System Keyboard SSC-2000 User's Manual GB F D ES I R P
GB-2 CAUTION RISK OF ELECTRIC SHOCK DO NOT OPEN CAUTION : TO REDUCE THE RISK OF ELECTRIC SHOCK, DO NOT REMOVE COVER (OR BACK). NO USER SERVICEABLE PARTS INSIDE. REFER SERVICING TO QUALIFIED SERVICE PERSONNEL. This symbol indicates high voltage is present inside. It is dangerous to make any kind of contact with any inside part of this product. This symbol alerts you that important literature concerning operation and maintenance has been included with this product.
Contents Chapter 1. General Facts ........................................................gb-3 Introduction ............................................................gb-3 Features ..................................................................gb-3 Name and function of each part ............................gb-3 Chapter 2. Installation ............................................................gb-4 Installation Environment Setup .............................gb-4 Cautions for Installation ...............
GB-4 B. Camera movement key - PRESET - PATTERN - SCAN - AUTO PAN C. Alarm release key D. Joystick controller (UP/DOWN/LEFT/DOWN/AF/ZOOM) The Pan/Tilt connected with Samsung Dome Camera or Receiver Unit is moved to UP/DOWN/LEFT/RIGHT. Press the button on the top of Joystick to control the Auto Focus. And use for the zoom control by turning to the clockwise or counterclockwise. The function of UP/ DOWN/LEFT/RIGHT keys is controlled in the menu screen of the connected controller.
• Be sure to check dangers, which may occur due to damped floor, ungrounded power extension cable, worn power cord or lack of safety grounding. Caution When cleaning this unit, be sure to wipe with a dried cloth. If the unit is heavily contaminated, wipe it with a soft cloth dampened with a mild detergent solution, then wipe dry with a soft clean cloth. Do not use chemicals such as alcohol, benzene, or thinner because a chemical reaction could result permanent damaging of the cabinet surface.
GB-6 • In case of connecting with Full Duplex - Connect the Txd (+) of Dome Camera RS-485 port with the Rx (+) of SSC-2000. - Connect the Txd (-) of Dome Camera RS-485 port with the Rx (-) of SSC-2000. - Connect the Rxd (+) of Dome Camera RS-485 port with the Tx (+) of SSC-2000. - Connect the Rxd (-) of Dome Camera RS-485 port with the Tx (-) of SSC-2000. 2) Connecting SHR-3091 & SHR-3161 DVR (Applicable to the Version 1.
) Connecting PC based DVR (Applicable to the SPR Smart View V2.3 over) - Connect the Tx (+) of SSC-2000 port with the Tx (+) of another SSC-2000. - Connect the Tx (-) of SSC-2000 RS-485 port with the Tx (-) of another SSC-2000. 2) In case of connecting with Full Duplex - Connect SSC-2000 through the RS-485 port in the back of PC BASED DVR. - Connect SIGNAL (+) in the RS-485 port of PC BASED DVR with Tx (+) of SSC-2000. - Connect SIGNAL (-) in the RS-485 port of PC BASED DVR with Tx (-) of SSC-2000.
GB-8 Chapter 4. Instructions Log-in If the key board is not operated for three seconds, the graphic panel is changed to the sleep mode and the screen is not displayed.(Blue Screen display) Press the touch panel/key or move the joystick/joy shuttle, and then the screen before the sleep mode is displayed again. 1. Turn on the power of all the components of the system. 2.
PATTERN movement PRESET DELETE This function is to view the camera movement for 30 seconds designated by the user on the pattern mode of the camera menu. Press the pattern button on the keyboard, enter the pattern number(1~3) you want, and press “ENTER” to execute PATTERN movement. “PATTERN 1” will appear on the screen. • If there is any of MANUAL (PAN, TILT, ZOOM, FOCUS) input during auto execution (SCAN, AUTO PAN, PATTERN), the system will stop the AUTO movement and execute the MANUAL movement.
CAMERA connection information GB-10 Press the part marked as shown below to know the number of DVR and MUX that are con nected to the selected camera. English small letter input page will appear. Press “TEXT” if you want to enter large letters. A window will appear as shown below when you press the camera number display part. Press “NUMBER” if you want to enter numbers.
CAMERA MENU DVR channel selection Press the “SETUP” ICON on left below to control the menu of the selected camera. 1. Press the “CH” ICON below on the DVR screen. 2. A channel selection screen will appear as shown below. Using the direction key and the enter key, control the CAMERA MENU. Press the EXIT ICON to clear the camera menu. 3. Select the channel you want. 4.
Using the number keys, enter the correct Operator No. and Password. MAIN MENU will be displayed on the screen when you complete the log-in process. GB-12 MUX channel selection 1. Press the “CH” ICON below on the MUX screen. 2. A channel selection screen will appear as shown below. Press the item you want to control on the main menu. Press the EXIT ICON in the main menu to return to the camera control mode. • If the CHECK PASSWORD item is set “Off” in the keyboard setup, press the “MENU” button.
ADDRESS SET The address of the system keyboard can be set. Press “ADDRESS SET” and the keyboard address input window will appear as shown below. Enter the address by using the number keys and press the enter key. Press enter the “EXIT” ICON on lower left if you want to clear the window without entering the address. • The ADDRESS of the keyboard can be set as 0 ~ 32. • - ADDRESS “0” : STAND ALONE - ADDRESS “1” : MASTER - ADDRESS “2~32” : SLAVE • If you use a keyboard, it should be set to “0”.
GB-14 PARITY CHECK Confirm New Password The PARITY BIT of RS-232 communication can be set. Press “PARITY CHECK” and a pop-up window will appear as shown below. This is to confirm the new password. Enter the password by using the number keys (0~9) and press the enter key. If the entered number is not same as the New Password, an error message “Invalid Password!!” will be displayed on the screen. You have to start again from entering the operator’s number.
DOWNLOAD process screen A download process screen will appear as shown below when you press “OK” on the down load check screen. - Operator No. : Newly registered use's number - Password : New password is displayed.(******) - Operator Level : The level of the new user can be set. A message will appear when downloading is completed. Operator Level Press “Operator Level” to set the level. You can choose one level among Admin. / Manager / Operator. • DEFAULT OPERATOR LEVEL is OPERATOR level.
GB-16 UPLOAD progress screen Factory Default Setup When you press “OK” on the UPLOAD check screen, UPLOAD progress screen will appear as shown below. Resets all of the menu values to the default value. Press “OK” to start the default setting. ‘Complete’ message will appear when uploading is completed. • The system will start again when the FACTORY DEFAULT SETUP is completed. Chapter 6. OPERATOR LEVEL There are 3 levels of user, who can be registered as a user, including Admin. / Manager / Operator.
Chapter 7. Product Specification Chapter 8. Q & A ITEM INTERFACE (RS-485) INTERFACE (RS-232C) LCD PANEL LED PAN/TILT & LENS CONTROL DVR CONTROL POWER POWER CONSUMPTION DIMENSIONS (WxHxD) WEIGHT (kg) DESCRIPTION CONNECTOR TYPE : 4P TERMINAL TYPE PORT : 1 PORT BAUD RATE : 4,800/9,600/19,200/38,400bps CONNECTOR TYPE : D-SUB 9P PORT : 1 PORT BAUD RATE : 600/1,200/2,400/4,800/ 9,600/19,200/38,400/57,600bps 5.
GB-18
