DAY & NIGHT COLOR CCD CAMERA INSTRUCTION MANUAL SDN- 520N/P SDN- 510N/P om tv.c w un ms .sa ww gcc SALES NETWORK SAMSUNG TECHWIN CO., LTD Optics & Digital Imaging Division 145 -3, Sangdaewon 1-Dong, Jungwon-Gu, Sungnam, Kyungki-Do, Korea 462-121 TEL :82 -31-740 - 8137~41 FAX : 82 -31-740 - 8145 SAMSUNG OPTO-ELECTRONICS AMERICA, INC. Closed Circuit Division 40 Seaview Drive, Secaucus N.J 07094, U.S.A. TEL : (201) 902-0347 FAX : (201) 902-9342 P/ NO.
CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK), NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. The lightning flash with an arrowhead symbol, within an equilateral triangle is intended to alert the user to the presence of uninsulated "dangerous voltage" within the product's enclosure that may be of sufficient magnitude to constitute a risk of electric shock to persons.
Electronic Iris The electronic iris shutter is automatically controlled at the speed of 1/60~1/10,000sec(NTSC Models), / 1/50~1/10,000sec(PAL Models). Powerful Backlight Compensation The backlight compensation technology allows the camera to find the best picture conditions in any environment and automatically gives the necessary light level compensation, so that you can always obtain the clearest picture, finest detail and perfect light contrast.
Do not drop the camera or subject them to physical shocks. It can cause malfunctions to occur. Do not touch the front lens of the camera. Do not expose the camera to rain or spill beverage on it. If it gets wet, wipe it dry immediately. Liquids can contain minerals that corrode the electronic components. Never keep the camera face to strong light directly. It can damage the CCD.
GETTING TO KNOW YOUR CAMERA Bottom Front C Mount Adapter. Attach the C-Mount Adapter when using the C-Mount Lens. Tripod Mounting Bracket Screw Hole. Used to fix the Tripod mounting bracket on the top of the camera. Tripod Mounting Hole Used to install the camera on an optional tripod. The tripod must be equipped with the screw specified as shown below. 1/4"-20 UNC (20 THREAD) L:4.5mm±0.2mm (ISO standard), or 0.197" (ASA standard) L om tv.c gcc sun am w.s ww om tv.c gcc sun am w.
GETTING TO KNOW YOUR CAMERA Back GETTING TO KNOW YOUR CAMERA Accessories REMOTE Jack Used to connect a remote plug. This jack also provides the motion detect signal. Auto Iris Lens Plug DC/VIDEO Selection Switch Remote Plug Used to choose DC or VIDEO according to the type of your auto iris lens. Video Out Jack Used to connect an external video monitor in jack. L-Wrench Menu Setup Buttons SET Button Used to access menu mode. Also used to confirm the setting.
CONNECTION 3. Remove the cover from the iris lens plug supplied, and solder the lens cable to the plug as shown below. Lens The lens is not supplied with this camera. Purchase a lens suitable for your environment. This camera accepts the auto iris lens and both C- and CS-mount lens. • Video type : No. 1 Pin --- Red (Power source) No. 2 Pin --- N.C No. 3 Pin --- White (Video signal) No. 4 Pin --- Black (GND) • DC type : No. 1 Pin --- Damping No. 2 Pin --- Damping + No. 3 Pin --- Drive + No.
Mounting a C-mount lens 1. Attach the C Mount lens adapter by turning clockwise. Mounting a CS-mount lens After removing the protecting cap, attach the lens into the camera by turning clockwise. 2. Attach the lens to the camera by turning clockwise. Use the lens under the specification as shown. Otherwise the lens can NOTE damage the camera or abnormal fixing may result.
Connecting to Monitor Connect the VIDEO Out jack to the monitor VIDEO In jack. • As the connecting method varies with the instruments, refer to the manual supplied with the instrument. • If necessary, you can connect the monitor to the REMOTE jack on the back of your camera. For details, see page 39. • Only connect the cable when the power is turned off. • Set the 75Ω/Hi-Z selection switch as shown below if you have an intermediate device.
CONFIGURATION OF MENU Setup Menu Gain Control (see page 34) Camera ID (see page 23) • ON : Activate. You can enter up to 14 alphanumeric characters and select the ID position. • AGC (Auto Gain Control) : Activates AGC feature. • OFF : Deactivate AGC feature. White Balance Control (see page 35) • OFF : Deactivate • ATW (Auto Tracing White balance) : Automatically controls white balance. • AWC (Auto White balance Control) : Automatically controls white balance.
SETUP MENU 2. Select the desired feature using the UP or DOWN button. Use the five Setup Menu buttons on the rear of the camera. Each time you press the UP or DOWN button, the arrow indicator moves up or down. Move the arrow indicator to the desired feature item. Setup Select the function using the UP or DOWN button. UP button LEFT button SET button RIGHT button DOWN button Camera ID Backlight Motion Detect. Lens Shutter Gain White Balance Color Sync.
5. Select the position at which the camera ID will be located on the screen. 3. Press SET button. The ID generation screen appears. Move the cursor to 'Pos' and press SET button. The camera ID is displayed on the top left of the monitor screen. (Default position) 4. The alphanumeric letters are displayed. You can enter up to 14 characters. Move the cursor to the desired character by using the 4directional buttons. The selected character blinks and appears in the bottom of the screen.
SETUP MENU SETUP MENU Backlight Motion Detection The Wide Dynamic Range and Super BLC technology in your camera provides intelligent light level control to overcome the severe Backlight conditions. Your camera transmits an alert signal when it detects motion of an object on the screen. If you connect the camera to an external alarm, you can pay attention to the screen when the alarm sounds. This feature is useful when you have to monitor several screens simultaneously. 1.
SETUP MENU SETUP MENU How to Assign the Zone 4. Specify the zone area. You can point to the top, bottom, left, and right base lines by setting a proper value from 0 to 15 with an increment of 1. If you assign a zone, an alert signal occurs when the camera detects motion of objects in that zone. Top base line Ex. Zone Top 2 Bottom 12 Left 0 Right 7 Ex. Full screen Right base line Left base line 5. Adjust Sensitivity.
6. When completed, move the arrow indicator to 'End' and press the SET button. Lens Selection You can set the type of the lens, and control the brightness of the screen. Tips on Using the Motion Detection Feature • After selecting zone and sensitivity, perform a test operation to make sure it works properly. • If the lighting flickers, the motion detection feature might not work properly. 1. Press the SET button to display the setup menu and move the arrow indicator to 'Lens' using the UP or DOWN button.
SETUP MENU SETUP MENU 3. If you choose “DC”, you can adjust the brightness. After pressing the SET button, adjust the brightness of the monitor screen using the LEFT or RIGHT button. The screen becomes darker when the value is decreased and brighter when the value is increased. You can adjust the brightness from 0 to 99. Notes 3. If you choose 'Manual', select the optimal shutter speed. You can select speed from '1/60' to '1/10,000' sec (NTSC Models), / '1/50' to '1/10,000' sec (PAL Models).
Gain Control White Balance Control 1. Press the SET button to display the setup menu and move the arrow indicator to 'Gain' using the UP or DOWN button. Your camera provides 3 white balance control modes. You can select the most suitable one. You can adjust the white balance. 2. Select 'AGC' or 'OFF' using the LEFT or RIGHT button. 1. Press the SET button to display the setup menu and move the arrow indicator to 'White Balance' using the UP or DOWN button.
SETUP MENU SETUP MENU Color ( Day & Night) Synchronization Mode Your camera provides automatic mode changeover by sensing day or night conditions. It changes to Color mode in day conditions for optimal color and to BW mode in night conditions for clear identification. 1. Press the SET button to display the setup menu and move the arrow indicator to 'Color' using the UP or DOWN button. 2. Select a mode using the LEFT or RIGHT button.
SETUP MENU The phase is preset to 225 degrees at the factory. You can readjust it from 0 to 270 degrees. Line Lock Phase If you connect a remote plug to the REMOTE jack on the rear of the camera as shown below, you can access the menu setup mode from a remote place. 225 Press SET to Return Notes NOTE is 50Hz, you can not use linelock When the power frequency mode(NTSC Models). When the power frequency is 60Hz, you can not use the linelock mode(PAL Models). ’Sync.
TROUBLESHOOTING If you have trouble operating your camera, refer to the following table. If the guidelines do not enable you to solve the problem, contact an authorized technician. Problem Solution Nothing appears on • Check that the power cord and line connection between the camera and monitor are fixed properly. the screen. • Check that the DC/VIDEO selection switch on the rear of the camera is set to a proper position according to the type of your auto iris lens. The image on the screen is dark.
DECLARATION OF CONFORMITY Item Power Source Image Pick-Up Device Scanning System Picture elements Effective picture elements Resolution Video Output Backlight Compensation Color RS-232C Communication O.S.D Iris Mode Electronic Shutter White Balance Lens Mount Min.