Dishwasher Installation manual DW80R706* Series DW8000R_DD68-00210A-00_EN.
Contents Contents Safety instructions 3 Important safety instructions Before using your dishwasher 3 5 Installation 6 Product dimensions Cabinet dimensions 11 12 Specifications 34 Scan the QR code* to view our helpful installation videos. * Requires reader to be installed on your smartphone. 2 English DW8000R_DD68-00210A-00_EN.
Safety instructions Throughout this manual, you will see Warning and Caution notes. The warnings, cautions, and the important safety instructions that follow do not cover all possible conditions and situations that may occur. It is your responsibility to use common sense, caution, and care when installing, maintaining, and operating the dishwasher. Samsung is not liable for damages resulting from improper use.
Safety instructions California Proposition 65 Warning WARNING: Cancer and Reproductive Harm - www.P65Warnings.ca.gov Read all instructions before using the appliance. Install and store the dishwasher inside, away from exposure to weather. CAUTION • • • Safety instructions • Do not install the dishwasher near electrical components. Keep the dishwasher away from open flames. Do not install the dishwasher on a carpet as this is a fire hazard.
Make sure to use a new water supply line. Old lines are susceptible to breakage because they become hardened and may cause property damage due to a water leakage. The dishwasher must be connected to a hot water supply with a temperature between 120 °F (49 °C)~149 °F (65 °C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 °F (65 °C) to prevent damage to dishes. Ensure that the water supplied to the dishwasher does not freeze.
Installation Be sure that you or your installer follow these instructions closely so that the new dishwasher works properly and that you are not at risk of injury when washing dishes. STEP 1 Check the parts and tools Before starting on the installation, prepare all the necessary tools and parts required to install the dishwasher. This will save installation time and simplify the installation process. Parts required Provided with the dishwasher. Check when you unbox the dishwasher in STEP 5.
Not provided Power cable Twist on wire connector Strain relief Electrical tape & Standard duct tape Hot water supply line 90° Fitting (3/4") Tube fittings Hose clamp Air gap Rubber connector NOTE [Warning: Do not use plastic tubing. Plastic tubing can deteriorate over time and cause a leak inside the tube fitting.] You also need a 90° Fitting with 3/4" N.P.T.
Installation Tools required Installation Electric drill Safety glasses Gloves Flashlight Adjustable wrench Wire stripper Pliers Nipper Tape measure Pencil Phillips screwdriver Flat screwdriver Tubing cutter Cutting knife Hole saw Level Torx t20 Hex L-wrench 8 English DW8000R_DD68-00210A-00_EN.
NOTE New installation If the dishwasher is a new installation, most of the installation work must be done before the dishwasher is moved into place. Replacement If the dishwasher is replacing an old dishwasher, you must check the exising dishwasher connections for compatibility with the new dishwasher. Replace the existing connections as necessary.
Installation If this is a new installation, follow these steps: 1. Using a 21/2 inch hole saw, cut a hole into the side of the cabinet that holds the sink as shown in Figure 1-1 below. 2. If the base inside the sink cabinet is raised above the kitchen floor and is higher than the connections on the dishwasher, make a hole in the base inside the cabinet and in the cabinet side as shown in Figure 1-2. NOTE Depending on where your electrical outlet is, you may need to cut a hole in the opposite cabinet side.
Product dimensions Front view DW80R7060 Series DW80R7061 Series 237/8" (605 mm) 237/8" (605 mm) 33⅞-35" (860-890 mm) 33⅞-35" (860-890 mm) Junction box Junction box Side view Installation DW80R7060 Series DW80R7061 Series 275/16" (693 mm) 21/2" (60 mm) 53/4" (140 mm) 41/5" (107 mm) 21/2" (60 mm) 23/4" (70 mm) 201/2" (520 mm) 25" (636 mm) 201/2" (520 mm) 25" (636 mm) You must arrange the water supply line, power cable and drain hose in the space behind the dishwasher.
Installation Cabinet dimensions NOTE 24" (610 mm) minimum 34⅛-35⅓" (867-897 mm) 24" (610 mm) minimum This dishwasher is designed to be enclosed on the top and on both sides by a standard residential kitchen cabinet unit. The installation cabinet must be clean and free of any obstructions. The cabinet must be at least 24 inches wide, 24 inches deep, and 341/8 inches high.
STEP 3 Check water supply requirements and cautions • • The hot water supply line pressure must be between 20~120 psi (140~830 kPa). Adjust the water heater to deliver water between 120 °F (49 °C)~149 °F (65 °C). - - The dishwasher must be connected to a hot water supply between 120 °F (49 °C)~149 °F (65 °C). This temperature range provides the best washing result and shortest cycle time. Temperature should not exceed 149 °F (65 °C) to prevent damage to dishes.
Installation STEP 4 Check the electrical requirements and cautions The electrical requirements for the dishwasher are as follows: • • • In the United States, install in accordance with the National Electric Code/State and Municipal codes and/or local codes. In Canada, install in accordance with the Canadian Electric Code C22.1-latest edition/ Provincial and Municipal codes and/or local codes. For cable direct connections.
STEP 5 Unpacking and inspecting the dishwasher Unpack the dishwasher in an open area free of obstruction both around the packaging and overhead. We recommend that you retain all of the packing materials until the dishwasher is fully installed and operational to ensure you have removed all the product’s components from the packing materials prior to disposal. Unpacking 1. Position the carton right-side-up with top arrows pointing upwards. 2. Unbuckle or cut the straps securing the packaging. 3.
Installation Inspecting Mechanical 1. Check the plastic base assembly to ensure that it is intact 2. Check the dishwasher’s feet to ensure they are in place and can be adjusted so you can level and secure the dishwasher. 3. Check all the visible components on the bottom of the dishwasher to ensure they are intact and secure. 4. Check the door latch, the operation of the hinges, and confirm the door is properly secured to the dishwasher. Plumbing 1.
STEP 6 Preparing the dishwasher 1. Attach the protective sticker (A). - To prevent damage, put the protective sticker on the bottom of the counter top as shown in the picture. NOTE • • Before putting the protective sticker, clean the counter top as shown in the picture. For information, the length of the protective sticker is 26 inches (660 mm). A Installation 2. Ensure that the circuit breaker and water supply valve are turned off before proceeding with the following steps.
Installation 3. Use the provided nut connector to connect the water hose to the dishwasher. Follow these steps: 01 02 03 A B E C D F 01 Disconnect the 90° fitting (A) from the hose (B). 02 Remove the seal (C) and the nut (D) from the 90° fitting. 03 From the provided nut connector, separate the seal (E) and the nut (F), and then assemble them to the 90° fitting as shown in the figure. You must insert the smaller side of the seal. 4.
Figure 4 A A A’ A’ C B Junction box Strain relief 90° fitting CAUTION Do not overtighten the 90° Fitting. (Below 280 lb·in (31.6 N·m)) Installation Doing so may damage the water inlet valve and cause a water leak. English 19 DW8000R_DD68-00210A-00_EN.
Installation STEP 7 Placing the dishwasher and connecting the hot water supply line 1. Adjust the three leveling legs at the bottom of the dishwasher after measuring the height of the cabinet opening from under the countertop to the floor. (See STEP 8, Leveling the Dishwasher.) 2. Locate the hot water supply line and the power cable. 3. Place the dishwasher so that the hot water supply line is in the left side and the power cable is in the right channel of the base of the dishwasher.
Figure 5 Side gasket Side gasket Junction box 1 inch Drain hose Hot Water Supply Line Power cable Inlet valve built-in hook Hot Water Supply Line /4" (9.5 mm)) 3 Elbow ( Installation CAUTION Do not overtighten the 90° Fitting. Doing so may damage the water inlet valve and cause a water leak. Make sure the dishwasher is positioned to the center. English 21 DW8000R_DD68-00210A-00_EN.
Installation STEP 8 Leveling the dishwasher 1. Open the door and place the level against the top of the tub on the inside and check if the the dishwasher is level. If it is not level, rotate the leveling legs at the bottom front of the dishwasher until the dishwasher is level. See the first note below for instructions on adusting the height of the front legs. 2. Use the level to check if the dishwasher is level front to back, as shown in the figure to the right.
NOTE • • If the leveling legs are rotated to the left (clockwise), they are loosened and the front of the dishwasher is raised. If they are rotated to the right (counter clockwise), they are tightened and the front of the dishwasher is lowered. You can adjust the leveling legs by a max of 16/32" However, leveling up to the max height is not recommended.
Installation STEP 9 Securing the dishwasher You must secure the dishwasher to the countertop or cabinet side walls for additional stability and safety. To the countertop If the countertop is made of wood or the material will not be damaged by drilling, follow this. 1. Put a large towel into the bottom of the dishwasher(covering the filter) to prevent wood shavings or a dropped screw from falling into the sump. 2. Insert the provided brackets into the top front holes of the dishwasher as shown.
To the sides If the countertop is made of granite, marble, or any other material that can be damaged by drilling, follow this. 1. Put a large towel into the bottom of the dishwasher(covering the filter) to prevent wood shavings or a dropped screw from falling into the sump. 2. Insert the provided brackets into the side front holes of the dishwasher as shown. If the brackets are too long, cut them down using pliers. 3. Pre-drill one hole into both sides of the kitchen cabinet.
Installation Good A Bad B 22" (560 mm) A B 22" (560 mm) Installation Do not to exceed 22" (560 mm) distance between the Caps CAUTION Make sure the tub is not distorted by pressure from the screws. If the tub is distorted, loosen the screws a little. Replace the plastic caps. Use the paper ruler to measure the specified distance on A and B. 26 English DW8000R_DD68-00210A-00_EN.
STEP 10 Securing 1. Check the parts on the sink to which the drain hose will be connected. 2. There are several ways to insert the drain hose into the drain hose connector of the sink, as shown in the following figures. You must connect the drain hose in accordance with the water pipe installation regulations in your region. Figure 8 Case 1. Without disposal Air gap Drain hose Hose clamp Hose clamp Without disposal With an air gap/without disposal Without an air gap Installation Case 2.
Installation 4. Slide a hose clamp over the end of the drain hose. Attach the drain hose to the sink connector, slide the hose clamp to the end of the hose, and then tighten the hose clamp. NOTE You must use a hose clamp. Failure to do so may cause water leakage. 5. To prevent backflow, secure the drain hose to the side or back wall of the kitchen cabinet using cable ties or other fixtures. Make sure the drain hose height is at least 20 inches from the floor. (See Figure 10.) 6.
Figure 9 1 in. (25 mm) /8 in. (16 mm) 5 /8 in. (22 mm) 7 If necessary, cut off the dotted line of the drain hose to fit the size. Figure 10 Sink Min. 30 in. (762 mm) Installation Min. 20 in. (508 mm) Dishwasher To prevent backflow for models without the air gap, secure the drain hose to the side wall of the kitchen cabinet using cable ties or other fixtures. Make sure the drain hose is high at least 30 inches from the bottom. Drain hose English 29 DW8000R_DD68-00210A-00_EN.
Installation STEP 11 Wiring connections 1. Before connecting the power cable to the dishwasher, make sure the circuit breaker is off. 2. In the junction box located at the front bottom right of the dishwasher, find the three power wires from the dishwasher including the grounding line. 3. Pass the power cable through the strain relief, and then into the junction box (Figure 11). 4. Connect the black wire of the dishwasher to the black wire of the power cable by insertng both into a wire nut.
Figure 12 WARNING • Electrical Shock Hazard To avoid electrical shock, do not work on an energized circuit. Doing so could result in serious injury or death. Only qualified electricians should perform electrical work. Do not attempt any work on the dishwasher electric supply circuit until you are certain the circuit is de-energized. • Fire Hazard To avoid a fire hazard, make sure electrical work is properly installed. Only qualified electricians should perform electrical work.
Installation STEP 12 Completing the installation 1. Open the door and remove all foam, paper packaging, and unnecessary parts. 2. Turn on the circuit breaker you turned off before you began the installation. 3. Open the water supply valve to supply water to the dishwasher. 4. Turn on the dishwasher, and then select and run a cycle. CAUTION Make sure to check for water leakage on both ends of the water supply line and drain hose connector. 5.
10. If the “LC” information code continues to appear on the window panel, contact a local service center. 11. Finally, attach the kick plate to the bottom of the dishwasher. While keeping the rubber skirt of the door taut, push the kick plate from the front of the rubber skirt inward underneath the door of the dishwasher. Make sure the gaskets of the kick plate are flush with the floor and side walls. Then, tighten the screws to fix the plate.
Specifications Power supply Water pressure Dimensions 120 V, 15 A, 60 Hz AC 20~120 psi (140 ~ 830 kPa) 237/8 x 25 x 337/8 in. (Width × Depth × Height) Minimum inlet water temperature (605 x 636 x 860 mm) 120 °F (49 °C) NOTE Specifications are subject to change without notice for quality improvement purposes. The actual appearance of the dishwasher may differ from the illustrations in this manual. Specification 34 English DW8000R_DD68-00210A-00_EN.
Memo DW8000R_DD68-00210A-00_EN.
DD68-00210A-00 DW8000R_DD68-00210A-00_EN.
Lavavajillas Manual de instalación Serie DW80R706* DW8000R_DD68-00210A-00_MES.
Contenidos Contenidos Instrucciones de seguridad 3 Instrucciones de seguridad importantes Antes de usar la lavavajillas 3 5 Instalación 6 Dimensiones del producto Dimensiones del gabinete 11 12 Especificaciones 34 Escanee el código QR* para ver videos útiles de instalación. * Debe tener un lector instalado en su teléfono inteligente. 2 Español DW8000R_DD68-00210A-00_MES.
Instrucciones de seguridad A lo largo de este manual, encontrará notas de Advertencia y Precaución. Las siguientes advertencias, precauciones e instrucciones de seguridad importantes no cubren todas las posibles condiciones y situaciones que pueden ocurrir. Es su responsabilidad actuar con sentido común, precaución y cuidado cuando instale, realice el mantenimiento y ponga en funcionamiento la lavavajillas. Samsung no se responsabiliza por los daños ocasionados por un uso inadecuado.
Instrucciones de seguridad Advertencia de la Propuesta 65 de California ADVERTENCIA: Cáncer y daño reproductivo - www.P65Warnings.ca.gov Lea todas las instrucciones antes de usar el electrodoméstico. Instale y guarde la lavavajillas en un lugar interior, no expuesto a los factores climáticos. PRECAUCIÓN • Instrucciones de seguridad • • • No instale la lavavajillas cerca de componentes eléctricos. Mantenga la lavavajillas alejada de llamas abiertas.
Asegúrese de utilizar un conducto nuevo. Los conductos viejos pueden romperse debido a que se endurecen y pueden ocasionar daños materiales por pérdidas de agua. La lavavajillas debe estar conectada al suministro de agua caliente con una temperatura entre 120 °F (49 °C) y 149 °F (65 °C). Este rango de temperatura ofrece un mejor resultado en el lavado y un ciclo más corto. La temperatura no deberá exceder los 149 °F (65 °C) para no dañar la vajilla.
Instalación Asegúrese de que usted o su instalador siga estas instrucciones minuciosamente para que su nueva lavavajillas funcione adecuadamente y no existan riesgos de sufrir lesiones al lavar la vajilla. PASO 1 Verifique las piezas y las herramientas Antes de comenzar la instalación, prepare todas las herramientas y piezas necesarias requeridas para instalar la lavavajillas. Esto ahorrará tiempo y simplificará el proceso de instalación. Piezas necesarias Provistas con la lavavajillas.
No provisto Cable de alimentación Conector de resorte Alivio de tensión Cinta aislante y cinta americana estándar Conducto de suministro de agua caliente Adaptador de 90° (de 3/4") Adaptador del tubo Abrazadera de manguera Espacio de aire Conector de goma NOTA [Advertencia: No utilice tubos de plástico. Los tubos de plástico se pueden deteriorar con el tiempo y causar filtraciones en el adaptador del tubo.
Instalación Herramientas requeridas Lentes de seguridad Guantes Linterna Llave ajustable Alicate pelacable Pinza Alicate de corte Cinta métrica Lápiz Destornillador Phillips Destornillador plano Cortatubos Cúter Fresa para escariar Nivel Torx t20 Llave en forma de L para cabezas hexagonales Instalación Taladro eléctrico 8 Español DW8000R_DD68-00210A-00_MES.
NOTA Instalación nueva Si la instalación del lavavajillas es nueva, la mayor parte del trabajo debe realizarse antes de colocar el lavavajillas en su lugar. Reemplazo Si el lavavajillas reemplazara a un lavavajillas anterior, debe verificar que las conexiones existentes sean compatibles con el nuevo lavavajillas. Reemplace las conexiones existentes si fuera necesario.
Instalación Si se trata de una instalación nueva, siga estos pasos: 1. Utilizando una fresa para escariar de 21/2 pulgadas, realice una perforación en la pared del gabinete que soporta el fregadero como se detalla en la Figura 1-1 a continuación. 2. Si la base dentro del gabinete del fregadero se eleva sobre el piso de la cocina y es más alta que las conexiones en la lavavajillas, debe hacerse un agujero en la base dentro del gabinete y en el lateral del gabinete como se detalla en la Figura 1-2.
Dimensiones del producto Vista frontal Serie DW80R7060 Serie DW80R7061 237/8" (605 mm) 237/8" (605 mm) 33⅞-35" (860-890 mm) 33⅞-35" (860-890 mm) Caja de conexiones Caja de conexiones Vista lateral Instalación Serie DW80R7060 Serie DW80R7061 27 /16" (693 mm) 5 21/2" (60 mm) 53/4" (140 mm) 41/5" (107 mm) 21/2" (60 mm) 23/4" (70 mm) 201/2" (520 mm) 25" (636 mm) 201/2" (520 mm) 25" (636 mm) Acomode el conducto, el cable de alimentación y la manguera de desagüe en el espacio detrás de la lavava
Instalación Dimensiones del gabinete NOTA 24" (610 mm) mínimo 34⅛-35⅓" (867-897 mm) 24" (610 mm) mínimo Esta lavavajillas está diseñada para colocarse entre los lados y encima de un gabinete en una cocina residencial estándar. El gabinete para la instalación debe estar limpio y libre de obstrucciones. El gabinete debe tener por lo menos 24 pulgadas de ancho, 24 pulgadas de profundidad y 341/8 pulgadas de altura.
PASO 3 Verifique los requisitos para el suministro de agua y precauciones • • La presión del conducto de agua caliente debe estar entre 20 y 120 psi (140 y 830 kPa). Ajuste el calentador de agua para obtener una temperatura de agua entre 120 °F (49 °C) y 149 °F (65 °C). - - La lavavajillas debe estar conectada al suministro de agua caliente entre 120 °F (49 °C) y 149 °F (65 °C). Este rango de temperatura ofrece un mejor resultado en el lavado y un ciclo más corto.
Instalación PASO 4 Verifique los requisitos eléctricos y advertencias Los requisitos eléctricos para la lavavajillas son los siguientes: • • • En los Estados Unidos, instalar de conformidad con el Código Eléctrico Nacional/códigos estatales y municipales y/o códigos locales. En Canadá, instalar de conformidad con el Código Eléctrico Canadiense C22.1-última edición/códigos provinciales y municipales y/o códigos locales. Para conexiones directas de cable.
PASO 5 Desempacar e inspeccionar el lavavajillas Desempaque la lavavajillas en una zona libre de obstrucciones ya sea alrededor de la caja como en la parte superior. Recomendamos que conserve todos los materiales del empaque hasta que la lavavajillas esté completamente instalada y en funcionamiento para asegurarse de que haya retirado todas las piezas del producto de la caja antes de desecharla. Desempaque 1. Ubique el lado derecho de la caja con las flechas superiores señalando hacia arriba. 2.
Instalación Inspección Mecánica 1. Verifique el montaje de la base de plástico para asegurarse que esté intacto. 2. Verifique los soportes de la lavavajillas para asegurarse de que estén en su lugar y que puedan ajustarse con el fin de nivelar y asegurar la lavavajillas. 3. Verifique todas las piezas visibles en la parte inferior de la lavavajillas para asegurar que estén intactas y seguras. 4.
PASO 6 Preparación del lavavajillas 1. Una el autoadhesivo protector (A). - Para evitar daños, coloque el autoadhesivo protector en la parte inferior de la encimera como se muestra en la imagen. NOTA • • Antes de aplicar el autoadhesivo protector, limpie la encimera como se muestra en la imagen. Tenga en cuenta que el autoadhesivo protector mide 26 pulgadas (660 mm) de largo.
Instalación 3. Use el conector de tuerca provisto para conectar la manguera de agua al lavavajillas. Siga estos pasos: 01 02 03 A B E C D F 01 Desconecte el adaptador de 90° (A) de la manguera (B). 02 Retire el sello (C) y la tuerca (D) del adaptador de 90°. 03 En el conector de tuerca provisto, separe el sello (E) y la tuerca (F) y luego ensámblelos en el adaptador de 90° como se ilustra en la figura. Debe insertar el lado más pequeño del sello. 4.
Figura 4 A A A’ A’ C B Caja de conexiones Alivio de tensión Adaptador de 90° PRECAUCIÓN No ajuste demasiado el adaptador de 90°. (Menos de 280 lb·en (31.6 N·m)) Instalación Si lo hiciera, podría dañar la válvula de entrada de agua y ocasionar una pérdida de agua. Español 19 DW8000R_DD68-00210A-00_MES.
Instalación PASO 7 Colocación del lavavajillas y conexión del conducto del suministro de agua caliente 1. Regule las tres patas niveladoras en la parte inferior de la lavavajillas después de medir la altura de la abertura del gabinete desde abajo de la encimera hasta el piso. (Ver el PASO 8, Nivelación de la lavavajillas.) 2. Ubique el conducto del agua caliente y el cable de alimentación. 3.
Figura 5 Burlete lateral Burlete lateral 1 in Caja de conexiones Manguera de desagüe Conducto de suministro de agua caliente Cable de alimentación Válvula de entrada Gancho incorporado Conducto de suministro de agua caliente 3 Codo ( /4” (9.5 mm)) Instalación PRECAUCIÓN No ajuste demasiado el adaptador de 90°. Si lo hiciera, podría dañar la válvula de entrada de agua y ocasionar una pérdida de agua. Asegúrese de que la lavavajillas esté ubicada en el centro.
Instalación PASO 8 Nivelación del lavavajillas 1. Abra la puerta y coloque el nivel contra la parte superior de la cuba desde adentro y verifique si la lavavajillas está nivelada. Si no lo está, gire las patas niveladoras en la parte inferior delantera de la lavavajillas hasta que quede nivelada. Vea la primera nota debajo de las instrucciones sobre el ajuste de la altura de las patas delanteras. 2.
NOTA • • Si gira las patas niveladoras hacia la izquierda (en el sentido de las agujas del reloj), estas se aflojan y la parte delantera del lavavajillas se levanta. Si las gira hacia la derecha (en el sentido contrario al de las agujas del reloj), se ajustan y la parte delantera del lavavajillas baja. Puede regular las patas niveladoras un máximo de 16/32" No obstante, no es recomendable ajustarlas a esta altura máxima.
Instalación PASO 9 Asegurar la lavavajillas La lavavajillas debe asegurarse a la encimera o a las paredes laterales para mayor estabilidad y seguridad. A la encimera Si la encimera está hecha de madera de un material que no se daña por la perforación, siga las siguientes instrucciones. 1. Coloque una toalla grande en la parte inferior de la lavavajillas (que cubra el filtro) para evitar que caigan restos de madera o un tornillo dentro del sumidero del sumidero. 2.
Hacia los laterales Si la encimera está hecha de granito, mármol o cualquier otro material que no se daña por la perforación, siga las siguientes instrucciones. 1. Coloque una toalla grande en la parte inferior de la lavavajillas (que cubra el filtro) para evitar que caigan restos de madera o un tornillo dentro del sumidero del sumidero. 2. Inserte las ménsulas que se proveen en los orificios de la parte lateral delantera de la lavavajillas.
Instalación Correcto A Incorrecto B 22" (560 mm) A B 22" (560 mm) Instalación La distancia entre las tapas no debe superar las 22" (560 mm) PRECAUCIÓN Asegúrese de que la cuba no se deforme a causa de la presión de los tornillos. Si la cuba se deforma, desajuste los tornillos levemente. Reemplace las tapas plásticas. Use la regla de papel para medir la distancia especificada en A y B. 26 Español DW8000R_DD68-00210A-00_MES.
PASO 10 Ajuste 1. Verifique las piezas del fregadero a las cuales se conectará la manguera de desagüe. 2. Hay muchas maneras de insertar la manguera de desagüe en el conector de la manguera de desagüe del fregadero, como se muestra en las siguientes figuras. Debe conectar la salida del desagüe conforme a las reglamentaciones de instalación de tuberías de agua de su región. Figura 8 Caso 1.
Instalación 4. Deslice una abrazadera de manguera en el extremo de la manguera de desagüe. Conecte la manguera de desagüe al conector del fregadero, deslice la abrazadera de la manguera hacia el extremo final de la manguera, y luego ajuste la abrazadera de la manguera. NOTA Debe utilizar una abrazadera de manguera. Si no lo hace, es posible que haya pérdidas de agua. 5.
Figura 9 1 pulgada (25 mm) /8 pulgada (16 mm) 5 /8 pulgada (22 mm) 7 Si es necesario, corte por la línea punteada de la manguera de desagüe para que se adapte al tamaño. Figura 10 Fregadero Mín. 30 pulgadas (762 mm) Manguera de desagüe Instalación Mín. 20 pulgada (508 mm) Lavavajillas Para evitar el flujo de retorno en los modelos sin espacio de aire, asegure la manguera de desagüe en la pared lateral del gabinete de la cocina mediante sujetacables o con otras monturas.
Instalación PASO 11 Conexiones del cableado 1. Antes de conectar el cable de alimentación a la lavavajillas, asegúrese de desactivar el disyuntor. 2. En la caja de conexiones que se encuentra ubicada en la parte delantera derecha inferior de la lavavajillas, busque los tres cables de alimentación de la lavavajillas inclusive la conexión a tierra. 3. Pase el cable de alimentación al alivio de tensión, y luego dentro de la caja de conexiones (Figura 11). 4.
Figura 12 ADVERTENCIA • Riesgo de descarga eléctrica Para evitar descargas eléctricas, no manipule un circuito energizado. Si lo hiciera, podría causar lesiones graves o incluso la muerte. Solo los técnicos de servicio calificados pueden realizar conexiones eléctricas. No intente manipular el circuito de suministro eléctrico de la lavavajillas hasta que no esté seguro de que está desenergizado.
Instalación PASO 12 Finalización de la instalación 1. Abra la puerta y quite todas las piezas innecesarias, goma espuma y empaque de papel. 2. Active el disyuntor desactivado antes de comenzar la instalación. 3. Abra la válvula del suministro de agua para suministrar agua a la lavavajillas. 4. Encienda la lavavajillas y luego seleccione y ejecute un ciclo. PRECAUCIÓN Verifique las filtraciones de agua en ambos extremos del conducto de agua y en el conector de la manguera de desagüe. 5.
d. El ciclo de Instalación inteligente se ejecutará durante 7 minutos aproximadamente. e. Luego, la puerta de la lavavajillas se abrirá y se mostrará el número "5” durante 1 minuto aproximadamente. f. Se mostrará "Ot” luego de que se ejecute exitosamente el ciclo de Instalación inteligente. 10. Si el código de información “LC” continúa apareciendo en el panel, comuníquese con un centro de servicio técnico local. 11. Finalmente, coloque la placa de protección en la parte inferior de la lavavajillas.
Especificaciones Suministro eléctrico Presión de agua Dimensiones 120 V, 15 A, 60 Hz CA 20~120 psi (140 ~ 830 kPa) 237/8 x 25 x 337/8 pulgadas. (Ancho × Profundidad × Altura) Temperatura mínima del agua en la entrada (605 x 636 x 860 mm) 120 °F (49 °C) NOTA Las especificaciones están sujetas a cambios sin previo aviso a los efectos de las mejoras de calidad. La apariencia real de la lavavajillas puede diferir de las ilustraciones de este manual. Especificacione 34 Español DW8000R_DD68-00210A-00_MES.
Notas DW8000R_DD68-00210A-00_MES.
DD68-00210A-00 DW8000R_DD68-00210A-00_MES.