User Manual
Table Of Contents
- WF6300B_SimpleUX_UM_DC68-04355A-01_EN
- WF6300B_SimpleUX_UM_DC68-04355A-01_CFR
- Consignes de sécurité
- Remarques importantes sur les consignes de sécurité
- Symboles de sécurité importants
- Consignes de sécurité importantes
- AVERTISSEMENT CONCERNANT LA PROPOSITION 65 DE L'ÉTAT DE CALIFORNIE
- Avertissements importants concernant l'installation
- Mises en garde pour l'installation
- Avertissements importants concernant l'utilisation
- Mises en garde concernant l'utilisation
- Avertissements importants concernant le nettoyage
- Notification de réglementation
- Installation
- Avant de démarrer
- Opérations
- Maintenance
- Dépannage
- Caractéristiques techniques
- Consignes de sécurité
- WF6300B_SimpleUX_UM_DC68-04355A-01_MES
- Información sobre seguridad
- Lo que necesita saber sobre las instrucciones de seguridad
- Símbolos de seguridad importantes
- Precauciones de seguridad importantes
- PROPOSICIÓN 65 DE CALIFORNIA: ADVERTENCIA
- Advertencias fundamentales para la instalación
- Precauciones para la instalación
- Advertencias fundamentales para el uso
- Precauciones de uso
- Advertencias fundamentales para la limpieza
- Aviso regulatorio
- Instalación
- Antes de comenzar
- Funcionamiento
- Mantenimiento
- Solución de problemas
- Especificaciones
- Información sobre seguridad
English
English 53
Problem Action
Fills with the wrong
temperature water.
• Fully open both taps.
• Make sure the temperature selection is correct.
• Make sure the hoses are connected to the correct taps. Flush water lines.
• Make sure your water heater is set to supply hot water with a minimum
temperature of 120 °F (49 °C) at the tap. Also, check the water heater
capacity and recovery rate.
• Disconnect the hoses and clean the mesh filters. The mesh filters may be
clogged.
• While the washer fills, the water temperature may change as the
automatic temperature control feature checks incoming water
temperature. This is normal.
• While the washer fills, you may notice just hot and/or just cold water
going through the dispenser when cold or warm temperatures are
selected. This is a normal function of the automatic temperature control
feature as the washer determines the water temperature.
The load is wet at the
end of a cycle.
• Use the High or Extra High spin speed.
• Use high efficiency (HE) detergent to reduce oversudsing.
• The load is too small. Small loads (one or two items) may become
unbalanced and not spin completely.
• Make sure the drain hose is not kinked or clogged.
• Make sure the pump filter is not clogged.
Leaks water.
• Make sure the door is properly closed.
• Make sure all hose connections are tight.
• Make sure the end of the drain hose is correctly inserted and secured to
the drain system.
Reference Installation: Step-by-step installation in this user manual.
• Avoid overloading.
• Use high efficiency (HE) detergent to prevent oversudsing.
• Make sure the pump filter is not clogged.
• Clean the door seal (diaphragm).
• Clean the detergent drawer. Close detergent drawer completely.
Has odors.
• Excessive suds collect in recesses and can cause foul odors.
• Run SELF CLEAN cycles every 40 cycles to sanitize periodically.
• Clean the door seal (diaphragm).
• Dry the washer interior after a cycle has finished by leaving the door
open.
• Make sure the pump filter is not clogged.
• Make sure the end of the drain hose is correctly inserted and secured to
the drain system.
Reference Installation: Step-by-step installation in this user manual.
Untitled-5 53 2022-01-20 5:06:28