still in progress.
SHR-2040/2041/2042-ENG-1013 11/2/07 9:14 AM Page 5-9 SHR-2040/2041/2042 USER’S MANUAL Note 1 [Internal HDD] This is a physical hard disk connected with the IDE cable inside the SHR-2160/2162/2080/2082 main body, and stores data. [External HDD] This is a physical hard disk connected with the port and terminal in the back of the SHR-2160/2162/2080/2082 main body, and stores data. This can be used as Extended HDD or Backup HDD. - Extended HDD : Supplements Internal HDD quantity.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-10 Note 2 [ATA] Usage : Internal HDD This is a physical hard disk connected with the IDE cable inside the SHR-2160/2162/2080/2082 main body. [USB] Usage : External HDD(Extended HDD or Backup HDD) It is physical hardware that is connected to the front/back part of the SHR-2160/2162/2080/2082 with the USB port. Caution [Device Erase] Data will not be deleted in the backup mode. Please be sure to stop the backup before you delete a data.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-11 SHR-2040/2041/2042 USER’S MANUAL Export/Import the Configuration This menu is used to export or import the DVR-related settings to/from the USB memory. The related settings are as the following: ● Mode: You can select any of Import and Export. 5-11 English ● File Name or File Open: The file naming is YYMMDD00 by default. “00” is the serial number so it increases by 1. If you want to change the file naming, press the ENTER button.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-12 Remote control Device ● MENU for the use of Samsung system keyboard Remote Control Device Device Samsung System Keyboard ID Baudrate Parity Date Stop Duplex 000 9600 None 8 1 Half Duplex OK ● Cancel Device A Remote Control Device, being connected to the RS485 port. ● ID This is a private ID of SHR-2040/2041/2042. This private ID is essential for SSC-2000 because SSC-2000 can control many SHR-2040/2041/2042 DVRs.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-13 SHR-2040/2041/2042 USER’S MANUAL System Shutdown ● Terminates the work in action safely and turns the power off. Press “OK” in the confirmation window and plug out when you see “Safe to Power Off”. Caution [System Shutdown] Power-off without terminating the system in the System Shutdown menu may incur improper motion like data loss and disk failure. Power-off shall be done in the System Shutdown menu.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-14 2 Camera ● The detailed Camera Menu items are as follows. Camera Config. g Cam 1 2 3 4 Video On On On On Audio Off Off Off Off Title CAM_01 CAM_02 CAM_03 CAM_04 Auto Seq 5sec 5sec 5sec 5sec OK Cancel ● Video On : Camera images from a selected channel appear. Off : Camera images from a selected channel disappear. Covert1 : Displays the information except for the Video information of selected channel.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-15 SHR-2040/2041/2042 USER’S MANUAL 5-15 English ● Title You can name the camera of selected channel. If you press the [Enter] key, the Virtual keyboard will come out. Virtual Keyboard If you move the cursor, you can type text by text. Up to 15 texts can be typed. Keyboard cannot be composed of all spaces. Pressing Caps Lock changes the keyboard that can be selected.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-16 PTZ Device ● ID It is an ID for PTZ Camera and available to set from 0 to 255. ● Protocol It is supported by the PTZ device. The following protocols are now being supported. Samsung / Vic. / Pan. / AD / Phi. / Ern. / Pel-D / Pel-P / Vcl. / Dia. / Kal. /Tech. ● Baurate Baurate is supported by the PTZ device. 600 / 1200 / 2400 / 4800 / 9600 / 19200 / 38400 ● Parity It is set to the one of None, Even, and Odd.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-17 SHR-2040/2041/2042 USER’S MANUAL Screen Setup 5-17 English ● It is a window to set Brightness/Contrast/Color for the camera image of each channel. Put the cursor on the channel that you want to adjust and set Brightness/Contrast/Color. Once selected, the channel appears in the right PIP area. Use the or button to adjust the value from 0 to 100. ● If you select CH >, all the channels will have the same values as the selected channel.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-18 3 Monitoring Monitoring Event Monitoring OSG Display Spot Out Channel Spot Out Event Monitor Monitor Out Duration Date Time Title Status CH1 Off Composite Out Off On On On On OK ● Cancel Event Monitoring It is possible to set to Off / 3sec / 5sec / 10sec / 20sec / 30sec / Continuous. ① Off : Event Monitoring does not operate to turn to the screen where an event occurs.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-19 SHR-2040/2041/2042 USER’S MANUAL ● Monitor You are not allowed to connect VGA OUT and Composite / S-Video OUT simultaneously. Consequently, the user is obliged to choose either Composite Output or S-Video Output. ① Composite : Makes the output come out through the “Composite / S-Video OUT” port. ➁ VGA : Makes the output come out through the “VGA Out” port.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-20 4 Recording Mode Record Mode ● Details for Record Mode Menu are as follows. NTSC PAL If you press the front “REC” button, the mode value to be recorded will be set. ☛ For the setup of Event Recording Mode value, refer to 5-20. Event Recording Mode Setup Menu. ● Mode On : The current channel is recorded if the REC button is pressed. Off : The current channel is not recorded even thought the REC button is pressed.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-21 SHR-2040/2041/2042 USER’S MANUAL Record Video size Mode ● Video size It sets the video to be recorded. Half D1 : (NTSC) 720x240(N) ➝ Normal (PAL) 720x288(N) ➝ Normal CIF : (NTSC) 352x240(C) ➝ CIF (PAL) 352x288(C) ➝ CIF ● Auto Deletion If you click the [off] button, you can select from on/off. Select “On” to move to the Date selection button and to limit the search date.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-22 5 Event Record Mode ● The detailed items of Event Record Menu are as follows. MENU Event Record Mode setup NTSC PAL ● Event Record Mode setup Sets a mode to be recorded when an event occurs. ● V. Size (Video Size ) Sets the size of a screen to be recorded.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-23 SHR-2040/2041/2042 USER’S MANUAL ● Quality Quality will be determined. Select the one among Very High / High / Standard / Low ● Rate Sets the Rate the number of screen recorded every second. It you set to 15.00 ips, the system records too many screens per second and play continues intermittently since recording is more detailed. This is appropriate for concentrated monitoring zone setup. In case of NTSC, select the one of 30.00 ips / 15.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-24 Alarm Detection Setup ● Off : Sensor does not operate. ① N.O(Normal Open) Sensor : Sensor remains open all the time and if closed, an alarm will be issued. (A Contact) ➁ N.C(Normal Close) Sensor : Sensor remains closed all the time and if open, an alarm will be issued. (B Contact) ● Cam It is used to set a camera that synchronizes with the current sensor. The default setting follows the sensor number.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-25 SHR-2040/2041/2042 USER’S MANUAL Motion Detection Setup ● Motion Detection Mode Off : Motion Detection does not operate On : Motion Detection operates. ● Area Selects the Motion Detection area. It is composed of 45x40(NTSC)/45x48(PAL) sized Block. It is impossible to set 4 block rows(Up/Down/Left/Right) to allow them to be displayed in all monitors. Select All : Selects the whole area. Select Block : Selects a block every time.
SHR-2040/2041/2042-ENG-1013 ● 10/19/07 10:23 AM Page 5-26 Sensitivity Sets the sensitivity of motion detection. Sensitivity: 1(L), 2, 3, 4, 5, 6, 7, 8, 9, 10(H). ● Alarm-Out Sets the Alarm-Out when Motion occurs. 5 Alarm Outs are supported. Select an alarm-out that you want to synchronize with the current motion channel. Multi-selection is possible. ● Duration Sets the Alarm-Out Duration. Alarm-Out continues for the determined duration.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-27 SHR-2040/2041/2042 USER’S MANUAL 6 Schedule This setup selects a time to record automatically. Selection by the day or by the time is available. The default value is set to “Event Record”. ● Press “CH >” copies the value of Channel 1 to all the channels. ● The horizontal axis numbered from 0 to 23 represents the time value. The vertical axis numbered from S to H represents the day value.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-28 Alarm Out Schedule You can schedule the automatic output for alarms. Alarm Out Schedule AO All S M T W T F S H Alarm 1 Off On Event Driven Alarm 2 Alarm 3 Holiday Alarm 4 OK Beep Cancel The scheduling is enabled by selecting alarms, days and time blocks. The default setting is Event Driven. For each alarm or beep, you can activate or deactivate alarming. In case of Event Driven, the alarm can be sent only when an event is issued.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-29 SHR-2040/2041/2042 USER’S MANUAL 7 Backup ● ● ● ● ● ● ● ● ● If there is a device, the free space and the backup device is displayed. Select a date, time, and camera No. to backup, and press “Start”. When you change Start Date/Time or End Date/Time, free space keeps updated in the Free Space zone. But the Select/Free values are displayed when you have marked the Check box. A file name is composed of Folder/File Name.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-30 8 Network IP Setup ● Connection Mode Designates the kind of the network connected to the main body of SHR-2040/2041/2042. Static IP : When the main body is connected to the network with Static IP. Dynamic IP : When the main body is connected to the network with Dynamic IP supplied by DHCP. ADSL(PPPoE) : When the main body is connected to the ADSL network with PPPoE.
SHR-2040/2041/2042-ENG-1013 10/30/07 5:28 PM Page 5-31 SHR-2040/2041/2042 USER’S MANUAL ● IP Sets the IP address for the main body of SHR-2040/2041/2042 to connect with the network. If the Connection Mode is set to Static IP, you shall type in IP yourself. If the connection mode is Dynamic IP or ADSL(PPPoE), the IP allocated by the DHCP server or ADSL company will be automatically displayed. In case of failure of DHCP or ADSL connection, 000.000.000.000 will be displayed.
SHR-2040/2041/2042-ENG-1013 ● ● ● ● ● ● ● 10/30/07 5:32 PM Page 5-32 You may select either TCP or UDP for the protocol type. If you select ADSL from the IP setup page, only TCP is available. While TCP is selected, Audio transmission is not available. The available Port(TCP) ranges from 554 to 2046 and the port number will be changed by 4. Once the first digit is determined, the following 3 digits will change accordingly.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-33 SHR-2040/2041/2042 USER’S MANUAL Callback Settings ● The Callback function is used to forward a callback message to the IP where SmartViewer is in action in case Alarm, Motion Detection, or Video Loss event occurs. Callback Settings On/Off IP Address Port(UDP) Retry Transfer Alarm In Transfer Motion Detection Transfer Video Loss Transfer System Log On 192.168.001.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 5-34 9 Network Setup Port Setup for SmartViewer Connection ● The Port value for DVR registration of SmartViewer (Setup ➝ Site Setup) shall be as same as that of the set (TCP). ● If you want to use the IP Router, you shall forward the activated Port depending on the current setting value. - If set to TCP, allocate 4 ports to the IP Router whose Port(TCP) was set.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 6
SHR-2040/2041/2042-ENG-1013 10/19/07 10:23 AM Page 7 Chapter 6 PTZ Camera Control
SHR-2040/2041/2042-ENG-1013 10/19/07 10:24 AM Page 6-1 SHR-2040/2041/2042 USER’S MANUAL 1 PTZ Camera Control Mode ● Select a proper PTZ camera Configuration value in MENU to enter PTZ Control Mode. PTZ Device Cam 1 2 3 4 ID 002 001 002 003 Protocol Samsung Vic Pan.
SHR-2040/2041/2042-ENG-1013 ● 10/19/07 10:24 AM Page 6-2 Other PTZ Camera Control Modes perform its control in a single screen. Press the channel selection button in the left front to select the PTZ setting channel and press the PTZ button. If you succeed in entering Single Screen PTZ Camera Control Mode, the PTZ symbol on the screen will turn yellow from white while the PTZ button will turn blue.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:24 AM Page 6-3 SHR-2040/2041/2042 USER’S MANUAL 2 Basic Operation of PAN, TILT, & ZOOM ● PAN Press the LEFT or RIGHT button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to control PTZ Camera horizontally. PTZ ● TELE WIDE VIEW PRESET TILT Press the UP or DOWN button in front SHR-2040/2041/2042 in PTZ Camera Control Mode to control PTZ Camera vertically.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 6-4 3 Preset Setup ● Records a certain position of PTZ Camera. ● Memorizes up to 20 PTZ Camera positions at the moment. Note For AD Protocol PTZ Camera, this memorizes only 7 Presets. Caution When using a remote control device (SCC2000), it is possible to control the camera with the remote control limited to the Samsung protocol.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 6-5 SHR-2040/2041/2042 USER’S MANUAL 6-5 English ● Move the cursor to right and press ENTER in PTZ Control Mode first. Then, press the “Enter” to run P/T/Z/ operation mode in the PIP screen and press the “Enter” again to cancel P/T/Z/ Motion Mode. ● Press Enter at the Position Name position to see Virtual Keyboard. Enter the type position name and press the “OK” to save the position and position name.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 6-6 4 Camera Menu Setup ● Camera Menu is a menu supplied by PTZ Camera itself. This Menu sets up several conditions of PTZ Camera. Note Pan. or Samsung Protocol Camera only is authorized for Camera Menu setup. ● Press the Preset button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to select Camera Menu.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 6-7 SHR-2040/2041/2042 USER’S MANUAL 5 Preset View ● Preset setup allows your movement to a certain saved position of PTZ Camera. ● Press the VIEW button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to select Preset. PTZ TELE WIDE VIEW PRESET (For example, Samsung Protocol) ● 6-7 English Control the cursor until it reaches a preset position number that you want to move and you can check it in the right PIP Screen.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 6-8 6 Other View ● Press the “VIEW” button in front of SHR-2040/2041/2042 in Single Screen PTZ Camera Control Mode to supply PTZ Camera. This is a very special function. Note Samsung, Pan., Pel-P, or Pel-D Protocol PTZ Camera supports this function. Samsung : Auto Pan / Scan / Pattern Pan.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 6-9
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 7 Chapter 7 Recording
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 7-1 SHR-2040/2041/2042 USER’S MANUAL 1 REC (Normal Recording) ● Pressing REC the button starts recording as set in the record mode. Then, REC LED lights on and a recording icon appears on the screen. During the recording in HDD, the front HDD LED blinks. ● During the normal recording, you can stop it by pressing the REC button. If the recording stops, REC LED lights out.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 7-2 2 Schedule Recording ● While “Record Schedule” or “Schedule/Event recording” is selected in the Record Schedule menu, Schedule Recording automatically starts. Otherwise, Schedule Recording remains inactivated. During the Schedule Recording, Recording Icon appears on the screen. During the recording in HDD, the front HDD LED blinks. ● If the Event Recording is selected, the recording starts at the every event.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 7-3 SHR-2040/2041/2042 USER’S MANUAL 3 Event Recording ● Alarm Detection Sensor operation mode in Alarm of Event Record menu shall be set to N.O (Normal Open) or N.C (Normal Close). ● Motion Detection Motion detection in the Event Recording menu shall be set to On. ● Video Loss Detection Video Loss in Event Record menu shall be set to On. ● Event Recording Mode Sets the recording type when an event occurs.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 7-4 Chapter 8 Search and Play
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-1 SHR-2040/2041/2042 USER’S MANUAL Before Use 8-1 English ● Pressing the “SEARCH” button shows Search Menu on the screen as seen above. ● Calendar Search searches a video file by the use of a calendar at the desired time. ● Event Search searches a video file recorded by the occurrence of event. ● Date/Time Search searches a video file by the entering of a day and time. ● “Go To First” searches a video file from the oldest one.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-2 1 Calendar Search Calendar Search (Can Select 4 Channels) Sun Mon Tue Wed Thu Fri OK Sat Cancel ● Be sure to select both the channel and the date to search. And press the [OK] button to search for the desired time. ● Use a calendar to search the video file of desired time. Four channels in maximum are in the range of search. ● Select the channel up to 4 by the use of ¦, and Enter button.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-3 SHR-2040/2041/2042 USER’S MANUAL 2 Event Search 8-3 English ● Searches Normal Recording, Schedule Recording, Alarm Recording, Motion Recording, and V.Loss(Video Loss) Recording by the time. ● You shall select a channel to search to see the event information of the channel. ● On the basis of event information for each channel, the system searches a video file for the event. Only one channel is allowed for video search.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-4 3 Date/Time Search ● Use the Date/Time information to search a video file at the time as you desire. Up to 4 channels can be searched at once. ● After you select a channel with the , , [Enter] button, the checkbox on the right of selected event number will be checked. ● Use the button until you reach the Search Time setup line. Press the [Enter] button to change the search time.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-5 SHR-2040/2041/2042 USER’S MANUAL 4 Go to First Search 8-5 English ● Searches the oldest one among recorded video files. Up to 4 channels can be searched at once. ● After you select a channel with the , , [Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the search and to cancel. And press the [Cancel] button to cancel the search.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-6 5 Go to Last Search ● Searches the latest one among recorded video files. Up to 4 channels can be searched at once. ● After you select a channel with the , ,[Enter] button, the checkbox on the right of the selected channel number will be checked. ● Press the [Start] button want to start the search and to cancel. And press the [Cancel] button to cancel the search.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-7 SHR-2040/2041/2042 USER’S MANUAL 6 Backup 8-7 English ● First, select the backup device. ● Mark the data of device. ● Select the file name to backup, and the detail information of a file is displayed in the below. ● The [Previous] button shows the previous page. ● The [Next] button shows the next page. ● The [Start] button plays the desired file. ● The [Exit] button exits the menu.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-8 7 Playback II ● Press the PLAY/PAUSE button( ● If you used the SEARCH button for playback just before, the system would remember the information of the played channel until you click the PLAY/PAUSE button( II ) again, then the system plays the previous channel. If you press the PLAY/PAUSE button( II ), the Search Menu will appear as far as you never tried the playback. ) to play the data recorded in HDD.
SHR-2040/2041/2042-ENG-1013 10/19/07 10:25 AM Page 8-9 SHR-2040/2041/2042 USER’S MANUAL ● Definition Play Screen Mode 4 Split Screen Single Screen PIP Screen 6 Split Screen 9 Split Screen ① 4 Split Screen : If you select more than a channel, 4 Split Screen will appear. ➁ Single Screen : This appears when you select one channel in Search. If you press the [CH1~CH4] button in the other split screen, the selected channel appears with the single screen.
SHR-2040/2041/2042-ENG-1013 ● 10/19/07 10:25 AM Page 8-10 Play at Faster Speed If you press the LEFT or RIGHT button( ¦¦ / ) during the playback, you will be able to see the screen at the x2, x4, x8, x16, x32, and x64 speed either forwardly or reversely. ● Viewing Still Screen If you press the LEFT or RIGHT button( ¦¦ / ) when the system paused, you will be able to see still screens forwardly or reversely.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 1
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9 Chapter 9 Smart Viewer
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-1 SHR-2040/2041/2042 USER’S MANUAL 1 Introduction Smart Viewer is a program that a general PC user is able to install SHR-2040/2041/2042 to his PC to monitor the video and audio data in the real time through network without going to the site where SHR-2040/2041/2042 is installed.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-2 2 Feature ● Thanks to the transmission of video data compressed by the MPEG-4 Video Compression method, it can play the video images of good quality. ● Thanks to the G.726 Voice Compression method, it supplies the voice data of good quality. Use of armored MIC improves the quality of remote voice.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-3 SHR-2040/2041/2042 USER’S MANUAL 3 PC Specification(Recommendation) ● OS : Win2000, WinXP ● Recommendation : CPU Pentium 3, 1GHz or higher RAM 256 MB or higher VGA RAM 32Mb or higher DirectX 8.1 or higher Note Depending on Recording Rate, Video Size, and user’s PC specification set to SHR-2040/2041/2042, the number of Smart Viewer playback frame varies. For the detailed specification, refer to Appendix 4.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-4 4 Smart Viewer Installation Smart Viewer Installation ● Put a Smart Viewer Program CD in CD-ROM and open the “Smart Viewer” folder in the CD. ● Run the “Setup.exe” file.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-5 SHR-2040/2041/2042 USER’S MANUAL 9-5 English ● Click the “Next” button. ● If you agree with Smart Viewer License, click “Yes”. ● Designate a folder to install Smart Viewer in it and click “Next”.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-6 ● The system proceeds with setup file installation and system setup. ● Installation is complete. Click the “Finish” to terminate the installation.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-7 SHR-2040/2041/2042 USER’S MANUAL 5 Smart Viewer Program Execution ● 9-7 English Double-click the Smart Viewer icon in the background screen to run the program.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-8 6 Smart Viewer Initial Screen ● Screen Description 2 1 3 4 6 5 7 8 11 9 10 12 13 14 ! This is the button to enter the Search mode in which you can search and play remote the video file recorded in SHR-2040/2041/2042 and enter the Monitoring mode for real-time video monitoring. @ This button terminates or minimizes the program. # It displays the current date, day, and time.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-9 SHR-2040/2041/2042 USER’S MANUAL 7 Monitoring Mode ● DVR(SHR-2040/2041/2042) / SITE Connection - Select the name of DVR(SHR-2040/2041/2042) or site for connection and click the connection button. Note You can set the name, IP, and password of DVR (SHR-2040/2041/2042) for connection in the Setup mode. Also, the site setup which permits simultaneous connection to multi-DVRs (SHR-2040/2041/2042) is available in the Setup mode.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-10 Note No more than 3 users, one Admin. authorized user and 2 User authorized users are allowed to access SHR-2040/2041/2042 simultaneously.(In the case of multicast, 5 User authorized users are allowable.) Caution Once occupied by 3 users( In the case of multicast, 6 users), SHR-2040/2041/2042 does not permit more connection.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-11 SHR-2040/2041/2042 USER’S MANUAL ● Time Information - As soon as you are connected to SHR-2040/2041/2042, the current date, day, and time of SHR-2040/2041/2042 will be displayed. - Otherwise, the current date, day, and time of your PC will be displayed. ● Connection Information - As soon as you are connected to SHR-2040/2041/2042, the connection button will display connection status.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-12 Note # Clicking the speaker icon turns the audio of channel on or off. : Audio OFF : Audio ON If you turn the audio of a SHR-2040/2041/2042 channel off, “Disable” will be displayed. : Audio Disabled ✴ For the Audio on channel now, use the following audio button to adjust the volume and set the mute.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-13 SHR-2040/2041/2042 USER’S MANUAL ● Event Log Display Window - Click the Log button to activate the log display window. - It displays the event(alarm, user connection, and setup change) occurring at SHR-2040/2041/2042 in the real-time. Note [Event Message] Connecting.. : Trying to connect to SHR-2040/2041/2042. Connected.. : Succeeded connecting to SHR-2040/2041/2042. Connection Failed : Failed in connecting to SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-14 Caution When Time Change, Load Factory Default, Network Change, System Shutdown, or Hdd Format event occurs, Smart Viewer terminates the connection automatically. ● Camera connection Indication Window - Displays the connection condition of DVR and CAMERA in the list. Note [DVR Icon Color] Successfully connected to SHR-2040/2041/2042, the icon turns yellow, otherwise, turns black.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-15 SHR-2040/2041/2042 USER’S MANUAL ● Screen Split Selection Button - Full Screen / Single / Quad / Nine-Split / Sixteen-Split Mode - You can change the Split Mode of the screen under monitoring. ● Sequence Mode Button - Changes the channel to be played at the preset interval. - The sequence time interval can be set at the Setup Mode ➝ Viewer Setup.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-16 : When monitoring with Quad Mode : When monitoring with Single Mode : Camera Off Note The number in the screen icon indicates the screen position in SmartViewer. : The orange icon indicates the current channel is connected to a camera. : The gray icon indicates the current channel is connected to a camera but not displayed in the screen. : The black icon with a slash indicates the current channel is not connected to any camera.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-17 SHR-2040/2041/2042 USER’S MANUAL ● NEXT Button - Click the NEXT(Mouse Left Button) to see the channel next to the current channel. In Single Mode : 1 ➝ 2 ➝ 3 ➝ 4 ➝ 1 (CH) In Quad Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) In Nine-Split Mode : 1,2,3,4 ➝ 1,2,3,4 (CH) In Sixteen-Split Mode : 1,2,3,4 ➝1,2,3,4 (CH) Note If you connected with multi-DVRs(SHR-2040/2041/2042) through a site, the sequence will operate as follows. - In Single Mode : DVR1:3CH ➝...
SHR-2040/2041/2042-ENG-2 10/19/07 ● 10:37 AM Page 9-18 FAVORITE Button - If you press FAVORITE, the FAVORITE window will be activated. a a b b c c d d If you click the current FAVORITE, the cameras saved in the current setting value will be displayed in the screen. You may delete the selected FAVORITE or all FAVORITE setting values. You may set up a new FAVORITE number and name. Change FAVORITE at the set intervals. Note - The FAVORITE button is available only when you contact SITE.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-19 SHR-2040/2041/2042 USER’S MANUAL ● Video Recording Button - If you select a channel in the playback and click the “Save” button, the video will be saved in a file format with the extension of *.dvr in a designated folder of your PC. - The name of the directory in which an image will be saved, the file name, and the image save length shall be set up at the Setup Mode ➝ Viewer Setup.
SHR-2040/2041/2042-ENG-2 10/19/07 ● 10:37 AM Page 9-20 PTZ Camera Control Buttons - Select a channel connected to PTZ Camera to control PTZ related functions. - PAN Left / Right - TILT Up / Down - Diagonal Control - The channel under PTZ control will be displayed in the center of the button. 3 1 2 !@ ZOOM IN / OUT # POWER ZOOM : Click P button to activate POWER ZOOM. - POWER ZOOM is a function to zoom in or zoom out the video screen by clicking the screen.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-21 SHR-2040/2041/2042 USER’S MANUAL ! PRESET - If you press the PRESET button, a window for PRESET setup pops up. a If you click the current PRESET number and a name, the camera will move to its position. b b You can delete the selected or all the PRESET setup values. c c You can set a new PRESET number and name. Note ! The PRESET function is supported to all the cameras. You are allowed to set no more than 20 PRESET items.
SHR-2040/2041/2042-ENG-2 10/19/07 ● 10:37 AM Page 9-22 Self Menu Setup of PTZ device 1 ! You can set the function menu in the PTZ camera. 1 2 3 ! This is a Menu screen supplied by the camera itself, seen from Viewer. @ Use the / / / button for the movement between menus. # This is a button for the role of Enter. Note The Camera Menu Setup function is supported by Samsung and Panasonic camera only.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-23 SHR-2040/2041/2042 USER’S MANUAL 8 Search Mode ● The initial screen of search mode - The search mode is divided into the remote mode to search and play the SHR-2040/2041/2042 video and the local mode to play *.dvr file saved in the directory designated by your PC. 1 3 4 2 5 6 7 8 10 11 9 12 ! To change to the search mode for the remote control of video recorded in SHR-2040/2041/2042. @ To show the playback video.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-24 ● DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE - Same as “DVR(SHR-2040/2041/2042)/SITE Connection” of the monitoring mode. ● DVR(SHR-2040/2041/2042) Selection/Change by contacting SITE - Select SHR-2040/2041/2042 from the Contact list. - SHR-2040/2041/2042 turns black if contacted with the ADMIN authority and turns gray if contacted with the USER authority. - Without the ADMIN authority, search is not accessible.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-25 SHR-2040/2041/2042 USER’S MANUAL ● Calendar Window - If the video data in on-line SHR-2040/2041/2042 is recorded, the date turns red. - If you click the date in red, the saved video information is displayed. - The currently selected date will be marked with a thick red box. - ¦ : Moves to the previous month. - : Moves to the next month.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-26 Backup Button - If not playback(Stop), the video save button performs the backup function. - If the save button is pressed, the window for backup pops up. - Set a Start/End tome for backup and select a file format to save. - The backup starts when the “Start” button is clicked. The backup file is saved according to the setting route; Setup ➞ Viewer Setup ➞ Video Recording ➞ Video Location. - To stop the backup, click the “Stop” button.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-27 SHR-2040/2041/2042 USER’S MANUAL # Print - This function outputs the screen zone of the playback video which is now being displayed. $ Setup Mode Button - This button pops up the setup mode window. ● Play Buttons 2 1 5 9 3 7 4 6 8 ! Play : Play @ Reverse Play : Reverse Play # Stop : Stop $ Fast Forward : Faster Play % Fast Backward : Faster Reverse Play ^ Step Forward : Forward playback per second.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-28 Note During the play(Play/RevPlay/FF/FB), disconnection or change to the both monitoring mode and local mode is not permitted. Click the Stop button first before the change. ● Time Line - Displays the time information of video in SHR-2040/2041/2042 selected on the calendar window. - The normal mode indicates the time information of 24 hours while the Extension mode indicates the time information every 2 hours.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-29 SHR-2040/2041/2042 USER’S MANUAL ● Next Button - Changes the channel as the Next button does in the monitoring mode. Note During the video playback(Play/RevPlay/FF/FB), the channel change is not available. ● Reload Button - Updates the record time information in the calendar window and time line. ● Local Mode - Plays *.dvr file saved in the directory of your PC by the Record function. - You can search and play only one channel.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-30 9 Setup Mode ● Initial Screen 3 1 2 4 ! Button to select items for DVR Setup, Viewer Setup, Site Setup, and S/W Version setup. @ It shows what the selected Setup item can set up in detail. # button to terminate the setup window. $ Button to save the information revised in the setup window, remark the information prior to such a revision, or terminate the setup window.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-31 SHR-2040/2041/2042 USER’S MANUAL ● Setup Item Selection Button - It is used for the selection of each setup item. - It is composed of 4 items-DVR Setup, Viewer Setup, Site Setup, and S/W Version. - DVR Setup : Allows you to change the remote menu setup items of SHR-2040/2041/2042. - Viewer Setup : Allows you to set the various kinds of item concerning the operation of Smart Viewer.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-32 DVR Setup - Click the [DVR Setup] button for DVR Setup. - You can change remotely the setup items of SHR-2040/2041/2042 Menu, being connected with Smart Viewer. - DVR Setup is composed of 5 items; System, Camera/Audio, Monitoring, Recording, and Network. Note - You are authorized with access to DVR Setup in an Admin authority only. - The button will not be activated if you are connected to SHR-2040/2041/2042 as a user or unconnected.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-33 SHR-2040/2041/2042 USER’S MANUAL ● Detailed DVR Setup Items ! System - Information Information shows the information on on-line SHR-2040/2041/2042. Note For the detailed items of DVR Setup, refer to Chapter 5. - Admin Password You can change the Admin password related settings for control of DVR. - User Password You can change the user password related settings for control of DVR.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-34 Caution System Password shall be composed of numeric only, up to 8 digits. Note - The Delete key and the combination of Ctrl+C or Ctrl+V in the keyboard are not supported at the System Password input. - Use the BACKSPACE key to delete the contents. Note Default System Password is set to 4321. - Date/Time Data/Time is used to set the information of Date, Time, Format, and DST for on-line SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-35 SHR-2040/2041/2042 USER’S MANUAL - Language Language sets the language in which on-line SHR-2040/2041/2042 will be expressed Note The change of language by the system language results in the change of language expression setup of SHR-2040/2041/2042. In short, the language setup of Smart Viewer does not change. Language specification to be supported is subject to change later.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-36 - Remocon (Remote Control Device) Remocon can set the remote control device installed to SHR-2040/2041/2042. Note If you install the remote control device to the main body of SHR-2040/2041/2042 and activate the setup, PTZ control is not available in the Viewer.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-37 SHR-2040/2041/2042 USER’S MANUAL @ Camera - Config. Config. sets Video, Audio On/Off, Camera Title, and Auto Sequence Time for each channel of on-line SHR-2040/2041/2042. Caution - Only English is supported for the title. If you type in and apply the title in your native language, warning message pop sup to ask your retyping. - The title should be composed of no more than 15 digits.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-38 - PTZ device It sets Camera ID, Protocol, Baud Rate, Parity, Data Bit, Stop Bit, and Serial Mode when connecting the dome camera to all the channels. # Monitoring - Monitoring It sets both the event monitoring and OSG display of the live mode.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-39 SHR-2040/2041/2042 USER’S MANUAL $ Recording - Rec. Mode It sets the Video Size, Quality, and Rate values during the recording by the setting the recoding ON/OFF for the related channel in the live mode. NTSC PAL Note Full D1(L) Video Size does not support 15.00ips, 10.00ips (NTSC) / 12.50ips, and 8.33ips(PAL) Rate. - Video size Rec. Sets the Video size. The Video size being set in the menu affects to the ips setup of Rec. Mode and Event Rec.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-40 - Event Rec. It sets the Video Size, Quality, Rate, Pre Alarm, and Post Alarm values to be recorded when an event occurs. NTSC PAL Note Full D1(L) Video Size does not support 15.00ips, 10.00ips(NTSC) / 12.50ips, and 8.33ips(PAL) Rate.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-41 SHR-2040/2041/2042 USER’S MANUAL - Alarm Rec. It sets the information necessary for the alarm recording. Note More than one camera should be selected to apply the alarm. - Motion Rec. It sets the information necessary for the recording by the motion Detection.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-42 - Video Loss Video Loss sets up the information on how to inform the user of Video Loss of SHR-2040/2041/2042. % Schedule You can configure schedule-related settings. - Record Schedule You can change the schedule recordingrelated settings.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-43 SHR-2040/2041/2042 USER’S MANUAL - Alarm Out Schedule You can change the alarming schedulerelated settings.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-44 ^ Network - Password It sets the password for Admin and User when connecting with SHR-2040/2041/2042 through the network in Smart Viewer. ● Double-click the Smart Viewer icon in the background screen to run the program. Caution - Network password should be composed of numeric and it can be input up to 8 digits. - If you leave password blank and apply it, a warning message pops up to ask your retyping.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-45 SHR-2040/2041/2042 USER’S MANUAL - IP Settings It sets the network connection method of SHR-2040/2041/2042. SHR-2040/2041/2042 supports the connection with Static IP, Dynamic IP, and ADSL(PPPoE). It can set the network bandwidth. Adjust the bandwidth to the network condition in which SHR-2040/2041/2042 is connected. It sets the IP Address, Gateway, Subnet Mask, and DNS. Input both ID and password of the sub scriber for ADSL.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-46 ● Transfer Protocol - You can change the transfer protocol setting value. The protocol supports TCP/IP and UDP(Unicast, Multicast). Control Port(TCP/IP) and Port(UDP) to alter the connection port. Both Multicast IP and TTL are used for UDP(Multicast). ● Callback - You can set the Callback function of SHR-2040/2041/2042.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-47 SHR-2040/2041/2042 USER’S MANUAL Note - SHR-2040/2041/2042 uses 4 ports for TCP connection. - The PORT number is flexible and 4 consecutive numbers are grouped for the change ( 554,555,556,557 ➝ 558,559,560,561 ) - If you use the IP Router for network composition, you should allocate a protocol for SHR-2040/2041/2042. Viewer Setup - Click the [Viewer Setup] for Viewer Setup.
SHR-2040/2041/2042-ENG-2 10/19/07 ● 10:37 AM Page 9-48 Video Recording ! Naming - Being connected to SHR-2040/2041/2042 in the monitoring or search mode, you can save the video displayed with *.dvr file and name it. - If you set to “Camera No. + Serial No.”, the file name depends on the camera number and serial number. If set to “Camera No. + Date”, it depends on the camera number, current date, and time.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-49 SHR-2040/2041/2042 USER’S MANUAL ● Sequence Time - When connecting with SHR-2040/2041/2042 in the monitoring mode, set the auto sequence time if the auto sequence is set. The time can be set from 10 to 20 minutes. ● OSD Display - Sets if OSD shall be displayed on each channel of Smart Viewer. - Whether you check “Enable” or not, OSD will appear or not.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-50 Site Setup - Click the [Site Setup] button for Site Setup. - The information of DVR(SHR-2040/2041/2042) or Site that you want to connect by Smart Viewer is set in the Site Setup. - Smart Viewer allows you to connect with DVR(SHR-2040/2041/2042) or Site registered only here. 1 3 5 2 4 ! The DVR(SHR-2040/2041/2042) list that registered by the user is displayed.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-51 SHR-2040/2041/2042 USER’S MANUAL ● DVR List - The information of DVR(SHR-2040/2041/2042) that you want to connect by Smart Viewer is set in the DVR List. - You can register a new DVR(SHR-2040/2041/2042) or delete and edit the DVR(SHR-2040/2041/2042) selected from the registered list, and the name and IP / MAC Address of the registered DVR(SHR-2040/2041/2042) is displayed in DVR List.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-52 - If your DVR (SHR-2040/2041/2042) uses a static IP, select “Static IP” for Address Type and type in the name of the DVR (SHR-2040/2041/2042) and the IP address. - Select “Port” so that it matches the port number that you’ve set in the network menu of DVR (SHR-2040/2041/2042).
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-53 SHR-2040/2041/2042 USER’S MANUAL - If you select “Use DDNS” in the network settings menu of DVR (SHR-2040/2041/2042) or use an IP splitter to register an URL using DDNS, you can make connection via the URL. - If you want to make connection via the an URL, select “URL” for Address Type and type in the URL set for the DVR or IP splitter in the URL menu item.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-54 Note - The MAC address of DVR is written at the side label of the product. It is also found in the system information of DVR Menu. - If the DVR(SHR-2040/2041/2042) is connected to ADSL, the network bandwidth is low. Therefore, the transfer rate becomes low and the viewer operates in the more limited range. - The viewer can monitor up to 4CH all the same time. - The viewer can search or play only 1CH. - The audio does not play.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-55 SHR-2040/2041/2042 USER’S MANUAL # To Edit the old DVR(SHR-2040/2041/2042) - If you select a DVR(SHR-2040/2041/2042) in the DVR list to edit and press the [Edit] button, the following message box pops up. Press [OK] button to edit the DVR(SHR-2040/2041/2042). - When the DVR(SHR-2040/2041/2042) to edit is connected with the Smart Viewer, the following message box pops up and the DVR(SHR-2040/2041/2042) cannot be edited.
SHR-2040/2041/2042-ENG-2 10/19/07 ● 10:37 AM Page 9-56 Site List - You can register and control the many DVRS(SHR-2040/2041/2042) to be connected with the smart viewer at once with a site in the site list. You are allowed to register a new site, and delete or edit the selected site in the registered list. Also, you can add or delete a DVRS(SHR-2040/2041/2042) to the site selected in the site list.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-57 SHR-2040/2041/2042 USER’S MANUAL @ To delete an old site or DVR(SHR-2040/2041/2042) - If you select a site or DVR(SHR-2040/2041/2042) in the site list for deletion and press the [Delete] button, the following message box pops up. Press the [OK] button to delete either site or DVR(SHR-2040/2041/2042). - When deleting the DVR(SHR-2040/2041/2042), it is deleted from the site composition but the DVR(SHR-2040/2041/2042) information is not deleted.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-58 - When the site to edit is connected with the Smart Viewer, the following message box pops up and the site cannot be edited. Be sure to cut the connection between the DVR(SHR-2040/2041/2042) and the Smart Viewer before you edit it. - If you select a DVR(SHR-2040/2041/2042) and press the [Edit] button, the following message box pops up and the DVR(SHR-2040/2041/2042) cannot be edited. To edit the DVR(SHR-2040/2041/2042), go to the DVR list.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-59 SHR-2040/2041/2042 USER’S MANUAL S/W Version - If you press the [S/W Version] button, the smart viewer version, system requirements, and the version of DVR(SHR-2040/2041/2042) System S/W, being connected to the smart viewer, are displayed. - You can upgrade the on-line DVR(SHR-2040/2041/2042) System S/W remotely. You are authorized with S/W upgrade in an Admin authority only.
SHR-2040/2041/2042-ENG-2 10/19/07 ● 10:37 AM Page 9-60 Smart Viewer Version - Smart Viewer Version and system requirements are displayed. ● DVR Version SHR-2040/2041/2042 - DVR Version not only displays the connected DVR(SHR-2040/2041/2042) name if any DVR(SHR-2040/2041/2042) is being connected with Smart Viewer or the name of DVR(SHR-2040/2041/2042) composing a site if any DVR(SHR-2040/2041/2042) is being connected with the site but also displays DVR(SHR-2040/2041/2042) S/W version.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-61 SHR-2040/2041/2042 USER’S MANUAL @ Click the following button to open the “SHR-2040/2041/2042 Firmware” file in format. 2040/2041/2042 2040/2041/2042 # Press the [Upgrade] button to transmit a file to the selected DVR(SHR-2040/2041/2042) and start the upgrade of DVR (SHR-2040/2041/2042) S/W. $ The progress of file transmission and upgrade is displayed at the bottom.
SHR-2040/2041/2042-ENG-2 ● 10/19/07 10:37 AM Page 9-62 Extracting the settings for DVR(SHR-2160/2160/2080/2082) - SmartViewer enables you to extract the menu settings for the connected DVR(SHR-2160/2160/2080/2082). ! Select the DVR you want to extract the setting values from. @ Press the [Export] button to specify the file name (*.dat), then the setting values can be saved on your PC.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-63
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 9-64 Appendix
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-1 SHR-2040/2041/2042 USER’S MANUAL 1 Product Specification Item Details OS Broadcasting Input Voltage Embedded OS NTSC/PAL System 2040-DC 12V, AC 110-220(NTSC), AC 100-230(PAL) 2041/2042 - AC 110-220(NTSC) AC 100-230(PAL) Power Consumption 2040 : 30Watt, 2041 : 60Watt, 2042 : 51Watt Composite 4 Channel - 1.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-2 Item Details Compression Method Video Size & Performance Remarks Video : MPEG4 Audio : ADPCM Resolution Quality Level Max Image Rate CIF(C) 352X240(NTSC) /352X288(PAL) Very High High Standard Low 30.00ips(NTSC)/ 25.00ips(PAL) Half D1(N) 720X288(NTSC) /720X288(PAL) Very High High Standard Low 15.00ips(NTSC)/ 12.50ips(PAL) Full D1(L) 720X480(NTSC) /720X576(PAL) Very High High Standard Low 30.00ips(NTSC)/ 25.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-3 SHR-2040/2041/2042 USER’S MANUAL Item Search Mode Video size & Performance Play Back Display Mode Play Mode Backup Alarm Network Serial I/F PC Spec. Remote Viewer Support OS Function Operation Temp. Preservation Temp.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-4 2 Outline Drawings [SHR-2040] [SHR-2041] English 10-4
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-5 SHR-2040/2041/2042 USER’S MANUAL [SHR-2042] 10-5 English
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-6 3 Factory Default This restores the Network information and preset values in SHR-2040/2041/2042 to the original state at the time of factory shipment. Factory Default will be done as follows; - Use System / Load Factory Default in MENU or, - If you hold on to the Mode button in Live Mode and keep pressing the CH2 button for 5 seconds, the system will return to the Factory default condition. The front button repeats the flickering.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-7 SHR-2040/2041/2042 USER’S MANUAL Classification Detailed Items Factory Setup Duration Off Event Monitoring Date On OSD Display Time On Title On Status On Monitoring Spot Out Channel CH1 Spot Out Event Monitor Off Monitor Out Composite Out 1CH DVR Support Off Record Mode Setup Mode On Video Size CIF Quality Standard 30ips(NTSC)/25ips(PAL) Rate Record Schedule Continuous Recording Off Event Recording On Video Size Vi
SHR-2040/2041/2042-ENG-2 10/30/07 5:35 PM Page 10-8 Classification Detailed Items IP Settings Network Transfer Protocol Settings Callback Settings Factory Setup Connection Mode Static IP Bandwidth 2Mbps Admin Password 4321 User Password 4321 IP 192.168.001.200 Gateway 192.168.001.001 Subnet Mask 255.255.255.000 DNS 168.126.063.001 ADSL User ID ID Password - Protocol type UDP Port(TCP) 0554.0555.0556.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-9 SHR-2040/2041/2042 USER’S MANUAL 4 SHR-2040/2041/2042 Smart Viewer Frame Specification for the Playback NTSC FRAME RATE 15 10 7.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-10 PAL FRAME RATE 12.5 8.33 6.25 5 2.5 1 Viewer Screen Split Mode VIDEO SIZE Half D1(N) CIF (C) Nine-split 1 frame/sec 12.5 frame/sec Fore-split 12.5 frame/sec 12.5 frame/sec Single 12.5 frame/sec 12.5 frame/sec Half D1(N) CIF (C) Nine-split 8.33 frame/sec 8.33 frame/sec Fore-split 8.33 frame/sec 8.33 frame/sec Single 8.33 frame/sec 8.33 frame/sec Half D1(N) CIF (C) Nine-split 6.25 frame/sec 6.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-11 SHR-2040/2041/2042 USER’S MANUAL 5 Troubleshooting(FAQ) 1. The system power is dead and LED in front of the system does not operate at all. - Please check the power connection. - Check the power voltage. - If all your efforts like above end up with nothing, check or exchange the power supply. 2. Video data remains in the system but some channels displays no video data but turns all blue. - Check the image of the camera connected to the system.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-12 8. The cursor cannot reach Start during Calendar Search. - Please check both the channel and the date for play are left checked. Both shall be checked for play with Start. The cursor cannot reach the unrecorded date. 9. Alarm, once issued, keeps being issued though you press the front Alarm button for cancellation. - Press the front Menu button to cancel Alarm as follows.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-13 SHR-2040/2041/2042 USER’S MANUAL 14. Smart Viewer in operation is disconnected. - If you change time, network setup, HDD format, Default Setup, or HDD attachment or detachment for SHR-2040/2041/2042 DVR, the current Smart Viewer will be automatically disconnected. - Check network connection. Smart Viewer, if disconnected from Network, will try reconnection up to 5 times.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-14 6 Open source license report on the product This product uses software provided under the name of GPL and LGPL. You can receive the following GPL and LGPL source codes by email request to www.sec.co.kr. - GPL Software Kernel, Busybox, Sysvinit, dvd+rw-tools, cdrtools, dosfstools - LGPL Software gLibc, Inetutils GNU GENERAL PUBLIC LICENSE Version 2, June 1991 Copyright (C) 1989, 1991 Free Software Foundation, Inc.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-15 SHR-2040/2041/2042 USER’S MANUAL containing the Program or a portion of it, either verbatim or with modifications and/or translated into another language. (Hereinafter, translation is included without limitation in the term "modification".) Each licensee is addressed as "you". Activities other than copying, distribution and modification are not covered by this License; they are outside its scope.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-16 the terms of Sections 1 and 2 above on a medium customarily used for software interchange; or, b) Accompany it with a written offer, valid for at least three years, to give any third party, for a charge no more than your cost of physically performing source distribution, a complete machine-readable copy of the corresponding source code, to be distributed under the terms of Sections 1 and 2 above on a medium customarily used for software interchange;
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-17 SHR-2040/2041/2042 USER’S MANUAL invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply and the section as a whole is intended to apply in other circumstances.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-18 BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE PROGRAM TO OPERATE WITH ANY OTHER PROGRAMS), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-19 SHR-2040/2041/2042 USER’S MANUAL License, version 2, hence the version number 2.1.] Preamble The licenses for most software are designed to take away your freedom to share and change it. By contrast, the GNU General Public Licenses are intended to guarantee your freedom to share and change free software--to make sure the software is free for all its users.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-20 we use the ordinary General Public License for many libraries. However, the Lesser license provides advantages in certain special circumstances. For example, on rare occasions, there may be a special need to encourage the widest possible use of a certain library, so that it becomes a de-facto standard. To achieve this, non-free programs must be allowed to use the library.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-21 SHR-2040/2041/2042 USER’S MANUAL forming a work based on the Library, and copy and distribute such modifications or work under the terms of Section 1 above, provided that you also meet all of these conditions: l a) The modified work must itself be a software library. l b) You must cause the files modified to carry prominent notices stating that you changed the files and the date of any change.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-22 even though third parties are not compelled to copy the source along with the object code. 5. A program that contains no derivative of any portion of the Library, but is designed to work with the Library by being compiled or linked with it, is called a "work that uses the Library". Such a work, in isolation, is not a derivative work of the Library, and therefore falls outside the scope of this License.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-23 SHR-2040/2041/2042 USER’S MANUAL ■ If distribution of the work is made by offering access to copy from a designated place, offer equivalent access to copy the above specified materials from the same place. ■ Verify that the user has already received a copy of these materials or that you have already sent this user a copy.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-24 directly or indirectly through you, then the only way you could satisfy both it and this License would be to refrain entirely from distribution of the Library. If any portion of this section is held invalid or unenforceable under any particular circumstance, the balance of the section is intended to apply, and the section as a whole is intended to apply in other circumstances.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-25 SHR-2040/2041/2042 USER’S MANUAL TIAL DAMAGES ARISING OUT OF THE USE OR INABILITY TO USE THE LIBRARY (INCLUDING BUT NOT LIMITED TO LOSS OF DATA OR DATA BEING RENDERED INACCURATE OR LOSSES SUSTAINED BY YOU OR THIRD PARTIES OR A FAILURE OF THE LIBRARY TO OPERATE WITH ANY OTHER SOFTWARE), EVEN IF SUCH HOLDER OR OTHER PARTY HAS BEEN ADVISED OF THE POSSIBILITY OF SUCH DAMAGES.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-26 * "This product includes software developed by the OpenSSL Project * for use in the OpenSSL Toolkit. (http://www.openssl.org/)" * * 4. The names "OpenSSL Toolkit" and "OpenSSL Project" must not be used to * endorse or promote products derived from this software without * prior written permission. For written permission, please contact * openssl-core@openssl.org. * * 5.
SHR-2040/2041/2042-ENG-2 10/19/07 10:37 AM Page 10-27 SHR-2040/2041/2042 USER’S MANUAL * in documentation (online or textual) provided with the package. * * Redistribution and use in source and binary forms, with or without * modification, are permitted provided that the following conditions * are met: * 1. Redistributions of source code must retain the copyright * notice, this list of conditions and the following disclaimer. * 2.
SHR-2040/2041/2042-ENG-2 10/19/07 5:58 PM Page 10-28 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.