SyncMaster 214T Install drivers Install programs
Notational Failure to follow directions noted by this symbol could result in bodily harm or damage to equipment. Prohibited Important to read and understand at all times Do not disassemble Disconnect the plug from the outlet Do not touch Grounding to prevent an electric shock Power When not used for extended period of time, set your computer to DPMS. If using a screen saver, set it to the active screen mode.
Do not use a damaged or loose plug. z This may cause an electric shock or fire. Do not pull the plug out by the wire nor touch the plug with wet hands. z This may cause an electric shock or fire. Use only a properly grounded plug and receptacle. z An improper ground may cause electric shock or equipment damage. Insert the power plug firmly so that it does not come loose. z A bad connection may cause fire.
Do not drop the monitor when moving it. z This may cause damage to the product or human body. Install the monitor base in a showcase or shelf so that the end of the base does not protrude from the showcase or shelf. z Dropping the product may cause damage to the product or personal injury. Do not place the product on an unstable or small surface area. z Place the product on an even, stable surface, as the product may fall and cause harm to someone walking by, specifically children.
Do not place the monitor face down. z The TFT-LCD surface may be damaged. Installing a wall bracket must be done by a qualified professional. z z Installation by unqualified personnel may result in injury. Always use the mounting device specified in the owner's manual. When installing the product, make sure to keep it away from the wall (more than 10cm/4inch ) for ventilation purposes.
Unplug the power cord from the power outlet and wipe the product using a soft, dry cloth. z Do not use any chemicals such as wax, benzene, alcohol, thinners, insecticide, air freshener, lubricant or detergent. Contact the Service Center or Customer Center for interior cleaning once a year. z Keep the product's interior clean. Dust which has accumulated in the interior over an extended period of time may cause malfunction or fire. Others Do not remove cover (or back).
Do not try to move the monitor by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not move the monitor right or left by pulling only the wire or the signal cable. z This may cause a breakdown, electric shock or fire due to damage to the cable. Do not cover the vents on the monitor cabinet. z Bad ventilation may cause a breakdown or fire. Do not place water containers, chemical products or small metal objects on the monitor.
Adjust the resolution and frequency to the levels appropriate for the model. z Inappropriate resolution may cause undesirable picture quality. 21 inch (54cm) - 1600 X 1200 @ 60 Hz Watching the monitor continuously at a too close angle may result in eyesight damage. To ease eye strain, take at least a five-minute break after every hour of using the monitor. Do not install the product on an unstable, uneven surface or a location prone to vibrations.
HAS Stand : Height Adjustable & Pivot Stand (214T : 100mm) PIP/PBP : Uses MagicTune to adjust PIP for the best viewing position Adopts MagicColor Pro to make adjustments of a variety of colors at an expert level Color Weakness : Enables those with color weakness to view the screen as easily as those with normal vision. Auto Rotation applied (Implemented by MagicRotation) SyncMaster 214T Please make sure the following items are included with your monitor. If any items are missing, contact your dealer.
Quick Setup Guide User's Guide, Monitor Driver, Warranty Card Natural Color, MagicTune™, (Not available in all locations) MagicRotation software Cable D-sub Cable Power Cord DVI Cable Sold separately S-Video Cable Set-Bracket Front Video Cable Screws (4EA)
Opens the OSD menu. Also use to exit the OSD menu or return to the previous menu. MENU button [ ] Adjust buttons [ ] These buttons allow you to adjust items in the menu. Analog/Digital(PC) : MagicBright™ button [ ] MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Custom, Entertain, Internet, and Text. Each mode has its own preconfigured brightness value.
provides a sharp image. 3) Movie Select this mode when the surroundings are dark. This will save power and reduce eye fatigue. 4) Custom Select this mode when you want to adjust the image according to your preferences. >>Click here to see an animation clip Brightness button [ ] ( Available in Analog Mode Only ) When OSD is not on the screen, push the button to adjust brightness. >>Click here to see an animation clip Enter button [ ] / SOURCE button Activates a highlighted menu item.
POWER S/W : Switch the monitor on and off. POWER IN : Connect the power cord for your monitor to the POWER IN on the back of the monitor. DVI IN (Source List : Digital) : Connect the DVI cable to the DVI IN port on the back of your monitor. RGB IN (Source List : Analog) : Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor.
: External device (video) input terminal S-VIDEO (Source List : S-Video) : External device (S-video) input terminal Kensington Lock : The Kensington lock is a device used to physically fix the system when using it in a public place. (The locking device has to be purchased separately.) For using a locking device, contact where you purchase it. Stand Height Adjustment 1. Press the top side of the stand and then push the button at the rear bottom of the stand. 2.
Connecting the Monitor 1. Connect the power cord for your monitor to the POWER IN on the back of the monitor. Plug the power cord for the monitor into a nearby outlet. 2-1. Using the D-sub (Analog) connector on the video card. Connect the signal cable to the 15-pin, RGB IN port on the back of your monitor. 2-2. Using the DVI (Digital) connector on the video card. Connect the DVI cable to the DVI IN port on the back of your monitor. 2-3. Connected to a Macintosh.
Cable Fix Ring. Connecting to Other devices This monitor allows the user to connect it to such input devices as a DVD player, a VCR or a camcorder without disconnecting the PC. The configuration at the back of the monitor may vary from product to product. 1. Connecting AV Devices The monitor has AV connection terminals to connect AV input devices like DVD, VCR or Camcorder. You may enjoy AV signals as long as the monitor is turned on. 1.
1. Input devices such as digital DVD are connected to the DVI IN terminal of the monitor using the DVI cable. 2. Then, start the DVD with a DVD disc inserted. 3. Select Digital using the SOURCE button.
Using (a), you can rotate the screen within a range of 0 ~ 90 degrees. Using (b), you can use the screen lengthwise. Press the top side of the stand and then push the button at the rear bottom of the stand. You can adjust the stand height using this button. When you are using a stand height as maximum, it will go down a little bit from spring elasticity. If you rotate the screen without lifting it to its maximum height, the screen may be damaged because the edge of the screen would hit the floor.
A. Monitor B. Mounting interface pad (sold separately) 1. Turn off your monitor and unplug its power cord. 2. Lay the LCD monitor face-down on a flat surface with a cushion beneath it to protect the screen. 3. Remove four screws and then remove the stand from the LCD monitor. 4. Align the mounting interface Pad with the holes in the rear cover mounting pad and secure it with four screws that came with the arm-type base, wall mount hanger or other base.
4. Click the "Install" button in the "Warning" window. 5. Monitor driver installation is completed. Windows XP/2000 1. Insert CD into the CD-ROM drive. 2. Click "Windows XP/2000 Driver" 3. Choose your monitor model in the model list, then click the "OK" button. 4. If you can see following message window, then click the "Continue Anyway" button. Then click "OK" button. This monitor driver is under certifying MS logo,and this installation don't damage your system.
Installing the Monitor Driver (Manual) Windows XP | Windows 2000 |Windows Me |Windows NT | Linux When prompted by the operating system for the monitor driver, insert the CD-ROM included with this monitor. Driver installation is slightly different from one operating system to another. Follow the directions appropriate for the operating system you have. Prepare a blank disk and download the driver program file at the Internet web site shown here. z Internet web site : http://www.samsung.
5. Click "Update Driver.." and select "Install from a list or.." then click "Next" button. 6. Select "Don't search ,I will.." then click "Next" and then click "Have disk". 7. Click the "Browse" button then choose A:(D:\Driver) and choose your monitor model in the model list and click the "Next" button. 8. If you can see following "Message" window, then click the "Continue Anyway" button. Then click "OK" button.
10. Monitor driver installation is completed. Microsoft® Windows® 2000 Operating System When you can see "Digital Signature Not Found" on your monitor, follow these steps. 1. Choose "OK" button on the "Insert disk" window. 2. Click the "Browse" button on the "File Needed" window. 3. Choose A:(D:\Driver) then click the "Open" button and then click "OK" button. How to install 1. 2. 3. 4. 5. 6. 7. 8. 9. 10. Click "Start" , "Setting" , "Control Panel". Double click the "Display" Icon.
Microsoft® Windows® NT Operating System 1. Click Start, Settings, Control Panel, and then double-click Display icon. 2. In Display Registration Information window, click Settings Tab and then click All Display Modes. 3. Select a mode that you wish to use (Resolution, Number of colors and Vertical frequency) and then click OK. 4. Click Apply button if you see the screen working normally after clicking Test.
How to install the Natural Color software Insert the CD included with the Samsung monitor into the CD-ROM Drive. Then, the initial screen of the program Natural Color will be executed. Click Natural Color on the initial screen to install the Natural Color software. To install the program manually, insert the CD included with the Samsung monitor into the CDROM Drive, click the [Start] button of Windows and then select [Execute]. Enter D:\color\eng\setup.exe and then press the key.
MENU Use this button for open the on-screen menu and exits from the menu screen or closes screen adjustment menu. Analog/Digital(PC) : MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Then push button again to circle through available preconfigured modes. ( Custom → Entertain → Internet → Text ) Digital(DVD)/Video/S-Video: Mode The Monitor has four automatic picture settings that are preset at the factory.
AUTO : Available in Analog mode only Menu Description When the 'AUTO' button is pressed, the Auto Adjustment screen appears as shown in the animated screen on the center. Auto adjustment allows the monitor to self-adjust to the incoming video signal. The values of fine, coarse and position are adjusted automatically. (Available in Analog mode only) AUTO To make the automatic adjustment function sharper, execute the 'Auto Adjustment' function while the AUTO PATTERN is on.
Menu Description Play/Stop MENU Locked After pushing the "MENU" button more than 5 seconds, OSD function is locked (unlocked). Even if you use the OSD adjustment lock function, you can still adjust MagicBright™ and Brightness and Contrast of the monitor. Menu Description Analog/Digital(PC) : MagicBright™ MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching.
Then push button again to circle through available preconfigured modes. ( Custom → Entertain → Internet → Text ) MagicBright™ / Mode Mode Digital(DVD)/Video/S-Video : Mode The Monitor has four automatic picture settings that are preset at the factory. Then push button again to circle through available preconfigured modes.
Menu Description SOURCE Selects the input signal while the OSD is off. (When the source button is pressed to change the input mode, a message appears in the upper left of the screen displaying the current mode -Analog, Digital, Video and S-Video input signal.) Note : Changing the source is allowed only in external devices that are connected to the monitor at the time. PIP ( Available in Analog/Digital(PC) Mode Only ) Menu PIP Description Push the PIP button to turn PIP screen On/Off.
Input The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Source List Use to select PC or other external input sources connected to the Monitor. Use to select the screen of your choice. 1) Analog 2) Digital 3) Video 4) S-Video Edit Name Name the input device connected to the input jacks to make your input source selection easier.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu MagicBright™ Description Play/Stop MagicBright™ is a new feature providing the optimum viewing environment depending on the contents of the image you are watching. Currently four different modes are available: Text, Internet, Entertain and Custom. Each mode has its own pre-configured brightness value.
Image Lock may relocate it to the center using the Horizontal Control menu. 2) Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). 3) Sharpness : Adjust the Sharpness. 4) H-Position : Adjusts the screen location horizontally. 5) V-Position : Adjusts the screen location vertically. Auto Adjustment The values of Fine, Coarse, position are adjusted automatically.
The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom. You can select "Custom" which automatically recalls your personalized picture settings.
Picture (Video/S-Video) The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution. Menu Description Play/Stop The Monitor has four automatic picture settings ("Dynamic", "Standard", "Movie" and "Custom") that are preset at the factory. You can activate either Dynamic, Standard, Movie, or Custom. You can select "Custom" which automatically recalls your personalized picture settings.
: Adds a natural tone to the display. This function is only available for DVD titles supporting NTSC. (The broadcasting system is marked with "NTSC" or "PAL" above the DVD title) Tint You can switch the Size. 1) Normal 2) Zoom1 3) Zoom2 4) Wide Size Film Mode You can turn Film Mode Off / On. The Film Mode feature offers you a theater-quality viewing experience.
Color Tone Gamma Analog/Digital(PC) : Cool4 / Cool3 / Cool2 / Cool1 / Normal / Warm1 / Warm2 Digital(Digital DVD)/Video/S-Video : Cool2 / Cool1 / Normal / Warm1 / Warm2 Gamma correction changes the luminance of the colors with intermediate luminance. Increased Mode number - Displays the full screen more naturally and softer and sharpens the dark scale. Decreased Mode number - Displays the full screen sharper and improves the bright scale.
Turn the PIP Screen on or off. 1) Off 2) On PIP Source Select the input source for the PIP. Analog / Digital(PC) : Video / S-Video Mode Change the Size of the PIP window. / / / If you select , in Size, Position will not be activated. Size Position Change the Position of the PIP window. / / / Setup The default setting may different depending on the selected Input Mode (input signal source selected in External Input List) and the selected resolution.
picture, you must set the "Blue screen" mode to "Off". Picture parameters are replaced with the factory default values. Reset 1) Image Reset : Image parameters are replaced with the factory default values. - Available in Analog Mode Only 2) Color Reset : Color parameters are replaced with the factory default values.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Overview What is MagicTune™? Monitor performance can vary due to the graphics card, host computer lighting conditions and other environmental factors. In order to get the best image on a monitor requires you to adjust it for your unique setting. Unfortunately, the manual controls available to tune the image often prove to be challenging.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Installation 1. Insert the installation CD into the CD-ROM drive. 2. Click the MagicTune™ installation file. 3. Select installation Language, Click "Next". 4. When the InstallationShield Wizard window appears, click "Next." 5. Select "I agree to the terms of the license agreement" to accept the terms of use.
6. Choose a folder to install the MagicTune program. 7. Click "Install." 8. The "Installation Status" window appears.
9. 10. Click "Finish." When the installation is complete, the MagicTune executable icon appears on your desktop. Double-click the icon to start the program. Magictune execution icon may not appear depending on specification of computer system or monitor. If that happens, press F5 Key. Installation Problems The installation of MagicTune™ can be affected by such factors as the video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation.
OS z z z z z Windows™ Windows™ Windows™ Windows™ Windows™ 98 SE Me 2000 XP Home Edition XP Professional It is recommended using MagicTune in Windows™ 2000 or later. Hardware z z 32MB Memory above 25MB Hard disk space above * For more information, visit the MagicTune website.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting MagicTune allows for quick accurate tuning of the display with the ability to easily save and use monitor configurations that are best suited for you. z z z OSD mode may appear inconsistent with the explanation in guidance book depending on specification of each monitor. When Rotation is functioning, part of MagicTune Program may not operate normally.
4. Custom: Although the values are carefully chosen by our engineers, the preconfigured values may not be comfortable to your eyes depending on your taste. If this is the case, adjust the Brightness and Contrast by using the OSD menu. Color Tab Definition Adjusts the "warmth" of the monitor background or image color. MagicColor and Gamma will be shown only in the monitor that supports these functions. The tone of the color can be changed.
well as pictures taken by a digital camera or scanner through Windows. 6-Color z z z Saturation - To adjust the chroma. Hue - To adjust the color tone. Reset - To reset the monitor settings to the factory defaults. Image Tab Definition Adjusts the Fine , Coarse and Position values. z Image Setup z z Fine : Removes noise such as horizontal stripes. If the noise persists even after Fine tuning, repeat it after adjusting the frequency (clock speed). Coarse : Removes noise such as vertical stripes.
Support Tab Definition Shows the Asset ID and the version number of the program, and allows you to use the Help feature. Help Visit the MagicTune website or click to open the Help files (User Manual) if you need any help installing or running MagicTune. The User Manual opens within a basic browser window. Asset ID You can use the server to control the Client monitor. (Server program should be installed to use this program as Client) Version User Name Shows the user name that is registered in PC.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Color Calibration 1. Color Calibration Color Calibration guides you to get optimal color condition for your monitor. Proceed following 5steps for getting optimal monitor color condition . 1. 2. 3. 4. 5.
2. Press "View Uncalibrated" button to see the original image.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Uninstall The MagicTune™ program can be removed only by using the "Add or Remove Programs" option of the Windows™ Control Panel. Perform the following steps remove MagicTune™. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add or Remove Programs" icon in Control Panel. 3.
Overview | Installation | OSD Mode | Color Calibration | Uninstall | Troubleshooting Troubleshooting The current computing system is not compatible with MagicTune™. Please press OK and click on the "Shortcut to the MagicTune™ site" to view our home page for further reference. An error may occur when your video/graphic card is not in the 'Available' list. (The latest or oldest video cards may not be compatible.) Please visit our homepage to see the Troubleshooting section.
Visit the video card maker's homepage and download and install the latest driver. For more information about the video card, contact the card manufacturer. To ensure normal operation, please restart your system. An error occurs when the system is not restarted after installing MagicTune™. (This is for Win98SE and WinMe only.) Restart the system before use. For the best performance of MagicTune™, adjust to the optimal resolution. Refer to the User Guide for the optimal resolution.
the graphic card, visit our website to check the compatible graphic card list provided. http://www.samsung.com/monitor/MagicTune MagicTune™ doesn't work properly. z z Have you changed your PC or video graphic card? Download the latest program. The program can be downloaded http://www.samsung.com/monitor/MagicTune. Visit the MagicTune™ website for technical support for MagicTune™, FAQs (questions and answers) and software upgrades.
Overview | Installation | Interface | Uninstall | Troubleshooting Overview What is MagicRotation? Traditionally, computer displays allowed the user to view only in landscape mode. In today's information age, more users need to view documents, web pages, emails, etc. in there day to day life. These types of applications can be better viewed in portrait mode where the entire contents are available on the screen.
3. Select installation Language, Click "Next". 4. When the InstallShield Wizard window appears, click "Next." 5. Select "I accept the terms of the license agreement" to accept the terms of use. 6. Choose a folder to install the MagicRotation program.
7. Click "Install." 8. The "Setup Status" window appears. 9. Click "Finish." Have to reboot the system in order for the MagicRotation to work properly.
10. When the installation is complete, the MagicRotation executable icon appears on your desktop. Installation Problems The installation of MagicRotation can be affected by the factors such as video card, motherboard and the network environment. See "Troubleshooting" if you have trouble during installation. Limitation 1. The "Display Driver" should be properly loaded for the MagicRotation to work properly. The installed "Display Driver" should be the latest driver supplied by the vendor. 2.
z z Windows™ XP Home Edition Windows™ XP Professional Hardware z z 128MB Memory above(recommended) 25MB Free Hard disk space above Service Packs z z It is recommended that your System has the latest Service Pack installed. For Windows™ NT 4.0, it is recommended to install Internet Explorer 5.0 and above with Active Desktop component. * For more information, visit the MagicRotation website. * Windows™ is registered trademark of Microsoft Corporation,Inc.
Rotate : Display will get rotated by the unit of 90 degree. Rotate to 0 : Display will get rotated to 0 degree from the current angle of Rotation. Rotate to 90 : Display will be rotated 90 degrees from the current angle.
Rotate to 180 : Display will be rotated 180 degrees from the current angle. Rotate to 270 : Display will be rotated 270 degrees from the current angle. Hot key : Hot Keys are available by default and can be changed by user. It can be assigned by user directly with keyboard after changing the existing HotKey . User can create the hot key with the combination of Shift, Ctrl, Alt and general keys. In case only general key is pressed, it will be assigned in the form of Alt+general key.
Overview | Installation | Interface | Uninstall | Troubleshooting Uninstall The MagicRotation program can be removed only by using the "Add/Remove Programs" option of the Windows Control Panel. Perform the following steps to remove MagicRotation. 1. Go to [Task Tray] ' [Start] ' [Settings] and select [Control Panel] in the menu. If the program runs on Windows™ XP, go to [Control Panel] in the [Start] menu. 2. Click the "Add/Remove Programs" icon in Control Panel. 3.
3. Check if the problem occurs without installing MagicRotation Software. If the problem is repeating in any/all of the following scenarios then it may be the problem with your installed "Display Driver" : In order to correct the problem you need to perform the following steps : 1. Uninstall MagicRotation Software. 2. Obtain the latest "Display Driver" from your Graphic Card Vendor. The latest "Display Driver" from (ATI, NVIDIA, MATROX, INTEL, etc.
Before calling for service, check the information in this section to see if you can remedy any problems yourself. If you do need assistance, please call the phone number on the Information section or contact your dealer. Symptom No images on the screen. I cannot turn on the monitor. Check List Solutions Is the power cord connected properly? Check the power cord connection and supply. Can you see "Check Signal Cable" on the screen? (When connecting D-sub cable) Check the signal cable connection.
There is no image on the screen. Is the power indicator on the monitor blinking at 1 second intervals? The monitor is in PowerSaver mode. Press any key on the keyboard to activate the monitor and restore the image on the screen. If there is still no image, press the 'SOURCE' button. Then press any key on the keyboard again to activate the monitor and restore the image on the screen.
DDC) function can be supported. Check when MagicTune™ does not function properly. MagicTune™ feature is found only on PC (VGA) with Window OS that supports Plug and Play. * To check whether your PC is available for MagicTune™ feature, follow the steps below (When Windows is XP); Control Panel -> Performance and Maintenance > System -> Hardware -> Device Manager -> Monitors -> After deleting Plug and Play monitor, find 'Plug and Play monitor' by searching new Hardware.
Do not allow any water to go inside the monitor. Self-Test Feature Check Self-Test Feature Check | Warning Messages | Environment | Useful Tips Your monitor provides a self test feature that allows you to check whether your monitor is functioning properly. 1. Self-Test Feature Check 1. Turn off both your computer and the monitor. 2. Unplug the video cable from the back of the computer. 3. Turn on the monitor. If the monitor is functioning properly, you will see a box in the illustration below.
then contact the Service Center or your dealer. z Judging the monitor's working condition If there is no image on the screen or a "Not Optimum Mode","Recommended Mode : 1600 X 1200 60Hz" message comes up, disconnect the cable from the computer while the monitor is still powered on. { If there is a message coming up on the screen or if the screen goes white, this means the monitor is in working condition. { In this case, check the computer for trouble.
General General Model Name SyncMaster 214T LCD Panel Size 21.3" Diagonal (54 cm) Display area 432 mm (H) x 324 mm (V) Pixel Pitch 0.270 mm (H) x 0.270 mm (V) Type a-si TFT/SPVA Synchronization Horizontal 30 ~ 81 kHz Vertical 56 ~ 75 Hz Display Color 16.7M Colors Resolution Optimum resolution 1600 x 1200 @ 60 Hz Maximum resolution 1600 x 1200 @ 60 Hz (Analog) 1600 x 1200 @ 60 Hz (Digital) Input Signal, Terminated Analog RGB, DVI Compliant Digital RGB, CVBS, S-Video Composite Sync,SOG, 0.
15pin-to-15pin D-sub cable, detachable, 1.8 m DVI-D to DVI-D connector, detachable, 2.0m Power Consumption Less than 63W(Analog/Digital) Dimensions (WxDxH)/ Weight 469.0 x 228.5 x 466.2mm (18.5 x 9.0 x 18.4 inch) / 8.8 kg (state of stand installed) VESA Mounting Interface 100 mm x 100 mm (for use with Specialty(Arm) Mounting hardware.
Preset Timing Modes If the signal transferred from the computer is the same as the following Preset Timing Modes, the screen will be adjusted automatically. However, if the signal differs, the screen may go blank while the power LED is on. Refer to the video card manual and adjust the screen as follows. Table 1. Preset Timing Modes Horizontal Frequency (kHz) Vertical Frequency ( Hz) Pixel Clock (MHz) Sync Polarity (H/V) IBM, 640 x 350 31.469 70.086 25.175 +/- IBM, 720 x 400 31.469 70.087 28.
Contact SAMSUNG WORLD-WIDE If you have any questions or comments relating to Samsung products, please contact the SAMSUNG customer care center. North America CANADA 1-800-SAMSUNG (7267864) http://www.samsung.com/ca MEXICO 01-800-SAMSUNG (7267864) http://www.samsung.com/mx U.S.A 1-800-SAMSUNG (7267864) http://www.samsung.com Latin America ARGENTINE 0800-333-3733 http://www.samsung.com/ar BRAZIL 0800-124-421 http://www.samsung.com/br CHILE 800-726-7864 (SAMSUNG) http://www.samsung.
CZECH REPUBLIC 844 000 844 http://www.samsung.com/cz DENMARK 38 322 887 http://www.samsung.com/dk FINLAND 09 693 79 554 http://www.samsung.com/fi FRANCE 08 25 08 65 65 (€ 0,15/min) http://www.samsung.com/fr GERMANY 01805 - 121213 (€ 0,12/Min) http://www.samsung.de HUNGARY 06 40 985 985 http://www.samsung.com/hu ITALIA 199 153 153 http://www.samsung.com/it LUXEMBURG 02 261 03 710 http://www.samsung.lu NETHERLANDS 0900 20 200 88 (€ 0.10/Min) http://www.samsung.
Terms Dot Pitch The image on a monitor is composed of red, green and blue dots. The closer the dots, the higher the resolution. The distance between two dots of the same color is called the 'Dot Pitch'. Unit: mm Vertical Frequency The screen must be redrawn several times per second in order to create and display an image for the user. The frequency of this repetition per second is called Vertical Frequency or Refresh Rate.
{ { Resolution: 1600 X 1200 Vertical frequency (refresh rate): 60 Hz 2. TFT LCD panel manufactured by using advanced semiconductor technology with precision of 1ppm (one millionth) above is used for this product. But the pixels of RED, GREEN, BLUE and WHITE color seem to be bright sometimes or some of black pixels could be seen. This is not from bad quality and you can use it without uneasiness. { For example, the number of TFT LCD sub pixels that is contained in this product are 5,760,000. 3.
MÉXICO IMPORTADO POR: SAMSUNG ELECTRONICS MÉXICO. S.A. de C.V. Vía Lopez Portillo No. 6, Col. San Fco. Chilpan Tultitlán, Estado de México, C.P. 54940 Tel: 01-55-5747-5100 / 01-800-726-7864 EXPORTADO POR: Samsung Electronics CO.,LTD.
PRODUCT INFORMATION (Image Retention Free) LCD Monitors and TVs may have image retention when switching from one image to another especially after displaying a stationary image for a long time. This guide is to demonstrate correct usage of LCD products in order to protect them from Image retention. Warranty Warranty does not cover any damage caused by image retention. Burn-in is not covered by the warranty.
Ex) The best way to protect your monitor from Image retention is to set your PC or System to operate a Screen Saver program when you are not using it. Image retention may not occur when a LCD panel is operated under normal conditions. Normal conditions are defined as continuously changing video patterns. When the LCD panel is operated for a long time with a fixed pattern (-over 12 hours-), there may be slight difference in voltage between electrodes that work the liquid crystal (LC) in a pixel.
Correct Disposal of This Product (Waste Electrical & Electronic Equipment) - Europe only (Applicable in the European Union and other European countries with separate collection systems) This marking shown on the product or its literature, indicates that it should not be disposed with other household wastes at the end of its working life.
