3D-B1311-EU.indb 1 SCC-B1311(P) SCC-B1011P DIGITAL COLOR CAMERA operating instructions imagine the possibilities Thank you for purchasing this Samsung product. To receive more complete service, please register your product at www.samsung.
safety precautions CAUTION RISK OF ELECTRIC SHOCK. DO NOT OPEN CAUTION: TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK)NO USER-SERVICEABLE PARTS INSIDEREFER SERVICING TO QUALIFIED SERVICE PERSONNEL This symbol indicates that dangerous voltage consisting a risk of electric shock is present within this unit. This symbol indicates that there are important operating and maintenance instructions in the literature accompanying this unit.
re. ury. ENG n 6. Do not place conductive objects (e.g. screwdrivers, coins, metal things, etc.) or containers filled with water on top of the camera. Doing so may cause personal injury due to fire, electric shock, or falling objects. 7. Do not install the unit in humid, dusty, or sooty locations. Doing so may cause fire or electric shock. 8. If any unusual smells or smoke come from the unit, stop using the product. In such case, immediately disconnect the power source and contact the service center.
important safety instructions e 1. Read these instructions. 2. Keep these instructions. 3. Heed all warnings. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean only with dry cloth. 7. Do not block any ventilation openings. Install in accordance with the manufacturer’s instructions. 8. Do not install near any heat sources such as radiators, heat registers, or other apparatus (including amplifiers) that produce heat. 9.
ENG external cctv camera installation 1 Installing the lightening conductor and grounding system. Separate grounding system. 2 Installing the camera and grounding system. Grounding wire to a good earth ground (100Ω or less. ground resistance.) (Class 3) 3 The class 3. (Camera grounding) Separate grounding system from the lightening conductor. ns. ➧ e e ith pply e d. The surface Treating the raw materials that reduce the ground resistance around the ground rods. Ground resistance: 100Ω or less.
c 1. Installing a lightening conductor a) Protection area b) Protected angle (Depending on the height of the lightening conductor) 2. Camera grounding No Distinguished by Standard Note 1 Grounding method The class 3 CCTV product 2 Thickness of the Grounding wire 1.6mm2 3 Ground resistance 100Ω The purpose of the camera grounding Installing the lightening conductor and grounding the camera chassis prevent the CCTV camera from the lightning strikes.
g 3D-B1311-EU.
overview fe It is a high-resolution box camera that has implemented the horizontal resolution of 540 lines by taking advantage of the Digital Signal Processing and OLPF technologies. • I n mechanical fluorescent lightning conditions, you can experience so-called “color rolling” if you have installed the manual iris lens on the camera and positioned the function switch from ELC to ON. In this case, connect the camera to the power source (AC) and position the L/L switch on the rear panel to EXT.
ENG features the XT. e High Color Sensitivity The camera adopts the latest 1/3” super-HAD IT CCD to get the benefit of high color sensitivity. Resolution Introduces Full Digital Image Processing from the digital signal technology to implement a high-resolution image. Excellent Back Light Compensation This will guarantee a sharp image by compensating for the back light even if the sunlight or bright lightening reflects against the subject.
installation Parts & Description In this chapter, we will provide you with general instructions for product installation and preferred places as well as considerations before installation. Now, let’s install the camera and connect necessary cables.) 3 Auto Iris Lens Connector Mount Adaptor Holes 4 Package Flange Back Adjustable Ring 2 You must check that all the components and accessories listed below are included in the product package.
s, h Auto Iris Lens Connector Provides power source and control/ DC signal with iris lens that are required to control the iris of the lens 4 Flange Back Adjustable Ring Used to adjust the back focus of the camera. 5 Auto Iris Lens Control Cable Transfers the control signal from the camera to the iris lens. Connect the auto iris lens connector Remove the sheath round the iris control cable and connect it to each of the auto iris lens connector as described below.
Install the lens Co Lens without zooming feature Loosen the single screw on the adjustable ring of the flange back by turning it anti-clockwise and turn the ring in the “C” direction (anti-clockwise) to the end. Otherwise, it can cause damage to the internal image sensor or the lens when you install the lens on the camera. C direction 1. C apture a sharp subject (with a grid pattern) more than 10m apart and adjust the focus ring to the infinity ( ∞ ). 2.
Connect the cables and check the operation AC24V/DC12V (SCC-B1311, B1311P) ENG n . t e so and ou s M e VIDEO IN Terminal on the rear of moniter BNC Cable VIDEO OUT Terminal AC220V ~ 240V (SCC-B1011P) 1. Connect one end of the BNC cable to the VIDEO OUT port of the monitor. 2. Connect the other end of the BNC cable to the VIDEO In port. 3. C onnect the camera to the power adaptor.
AC24V/DC12V (SCC-B1311, B1311P) 5 1 Power Port Port that is connected to the power (adaptor) cable. - For SCC-B1311, B1311P Connects to AC 24V or DC 12V. - For SCC-B1011P Connects to AC220V ~ 240V. 2 Power Indication LED If properly supplied with power, the LED turns on. 3 Vertical Synchronization Phasing Switch (Left) Used to adjust the vertical synchronization phasing. If pressed, the vertical synchronization moves to the left. AC220V ~ 240V (SCC-B1011P) 6 1. ELC 3. FL 5 2. BLC 4.
5 g. he 1. ELC 2. BLC 3. FL(Flickerless) 4. AWB SW1(ELC) Use this for the manual iris lens. If set to ON, the electronic shutter speed varies between 1/60 and 1/120,000 second to keep the screen brightness proper. However, you must position this switch to OFF if you are using the auto iris lens (DC control type). Because, in this mode, the camera can show the color rolling effect when operating under the mechanical fluorescent lightning. If this happens, apply the AC power and set the L/L to "EXT".
6 FUNCTION SWITCH-2 7 제품사양sp DC IRIS Level Bar SC Ite Pr Br Sy Im Used to adjust the iris level of this level bar using a screwdriver. If multiple cameras are connected to such as a sequential switcher in auto switch mode, the camera in the internal sync mode occurs a skip every time it moves to other scene. However, this can be solved by positioning the L/L switch to EXT and using the level bar to adjust the vertical sync phasing. - Anti-clockwise: Decreases the luminance level.
SCC-B1311 Item Description Item Description Product Type Surveillance Camera FL(FLICKERLESS) OFF/ON Broadcasting System NTSC STANDARD SYSTEM Lens Manual/Auto Iris DC Lens Imaging Device 1/3”IT, S-HAD-CCD Number of Effective Pixels 768(H) x 494(V) Scanning 525 Line, 2:1 interlace Lens Mount C, CS Lens Adaptable AWB(Auto White Balance) ON : ATW OFF : AWC BLC(Back Light Compensation) ON/OFF AGC AUTO Line Frequency INTERNAL : 15,734Hz(H) 59.
SCC-B1311P, B1011P Item Description Item Description Product Type Surveillance Camera Lens Mount C, CS Lens Adaptable Broadcasting System PAL STANDARD SYSTEM AWB(Auto White ON : ATW Balance) OFF : AWC Imaging Device 1/3”IT, S-HAD-CCD Number of Effective Pixels BLC(Back Light Compensation) ON/OFF 752(H) x 582(V) AGC AUTO Scanning 625 Line, 2:1 interlace Line Frequency INTERNAL : 15,625Hz(H) 50 Hz(V) LINE LOCK : 15,625Hz(H) 50 Hz(V) Signal Out COMPOSITE VIDEO OUT 1V p_p 75 Ω / BNC Syn
s s 3D-B1311-EU.indb 13 Correct Disposal of This Product (Waste Electrical & Electronic Equipment) (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
Memo 3D-B1311-EU.