D-1 y Standard BIOS POST 코드 D-5 y Recovery Beep 코드 D-6 y D-6 y BMC Beep 코드 에러 코드와 메시지
D-1 부록 D 에러 메시지와 Beep 코드 SmartServer 210(SS210)에서 Beep 코드가 에러 발생을 알리고 시스템 BIOS가 이 에러 메시지를 모니터상에서 보여줍니다. POST(Power on Self Test) 에러 코드는 NVRAM과 확장(Extended) BIOS에 정의되어 있습니다. I/O location 80h에 2-digit의 hex code를 써서 비디오 어댑터를 초기화 시킨 후에 POST가 수행 되는데 이 때 BIOS는 에러 시험단계를 갖습니다.
D-2 부록 D 에러 메시지와 Beep 코드 (계속) CP Beeps 발생 원인 28 1-3-3-1 Autosize DRAM, System BIOS stops execution here if the BIOS does not detect any usable memory DIMMS Clear 8 MB base RAM 2A 2C 1-3-4-1 Base RAM failure.
D-3 (계속) CP Beeps 발생 원인 60 Test extended memory 62 Test extended memory address lines 64 Jump to UserPatch1 66 Configure advanced cache registers 68 Enable external and processor caches 6A Display external cache size 6B Load custom defaults if required 6C Display shadow message 6E Display non-disposable segments 70 Display error messages 72 Check for configuration errors 74 Test real-time clock 76 Check for keyboard errors 7A Test for key lock on 7C Set up hardware interrup
D-4 부록 D 에러 메시지와 Beep 코드 (계속) CP Beeps 발생 원인 9C Set up Power Management 9E Enable hardware interrupts A0 Set time of day A2 Check key lock A4 Initialize typematic rate A8 Erase F2 prompt AA Scan for F2 key stroke AC Enter SETUP AE Clear in-POST flag B0 Check for errors B2 POST done-prepare to boot Operating System B4 1 One short beep before boot B5 Display MultiBoot menu B6 Check password, password is checked before option ROM scan B7 ACPI initialization B8 Clear global
D-5 Recovery BIOS POST 코드 CP Beeps 발생 원인 E0 Initialize chip set E1 Initialize bridge E2 Initialize processor E3 Initialize timer E4 Initialize system I/O E5 Check Forced recovery boot E6 Validate checksum E7 Go to BIOS E8 Initialize processors E9 Set 4 GB segment limits EA Perform platform initialization EB Initialize PIC and DMA EC Initialize memory type ED Initialize memory size EE Shadow boot block EF Test system memory F0 Initialize interrupt services F1 Initialize
D-6 부록 D 에러 메시지와 Beep 코드 BMC Beep 코드 Beeps 발생 원인 1-5-1-1 FRB failure (processor failure) 1-5-4-2 Power fault: DC power unexpectedly lost (power control failures) 1-5-4-3 Chipset control failure 1-5-4-4 Power control fault 에러 메시지와 코드 코드 에러 메시지 에러 상태 0200: Failure Fixed Disk Hard disk error 0210: Stuck Key Keyboard connection error 0211: Keyboard error Keyboard failure 0212 Keyboard Controller Failed Keyboard Controller Failed 0213: Keyboard locked-Unlock key switch Keyboard locke
D-7 (계속) 코드 에러 메시지 에러 상태 02B2: Incorrect Drive A type-run SETUP Incorrect Drive A type 02D0: System cache error-Cache disabled CPU cache error 0B00: Rebooted during BIOS boot at Post Code 0B1B: PCI System Error on Bus/Device/Function PCI system error in Bus/device/Function 0B1C: PCI Parity Error in Bus/Device/Function PCI system error in Bus/device/Function 0B50: Processor 1 with error taken offline Failed Processor 1.
D-8 부록 D 에러 메시지와 Beep 코드 (계속) 코드 에러 메시지 에러 상태 0B95: BMC FRU device failure SROM storing chassis information failed (Available for use except for FRU command and emergency management port function) 0B96: BMC SDR Repository failure BMC device (chip) failed 0B97: BMC SEL device failure BMC device (chip) failed 0BB0: SMBIOS-SROM data read error SROM data read error 0BB1: SMBIOS-SROM data checksum bad Bad checksum of SROM data 0BD0: 1st SMBus device address not acknowledged Some SMBus devi
주 의 사 항 y 이 설명서의 저작권은 삼성전자주식회사에 있습니다. y 이 설명서의 일부 혹은 전부를 삼성전자의 허가없이 전자적, 기계적, 음향적인 어떤 수단으로도 재 생산하거나 전송할 수 없습니다. y 이 설명서의 내용은 제품의 기능 향상 등을 이유로 변경될 수 있습니다. Copyrightⓒ SAMSUNG All rights Reserved. 은 삼성의 등록상표입니다. SS210은 삼성전자의 등록상표입니다. 이외의 회사명이나 제품명은 해당 회사 소유의 등록상표입니다.