Before attempting to operate this product, please read the instructions carefully.
Cautions and Warnings for Use Samsung Techwin cares for the environment at all product manufacturing stages to preserve the environment, and is taking a number of steps to provide customers with more environment-friendly products. The Eco mark represents Samsung Techwin's will to create environment-friendly products, and indicates that the product satisfies the EU RoHS Directive. Thank you for purchasing our products.
Product Category ■ 1. Product Category ■ 1.1. Housing Accessories STH-380PO/STH-370PO/STH-360PO : "Outdoor housing” with a built-in install base for the Samsung Speed Dome Camera. STH-380PO : Ultra Low-Temperature Heavyweight(-40℃~50℃) STH-370PO : Low-Temperature Heavyweight(-20℃~50℃) STH-360PO : Low-Temperature Lightweight(-20℃~50℃) Product Category ■ 1.2. Interface Mounting Accessories STB-370PC : “On-Ceiling Install Base Mount” for the Samsung Speed Dome Camera. ■ 1.3.
Product Category STB-30PF : “Ceiling Type Flange” for the Samsung Speed Dome Camera. Speed Dome Camera Installation Category ■ 2. Speed Dome Camera Installation Category Pendant Type STB-350PPM : Parapet Mount” for the installation of indoor or outdoor housing of Samsung Speed Dome Camera STB-330PPM Wall Type Mount Ceiling Type Mount Indoor Flange Type Mount : “Pole Mount” for the Samsung Speed Dome Camera. On-Ceiling Mount Type STB-340PCM : “Corner Mount” for the Samsung Speed Dome Camera.
Pendant Type Installation STH-380PO/370PO/370PI/360PO STH-380PO/370PO/370PI/360PO ■ 3. Pendant Type Installation Pendant Type Installation 1. Securing Wall Bracket and Wiring As shown in the picture, secure the wall bracket to the wall, and then pull the wires out of the bracket. Please note that the STH-380PO housing requires an additional installation of the fan heater adapter enclosed with the product. ■ 3.
Pendant Type Installation Fan Heater Connector (Model: STH-370PO) STH-380PO/370PO/370PI/360PO STH-380PO/370PO/370PI/360PO Fan Heater Adaptor (STH-380PO Only) Pendant Type Installation 5. Securing Housing Check if the housing is properly attached to the bracket, secure the housing to the bracket with the enclosed screws. Camera Adaptor 6. Wiring Terminal Cables Connect the cables to the terminal block on the hinged door. Once the wiring is successful, close the hinged door.
Pendant Type Installation Pendant Type Installation Video Output Alarm STH-380PO/370PO/370PI/360PO STH-380PO/370PO/370PI/360PO ✽ Camera Wiring Diagram This wiring diagram indicates the connection between the interface board and external equipment. For wiring Samsung Techwin’s Speed Dome Camera and the accessories, please refer to the Speed Dome Camera user’s manual. 7. Preparing Camera Once the camera wiring is successful, prepare the camera.
Pendant Type Installation STH-380PO/370PO/370PI/360PO STH-380PO/370PO/370PI/360PO ✽ To attach or detach the camera, refer to the picture. * Attaching the camera: Hold up the camera and push it to the mount as shown in the picture. Push the camera until you hear a “click”. * Detaching the camera: To detach the camera, pull the camera downward while pushing the unlock buttons on the camera upward. Pendant Type Installation ■ 3.
Pendant Type Installation Pendant Type Installation STH-380PO/370PO/370PI/360PO STH-380PO/370PO/370PI/360PO ■ 3.3 Indoor Flange Mount Type Installation Camera Adaptor Fan Heater Adaptor (STH-380PO Only) This guideline is based on the installation of the indoor flange STB-25PF and the ceiling exposed mount STB-370PC. Sealing Tape SPSS32A/SCH40 Size Pipe STB-30PF PF 1 1/4" 1. Preparing Pipe and Ceiling Bracket STB-30PF requires a SPSS32A/SCH40-sized pipe as shown in the picture.
Pendant Type Installation STH-380PO/370PO/370PI/360PO STH-380PO/370PO/370PI/360PO 1. Assembling Flange and Ceiling Exposed Mount (STB-370PC) Wind sealing tape around the barrel of the screw taps, and then secure the STP-25PF flange securely to the mount with the enclosed screws. Pendant Type Installation Notes • Do not connect the camera to a power outlet until the installation is complete. Supplying power in the middle of the installation may cause fire or damage the product. 4.
Pendant Type Installation STH-380PO/370PO/370PI/360PO 6. Attaching Camera Carefully attach the camera to the mount following the alignment guide marks as shown in the picture. First hook the camera's safety cable on the mount, and then attach the camera. The safety cable is coiled inside the install base. As shown in the leftward picture, pull out the safety cable from the install base and then hook it to the mount. On-Ceiling Mount Type Installation ■ 4.
On-Ceiling Mount Type Installation 1. Attaching Template and Installing STB-370PC Attach the enclosed template to the ceiling, then drill a hole in the ceiling according to the diameter marked on the template. Drop the camera cables down from the ceiling through the hole. Next, install the Install Base STB-370PC to the ceiling as shown in the picture. Before installing the exposed bracket, open the hinged door at the bottom of the bracket as shown in the picture. Hold the knob on the hinged door to open.
On-Ceiling Mount Type Installation ✽ To attach or detach the camera, refer to the picture. * Attaching the camera: Hold up the camera and push it to the mount as shown in the picture. Push the camera until you hear a “click”. * Detaching the camera: To detach the camera, pull the camera downward while pushing the unlock buttons on the camera upward. Indoor Flush Mount Type Installation ■ 5. Indoor Flush Mount Type Installation This guideline is based on the installation of the flush mount STH-370PE.
Indoor Flush Mount Type Installation 1. Attaching Flexible Adaptor To feed the cables through a pipe to a flush housing, attach the flexible adaptor enclosed with the product. To attach the flexible adaptor, the install base must be disassembled as shown in the picture. To disassemble the install base, unscrew the 3 screws on the bottom. Silicon Cap Indoor Flush Mount Type Installation 4. Preparing Housing Open the hinged door at the bottom of the housing.
Indoor Flush Mount Type Installation 7. Arranging Camera Cables and Closing Hinged Door Connect the cables to the terminal block on the hinged door. For the location of the wiring pins, please refer to the “Camera Wiring Diagram” on Page 12. Once the wiring is successful, close the hinged door. Indoor Flush Mount Type Installation Notes • Make sure to first hook the camera's safety cable to the mount before proceeding. Otherwise you may be exposed to serious injury caused by a fallen camera. 8.
Mounting Accessory Installation ■ 6. Mounting Accessory Installation Mounting Accessory Installation ■ STB-270B(Setup Box) This guideline is to be used for the installation of mounting accessories for the Samsung Speed Dome Camera series. 1. U sing self drilling screws, secure the install bracket. 2. F ill unwanted wire holes with mount caps. Secure the mount cap with the mount cap fastener. MOUNT CAP MOUNT CAP FASTENER 3. P lace the setup box on the install bracket as shown in the picture.
Mounting Accessory Installation Mounting Accessory Installation ■ STB-330PPM (Paul Mount) ■ STB-350PPM (Parapet Mount) Compatible Models : STB-270PWV+STH-380PO/370PO/360PO/370PI Compatible Models : STB-30PF+STH-380PO/370PO/360PO/370PI Wall type mount 1. Secure the pole to the mount using a wire or cable. 2. U se 4 1/4" screws to secure the STH-270PWV pole mount to the wall. 1. D rill 8 anchor bolt holes on the wall according to the holes in the parapet mount. 2.
Product External Dimensions ■ Wall Mounting Product External Dimensions Unit : mm ■ Ceiling Mounting ■ Ceiling Exposed Mounting 34 SPEED DOME CAMERA ACCESSORIES Unit : mm ■ Indoor Flush Mounting SPEED DOME CAMERA ACCESSORIES 35
Product Specifications Product Specifications Model Item Operating Temperature Range STH-380PO STH-370PO STH-370PI STH-370PE STH-360PO -40℃~50℃ -20℃~50℃ -10℃~50℃ -10℃~50℃ -20℃~50℃ 0 to 90%RH 1 to 90%RH 0 to 90%RH (non-condensing) (non-condensing) Housing Housing Housing Embedded Housing ALDC 12 ALDC 12 ALDC 12 E.G.I (1.
MEMO MEMO
SALES NETWORK • AMSUNG TECHWIN CO.,LTD. S 145-3, Sangdaewon-dong, Jungwon-gu, Seongnam-si, Gyeonggi-do, 462-120, Korea TEL : +82-31-740-8151~8 FAX : +82-31-740-8145 • AMSUNG TECHWIN AMERICA,LTD. S 1480 Charles Willard St. Carson, CA 90746, UNITED STATES TEL : +1-310-632-1234 FAX : +1-310-632-2195 • AMSUNG OPTO-ELECTRONICS UK,LTD. S Samsung House, 1000 Hillswood Drive, Hillswood Business Park Chertsey Surrey KT16 OPS TEL : +44-1932-45-5308 FAX : +44-1932-45-5325 www.samsungtechwin.com www.