To avoid injuries or damage to property, please read the following precautions carefully and use the product accordingly. Failure to follow the instructions marked with this symbol may cause personal injury or even fatality. Failure to follow the instructions marked with this symbol may cause personal injury or damage to the product or property. | Power Related | Installation Related | Cleaning and Use Related | [The images here are for reference only, and are not applicable in all cases (or countries).
To disconnect the apparatus from the mains, the plug must be pulled out from the mains socket, therefore the mains plug shall be readily operable. z There is a danger of electric shock or fire. Always unplug the unit by holding the power plug. Pulling the power cable may damage the inside of it. z There is a danger of fire. Unplug the power plug before cleaning the product. z There is a danger of electric shock or fire.
Do not install on an unstable location, or on a stand smaller than the product. z Make sure to keep the product out of the reach of children. The product may fall and cause personal injury. In case of thunder/lightning, disconnect the power cord from the wall outlet. z There is a danger of electric shock or fire. Make sure the product's vents are not blocked by a table cloth or curtain. z An increase in the internal temperature may cause a fire. Place the product on the ground carefully.
z This may cause electric shock or fire. If water or an alien substance enters the product, turn the product off, disconnect the power cord from a wall outlet and contact a Service Center. Do not disassemble, or attempt to fix or modify the product. z When the product requires repairs, contact a Service Center. Do not use or keep the product near flammable sprays or other such substances. z There is a danger of fire or explosion.
When cleaning the product, disconnect the power cord and wipe the product using a soft dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. When not using the product for an extended period of time, disconnect the power plug. z Otherwise, this may cause heat emission from the accumulated dirt or degraded insulation, leading to electric shock or fire.
environment or damage to health from uncontrolled waste disposal, please separate this from other types of waste and recycle it responsibly to promote the sustainable reuse of material resources. Household users should contact either the retailer where they purchased this product, or their local government office, for details of where and how they can take this item for environmentally safe recycling. Business users should contact their supplier and check the terms and conditions of the purchase contract.
| Product Features | Product Views | Remote Control | Product Specifications | Optical engine with advanced DLP technology - 1024 x 768 panel has been adapted. - 4 segment color wheel to implement optimal colors. - 280 W Lamp designed to improve luminance Vivid colors - Quality picture tuning focused on improving color - this unit aims at realizing color coordinates that meet broadcasting standards on video production.
1. Indicators 6. Zoom Knob - STAND BY (Blue LED) Used to enlarge or reduce image size. - LAMP (Blue LED) 7. POWER( - TEMP (Red LED) ※ Refer to the LED Indications. ) Button Used to turn the projector on or off. 2. Focus Ring 8. SOURCE Button Used for Focus Adjustment. Used to select input signals from the external sources. 3. Remote Control Signal Receiver 9. MENU Button 4. Lens Use this button to enter or exit a menu or to move forward in a menu. 5.
Remote Control/ 1 Batteries Power Cable Cleaning Cloth (Not available in all locations) D-Sub Cable Lens cover LED Indications ●:Light is On STAND ◐:Light is Blinking LAMP TEMP ● ○ ○ ● ● ○ ● ◐ ○ ○ ◐ ○ BY ○:Light is Off Information If you press the POWER button on the remote control or projector, the screen appears within 30 seconds. The projector is in normal operating condition.
When the lamp cover protecting the lamp unit is Action 2 not properly closed or the sensor system is not in normal operating Check whether the screws at the bottom side of the projector are fastened correctly. If they are abnormally fastened, contact your product distributor or service center. condition. When temperature inside Action 3 of the projector becomes too high. Action 4 When the color wheel fails to operate.
4. S-VIDEO IN Input port 9. COMPONENT IN Input port 5. Remote Control Signal Receiver 10.POWER Input port | Product Features | Product Views | Remote Control | Product Specifications | 1. ON ( 2. AUTO Button 3. MENU ( 4. Move (▲ ▼ ◀ ▶)/( 5. V.KEYSTONE(+/-) ) Button ) Button ) Button (VERTICAL KEYSTONE)Button 6. VIDEO Button 7. S-VIDEO Button 8. P.SIZE Button 9. COMP Button 10. OFF ( ) Button 11. RETURN ( ) Button 12. BLANK Button 13. INFO STILL Button 14. HDMI Button 15.
8. P.SIZE Used to adjust the size of picture screen. 9. COMP Used to switch to COMPONENT Mode. 10. OFF ( ) Used to turn off the projector. 11. RETURN ( ) Returns to the previous menu. 12. BLANK This is used to turn off the screen temporarily. It is released when any button other than the ON/OFF button is pressed. 13. INFO STILL INFO: Used to check source signals, picture setup, PC screen adjustment and lamp lifespan. STILL: Used to see still images. 14. HDMI Used to switch to HDMI Mode. 15.
Power Less than 350W Consumption Power Voltage 110/220 Vac +/-10 %, 50/60 Hz +/-3 Hz Noise Eco : 30dB, Bright : 32dB 343.1 mm(W)x162.4 mm(H)x347.2 mm(D) Dimensions 13.5 inches(W) x 6.4 inches(D) x 13.7 inches(H) Weight 5.
Component 28.125 P 50 P 74.25 Sep. 45 P 60 P 74.25 Sep. 37.5 P 50 P 74.25 Sep. 720x480p 31.5 P 60 P 27 Sep. 720x576p 31.25 P 50 P 27 Sep. 1280x720p 640X350 640X400 640X480 720X400 800X600 1024X768 HDMI 1280X768 31.47 P 70.1 N 25.18 Sep. 37.86 P 85.1 N 31.5 Sep. 37.86 N 85 P 31.5 Sep. 31.47 N 60 N 25.175 Sep. 37.5 N 75 N 31.5 Sep. 31.47 N 70 P 28.322 Sep. 37.88 P 60 P 40 Sep. 46.87 P 75 P 49.5 Sep. 48.36 N 60 N 65 Sep.
Picture Position Modes The position function is not supported in HDMI, Video and S-video input.
| Basic Settings | Connecting the Power | Connecting to video equipment | Installing the Projector Install the projector so that the beam from the projector is perpendicular to the screen. Place the projector so that the lens is at the center of the screen. If the screen is not vertically installed, the picture on the screen may not be a rectangle. Do not install the screen in bright surroundings. If the screen is too bright, the picture on the screen will not be displayed clearly.
You can adjust the size of image within zoom range by manipulating the Zoom Knob. Focus the picture on the screen using the Focus Ring. If your product is installed at a location out of the specified projection distance (refer to Screen Size and Projection Distance), the focus cannot be adjusted correctly. Leveling with Adjustable Feet For level placing of the projector, adjust the Adjustable Feet of the projector. You may adjust the level of the projector up to 12 mm (average 3.4°) degrees.
This projector is designed to show images optimally on a 80 ~ 120 inch sized screen. A. Screen Z: Throw Distance Y': Distance from Lens Center to Image Bottom Setting up the PC Environment - Check the following items before connecting your PC to your projector. 1. Click the right mouse button on the Windows desktop and click on [Properties]. tab will appear. 2.
5. Click the [OK] button to close the window, and click the [OK] button of the window to close the window. The computer may restart automatically. 6. Shut down the PC and connect to the projector. Process might vary depending on your type of computer or Windows versions. (For example, [Properties] appears instead of [Properties (R)] as shown in 1.) This unit appliance supports up to 24 bits per pixel in Color quality when it is used as a PC monitor.
Connecting a DVD player/Cable/Satellite Box to HDMI/DVI - Connecting using an HDMI/DVI cable Connect the [HDMI/DVI IN] terminal on the back of the projector and the DVI output terminal of the DVD player/Cable/Satellite box using a HDMI/DVI cable. - Connecting using an HDMI cable Connect the [HDMI/DVI IN] terminal on the back of the projector and the HDMI output terminal of the DVD player/Cable/Satellite box using a HDMI cable.
Component Ports are marked as (Y/PB/PR), (Y, B-Y, R-Y) or (Y, Cb, Cr) depending on the manufacturer. Connecting to VCR/Camcorder Connect [VIDEO IN(yellow)] input port of the projector to the VIDEO (yellow) OUT port of video equipment using the video cable. - If the video equipment has S-VIDEO OUT port, connect it to [S-VIDEO IN] input port of the projector. Using the S-VIDEO connection, provides a higher visual quality. When finishing connecting the devices, connect the power of the projector and the VCR.
Connect [PC IN] port on the rear side of the projector to the monitor output port of the PC using a PC video cable. When connections are all completed, connect both power cords of the projector and the PC. This product supports plug and play, therefore you do not need to install a driver on your PC. Using the Projector Turn on the projector and press the [PC] button to select . If PC Mode is not available, check PC video cable is in place. Turn on the PC and set the PC Environment when necessary.
| Input | Picture | Setup | Option | * Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Source List )/Stop( Play/Stop You can select a device connected to the projector to display. 1) Component 4) PC 2) S-Video 5) HDMI 3) Video Edit Name You can edit the names of devices connected to the projector.
* Click the Play( Screen ) button in the table below to view the video file. Description Adjustment Mode )/Stop( Play/Stop Select a screen state which is customized to your projector or change the screen mode as required. 1) Mode - Dynamic Select this mode for a brighter and sharper picture than Standard Mode. - Standard This is the picture mode optimized to the standard broadcast signal. - Monitor1 This is the brightest picture mode appropriate for a presentation.
G-Gain emphasized. - 9300K : The color temperature appropriate to very bright places such as a shop. 1) Color Temperature 5) R-Offset 2) R-Gain 6) G-Offset 3) G-Gain 7) B-Offset B-Gain R-Offset G-Offset B-Offset 4) B-Gain 8) Gamma : An image compensation function that controls the settings according to the video properties. ▶ This cannot be used in [Monitor1] and [Sports] modes. - Film : The best setting for watching a film. Gamma - Video : The best setting for watching a TV program.
shaking. If the noise is not removed using Fine Adjustment, adjust the frequency to the maximum and then perform Fine Adjustment again. Auto Only activated in the PC environment. Adjustment 1) Auto Adjustment : Used to adjust frequency and phase of PC screen Coarse automatically. 2) Coarse : Used to adjust frequency when vertical lines appear on PC screen. 3) Fine : Used to fine tune the PC screen.
can comfortably watch pictures on the screen even when watching under dark conditions. It also lowers power consumption and extends the life of the lamp. Bright 2) Bright : Used to enhance the brightness in relatively bright ambient light. Since this mode increases the light level of the lamp, you may experience more noise which is produced when the projector is cooled down. V-Keystone If video scences are distorted or tilted, you can compensate for this using the vertical Keystone function.
* Click the Play( Screen )/Stop( ) button in the table below to view the video file. Description Adjustment Language You can select the Language used for the menu screen. Menu Option You can adjust the settings related to the menu screen. Play/Stop 1) Position : You can move the location of the menu to a new position (up/down/right/left). 2) Transparency : Selects the transparency of the menu screen.
| Before Contacting Service Personnel | Installation and Connection Symptoms Troubleshooting No Power. z Check the power cable connections. I want to install my projector on z The ceiling installation support is sold separately. Contact your local product distributor. the ceiling. External Source can not be z Be sure that the connection cable(s) (video) is properly connected to the proper port. If the device is not connected properly, it can not be selected. selected.
odd color./ screen is too dark or bright. Contrast and Color in the menu. z If you want to restore various settings to their factory defaults, run from the menu.
| Care and Maintenance | Contact SAMSUNG WORLDWIDE | Other | Authority | To clean the exterior and lens of the projector Clean the projector using a soft dry cloth. Do not clean the projector with flammable substances such as benzene, thinners or a wet cloth, as these may cause problems. Do not touch the projector with a nail or any other sharp objects, as this may scratch the surface.
When handling the lamp, avoid touching any part of it except for the handles. If you handle the lamp incorrectly, it may affect the screen quality and shorten its lifetime. Contains Mercury, Dispose According to Local, State or Federal Laws Lamp Replacement Procedure The lamp is very hot and operates The lamp is located at the bottom Slide and open the cover in the with a high voltage. Allow it to cool of the product.
ARGENTINA BRAZIL 0800-333-3733 http://www.samsung.com 0800-124-421 http://www.samsung.com 4004-0000 CHILE 800-SAMSUNG(726-7864) http://www.samsung.com COLOMBIA 01-8000112112 http://www.samsung.com COSTA RICA 0-800-507-7267 http://www.samsung.com ECUADOR 1-800-10-7267 http://www.samsung.com EL SALVADOR 800-6225 http://www.samsung.com GUATEMALA 1-800-299-0013 http://www.samsung.com HONDURAS 800-7919267 http://www.samsung.com JAMAICA 1-800-234-7267 http://www.samsung.
022 - 607 - 93 - 33 PORTUGAL 80820 - SAMSUNG (726-7864) http://www.samsung.com SLOVAKIA 0800-SAMSUNG(726-7864) http://www.samsung.com SPAIN 902 - 1 - SAMSUNG (902 172 678) http://www.samsung.com SWEDEN 0771 726 7864 (SAMSUNG) http://www.samsung.com http://www.samsung.com/ch SWITZERLAND 0848-SAMSUNG(7267864, CHF 0.08/min) http://www.samsung.com/be_fr (French) U.K 0845 SAMSUNG (7267864) http://www.samsung.
1-800-10-SAMSUNG(726-7864) PHILIPPINES 1-800-3-SAMSUNG(726-7864) 1-800-8-SAMSUNG(726-7864) http://www.samsung.com 02-5805777 SINGAPORE 1800-SAMSUNG(726-7864) http://www.samsung.com TAIWAN 0800-329-999 http://www.samsung.com 1800-29-3232 THAILAND http://www.samsung.com 02-689-3232 VIETNAM 1 800 588 889 http://www.samsung.com MIDDLE EAST & AFRICA BAHRAIN 8000-4726 JORDAN 800-22273 SOUTH AFRICA 0860-SAMSUNG(726-7864) http://www.samsung.com TURKEY 444 77 11 http://www.samsung.com U.A.
Digital Broadcast is a television broadcasting signal digitized and transmitted according to the United States terrestrial digital broadcast specifications, or ATSC. DVD (Digital Versatile Disc) DVD is a large capacity media disk that can save multimedia content such as video, games, audio applications, etc. using MPEG-2 video compression technology on a CD size disc.