The product color and shape may vary depending on the model.
To avoid injuries or damage to property, please read the following precautions carefully and use the product accordingly. Failure to follow the instructions marked with this symbol may cause personal injury or even fatality. Failure to follow the instructions marked with this symbol may cause personal injury or damage to the product or property. | Power Related | Installation Related | Cleaning and Use Related | [The images here are for reference only, and are not applicable in all cases (or countries).
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. z There is a danger of electric shock or fire. Always unplug the unit by holding the power plug. Pulling the power cable may damage the inside of it. z There is a danger of fire. Unplug the power plug before cleaning the product. z There is a danger of electric shock or fire.
Do not install on an unstable location, or on a stand smaller than the product. z If the product falls it may harm children. Install on a flat and stable location as the front part is heavy. In case of thunder/lightning, disconnect the power cord from the wall outlet. z There is a danger of electric shock or fire. Make sure the product's vents are not blocked by a table cloth or curtain. z An increase in the internal temperature may cause a fire. Place the product on the ground carefully.
z This may cause electric shock or fire. If water or an alien substance enters the product, turn the product off, disconnect the power cord from a wall outlet and contact a Service Center. Do not disassemble, or attempt to fix or modify the product. z When the product requires repairs, contact a Service Center. Do not use or keep the product near flammable sprays or other such substances. z There is a danger of fire or explosion.
When cleaning the product, disconnect the power cord and wipe the product using a soft dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. When not using the product for an extended period of time, disconnect the power plug. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
(Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household waste at the end of its working life. To prevent possible harm to the environment or damage to health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources.
| Product Features | Product Views | Remote Control | Product Specifications | Optical engine with advanced DLP technology - Full 1920x1080 HD panel. - 6 segment color wheel to implement optimal colors. - 300W Lamp designed to improve luminance Vivid colors - Quality picture tuning focused on improving color - this unit aims at realizing color coordinates that meet broadcasting standards on video production.
1. Indicators 7. Zoom Knob - TEMP (Red LED) Used to enlarge or reduce image size. - LAMP (Blue LED) 8. POWER( - STAND BY (Blue LED) ※ Refer to the LED Indications. ) Button Used to turn the projector on or off. 2. Focus Ring 9. SOURCE Button Used for Focus Adjustment. Used to select input signals from the external sources. 3. Lens 10.MENU Button 4. Lens Position Moving Dial Use this button to enter or exit a menu or to You can adjust screen images up and down move forward in a menu.
Remote Control/ 2 Batteries Power Cable Cleaning Cloth (Not available in all locations) LED Indications :Light is On STAND BY :Light is Blinking LAMP :Light is Off TEMP Information If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. The projector is in normal operating condition. This state appears when the projector is preparing an operation after the POWER button on the projector or the remote control has been pressed.
When temperature inside Action 3 of the projector becomes too high. Action 4 When the DDP IC or color wheel fails to operate. Adjust the installation state of your projector by referring to the Installation Precautions section listed above. Cool down your projector sufficiently and then operate it again. If the same problem occurs continually, contact your product distributor or service center. Disconnect and reconnect the power cord and start the projector again.
| Product Features | Product Views | Remote Control | Product Specifications | 1. ON ( 2. COMP1 Button 3. VIDEO Button 4. S-VIDEO Button 5. PC Button 6. MENU Button 7. Move (▲ ▼ ◀ ▶)/ENTER Button 8. INFO Button 9. P.SIZE Button ) Button 10. STILL Button 11. P.MODE Button 12. OFF ( 13. ) Button LIGHT ( ) Button 14. HDMI1 Button 15. HDMI2 Button 16. COMP2 Button 17. RETURN Button 18. EXIT Button 19. D.BLACK Button 20. USER Button 21. INSTALL Button 1.
Used to adjust the size of picture screen. 10. STILL Used to see still images. 11. P.MODE Used to select Picture Mode. 12. OFF ( ) Used to turn off the projector. 13. LIGHT ( ) Used to operate remote control in dark room. 14. HDMI1 Used to switch to HDMI 1 Mode. 15. HDMI2 Used to switch to HDMI 2 Mode. 16. COMP2 Used to switch to COMPONENT 2 Mode. 17. RETURN Returns to the previous menu. 18. EXIT Used to make Menu Screen disappear. 19. D.
Maximum Pixel Clock 162 MHz Diagonal screen size 1016 mm ~ 7620 mm (16:9, Diagonal) Projection Range 1.5 m ~ 14 m Power Less than 410 W Consumption Power Voltage 110/220 Vac +/-10 %, 50/60 Hz +/-3 Hz Noise Theater : 24dB, Bright : 30dB 431.3 mm(W) x 468.5 mm(D) x 198.8 mm(H) Dimensions 17.0 inches(W) x 18.4 inches(D) x 7.8 inches(H) Weight 9.8 Kg / 21.
1280x720 1280x768 1664x748 44.8 N 59.9 P 74.5 Sep. 1696x750 52.5 N 70.0 N 89.0 Sep. 1696x751 54.1 N 72.0 N 91.7 Sep. 1696x755 56.5 N 74.0 P 95.8 Sep. 1664x798 47.8 N 59.9 P 79.5 Sep. 1696x805 60.3 N 74.9 P 102.3 Sep. Sep. 1712x809 68.6 N 84.8 P 117.5 1800x1000 60.0 P 60.0 P 108.0 Sep. 1728x999 69.9 N 70.0 P 120.8 Sep. 1728x1001 72.1 N 72.0 N 124.5 Sep. 1728x1005 75.2 N 74.9 P 130.0 Sep. 1728x1011 85.9 P 85.0 P 148.5 Sep.
O : Size & Overscan can be configured, x : Size & Overscan cannot be configured, △: Size can be configured Source Input Type HD HDMI SD HD Component SD Video & SD S- Video HD PC SD PC Picture Size Mode 16:9 Zoom1 Zoom2 4:3 Wide fit Anamorphic 1080p O O O O O O 1080i O O O O O O 720p O O O O O O 576p O O O O x O 480p O O O O x O 576i O O O O x O 480i O O O O x O 1080p O O O O O O 1080i O O O O O O 720p O O O O O O 576p
HD SD HDMI DVI HD Component SD Video & S- Video SD HD PC SD PC 1080p x x O O O O 1080i x x O O O O 720p x x O O O O 576p x x O O x O 640 x 480p x x O O x O 720 x 480p x x O O x O 576i x x O O x O 480i x x O O x O 1280 x 1024/60 x x x x x x 1024 x 768/60 x x x x x x 800 x 600/60 x x x x x x 720 x 400/70 x x x x x x 640 x 350/70 x x x x x x 1080p O O O O O O 1080i O O O O O O 720p O O O O O
| Basic Settings | Connecting the Power | Connecting to video equipment | Installing the Projector Install the projector so that the beam from the projector is perpendicular to the screen. Place the projector so that the lens is at the center of the screen. If the screen is not vertically installed, the picture on the screen may not be a rectangle. Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be displayed clearly.
Zoom Knob Focus Ring You can adjust the size of image within zoom range by manipulating the Zoom Knob. Focus the picture on the screen using the Focus Ring. If your product is installed at a location out of the specified projection distance (refer to Screen Size and Projection Distance), the focus cannot be adjusted correctly. Leveling with Adjustable Feet For level placing of the projector, adjust the Adjustable Feet of the projector. You may adjust the level of the projector up to 3 degrees.
Screen size Horizental (M:inch) (X:mm) 40 Vertical(Y:mm) Min(Z:mm) Max(Z:mm) Offset (Y':mm) 886 498 1983.6 1523.1 50 50 1107 623 2479.5 1903.9 62 60 1328 747 2975.3 2284.6 75 70 1550 872 3471.2 2665.4 87 80 1771 996 3967.1 3046.2 100 90 1992 1121 4463 3427 112 100 2214 1245 4958.9 3807.7 125 110 2435 1370 5454.8 4188.5 137 120 2657 1494 5950.7 4569.3 149 130 2878 1619 6446.6 4950.1 162 140 3099 1743 6942.5 5330.
2. Click on [Settings] tab and set the by referring to described in the display mode table supported by this projector. You do not have to change setup. 3. Press the [Advanced] button. Another property window will appear. 4. Click on [Monitor] tab and set the by referring to described in the Supported Resolution/Size Modes table. Set up both the vertical and horizontal frequency instead of .
projector. If not, there may be signal problems. | Basic Settings | Connecting the Power | Connecting to video equipment | 1. Rear of Projector Plug the power cord into the power terminal on the rear side of the projector. When used outside of the U.S., HAR cord with fittings of an approved agency may be used.
- Connecting using a HDMI/DVI cable Connect the [HDMI 1/DVI IN] terminal on the back of the projector and the DVI output terminal of the DVD player/Cable/Satellite box using a HDMI/DVI cable. - Connecting using a HDMI cable Connect the [HDMI 1/DVI IN] or [HDMI IN 2] terminal on the back of the projector and the HDMI output terminal of the DVD player/Cable/Satellite box using a HDMI cable. When the connection is finished, connect the power of your projector and DVD player/Cable/Satellite box.
Connect the [COMPONENT IN 1 (Y/PB/ PR)] or [COMPONENT IN 2 (Y/PB/ PR)] input port at the back of the projector to the Component port at the back of the DVD player/Cable/Satellite box with the Component cable. When the connection is finished, connect the power of your projector and DVD player/Cable/Satellite box. Using the Projector Turn on the projector and press the [COMP1] button to select . Press the [COMP2] button to select if [COMPONENT IN 2] is connected.
Connect [VIDEO IN(yellow)] input port of the projector to the VIDEO (yellow) OUT port of video equipment using the video cable. - If the video equipment has S-VIDEO OUT port, connect it to [S-VIDEO IN] input port of the projector. Using the S-VIDEO connection, provides a higher visual quality. When finishing connecting the devices, connect the power of the projector and the VCR. Using the Projector Turn on the projector and press the [Video] button to select
Connect [PC IN] port on the rear side of the projector to the monitor output port of the PC using a PC video cable. When connections are all completed, connect both power codes of the projector and the PC. This product supports plug and play and therefore, if you use Window XP you do not need to setup the driver on your PC. Using the Projector Turn on the projector and press the [PC] button to select . If PC Mode is not available, check PC video cable is in place.
| Input | Picture | Setup | Option | * Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Source List )/Stop( Play/Stop You can select a device connected to the projector to display. 1) Component 1 5) PC 2) Component 2 6) HDMI 1 3) S-Video 7) HDMI 2 4) Video Edit Name You can edit the names of devices connected to the projector.
* Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Mode )/Stop( Play/Stop Select a screen state which is customized to your projector or change the screen mode as required. 1) Mode - Dynamic Select this if you want the screen quality to be clearer than standard screen quality. - Standard You can comfortably view the projection screen if the surrounding is somewhat Mode bright. - Movie1, Movie2 Select this if your surroundings are dark.
1) Color Temperature 5) R-Offset 2) R-Gain 6) G-Offset 3) G-Gain 7) B-Offset G-Offset B-Offset 4) B-Gain 8) Gamma : An image compensation function that controls the settings according to the video properties. - Film : The best setting for watching a film. Gamma - Video : The best setting for watching a TV program. - Graphic : The best setting when you have a PC connected. 9) DynamicBlack™ : Adjusts the brightness and contrast of the screen by adjusting the tightening thread in the optical system.
1) Off : Shows the picture in the original color. 2) Monochrome : Shows the picture in black and white by filtering out all color signals. 3) Red : Shows the picture in red by filtering out the green and blue color signals. 4) Green : Shows the picture in green by filtering out the red and blue color signals. 5) Blue : Shows the picture in blue by filtering out the red and green color signals.
Adjustment Install Description Play/Stop To tailor the picture to the installation location, you can invert the projected images vertically/horizontally. 1) Front-Floor : Normal Image 2) Front-Ceiling : Horizontal/Vertical Reversed Image 3) Rear-Floor : Horizontally Reversed Image 4) Rear-Ceiling : Vertically Reversed Image Light Setting Used to set the image brightness by adjusting the amount of light generated by the lamp. 1) Bright : Used to enhance the brightness in relatively bright ambient light.
Factory Default Using this function, you can reset various settings to the factory default settings. | Input | Picture | Setup | Option | * Click the Play( Screen )/Stop( Description Adjustment Language You can select the language used for the menu screen. Menu Position You can move Menu Position up/down/left/right. Menu You can set the translucency of menu. Translucency 1) Opaque 2) Low 3) Medium 4) High Menu Display You can set the display time of the menu.
LED Indicator You can enable or disable the operating LED's on the product. 1) Off : This mode disables the operating LED. However, the LED will come on regardless of the LED setting when the power is turned on or off or when the projector is in an abnormal state. 2) On : This mode enables the operating LED so that it can display the current operating state of the projector. Light Effect You can turn the LED indicators on your projector on or off according to your requirements.
| Before Contacting Service Personnel | Installation and Connection Symptoms Troubleshooting No Power. z Check the power cable connections. I want to install my projector on z The ceiling installation support is sold separately. Contact your local product distributor. the ceiling. External Source can not be z Be sure that the connection cable(s) (video) is properly connected to the proper port. If the device is not connected properly, it can not be selected. selected.
adjustment items, such as the Brightness and the Contrast have been changed correctly in the command screen of the Projector menu. Only blue screen appears. z Be sure to properly connect the external devices. Check the connection cables again. Screen appears in black and white or odd color./ screen is too dark or bright. z As mentioned above, check the adjustment items such as the Brightness, Contrast and Color in the menu.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | To clean the exterior and lens of the projector Clean the projector using a soft dry cloth. Do not clean the projector with flammable substances such as benzene, thinners or a wet cloth, as these may cause problems. Do not touch the projector with a nail or any other sharp objects, as this may scratch the surface.
When handling the lamp, avoid touching any part of it except for the handles. If you handle the lamp incorrectly, it may affect the screen quality and shorten its lifetime. LAMP(S) INSIDE THIS PRODUCT CONTAIN MERCURY AND MUST BE RECYCLED OR DISPOSED OF ACCORDING TO LOCAL STATE OR FEDERAL LAWS. For details see lamprecycle. org, eiae.org, or call 1-800-Samsung Lamp Replacement Procedure The lamp is very hot and operates The lamp is located at the left Open the cover by holding down with a high voltage.
Latin America ARGENTINE BRAZIL 0800-333-3733 http://www.samsung.com/ar 0800-124-421 http://www.samsung.com/br 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.samsung.com/cl COLOMBIA 01-8000112112 http://www.samsung.com/co COSTA RICA 0-800-507-7267 http://www.samsung.com/latin ECUADOR 1-800-10-7267 http://www.samsung.com/latin EL SALVADOR 800-6225 http://www.samsung.com/latin GUATEMALA 1-800-299-0013 http://www.samsung.com/latin HONDURAS 800-7919267 http://www.samsung.
SLOVAKIA 0800-SAMSUNG (726-7864) http://www.samsung.com/sk SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com/es SWEDEN 075 - SAMSUNG(726 78 64) http://www.samsung.com/se SWITZERLAND 0848 - SAMSUNG(7267864, CHF 0.08/min) http://www.samsung.com/ch U.K 0845 SAMSUNG (7267864) http://www.samsung.com/uk CIS ESTONIA 800-7267 http://www.samsung.com/ee LATVIA 8000-7267 http://www.samsung.com/lv LITHUANIA 8-800-77777 http://www.samsung.
TURKEY U.A.E 444 77 11 http://www.samsung.com/tr 800-SAMSUNG(726-7864) 8000-4726 http://www.samsung.com/ae | Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | Glossary Analog Broadcast An existing broadcasting signal transmitted by a broadcasting station in accordance with the NTSC standard. ANTENNA IN Port This is the port for connecting a TV antenna using a coaxial cable. It is generally used to watch public broadcast programs.
A DMD panel is an implementation of DLP technology. It consists of microscopic mirrors where each mirror represents a pixel. External Input External Input is connecting video devices such as a VCR, camcorder, DTV receiver, DVD, etc. to the projector as a video source. Gamma Mode Gamma Mode compensates the video signal produced for analog display devices such as a CRT (Cathode Ray Tube) so that the video signal can be clearly displayed on a digital display device.