User Manual

setup screen
30_ setup screen
User
1. From the Setup menu, select the <Basic ( )> tab.
2. Click <User>.
3. Provide the necessary user information.
• Administrator password change : Change the password
for the administrator.
J
`
For the security purposes, you are recommended to use a
combination of numbers, alphabets uppercase and lowercase
and special characters for your password.
`
It is recommended to change your password once every three
months.
`
The password length and limits are shown as follows.
-
A combination of at least three types of upper case, lower case, numeric, and special characters: 8 to 9 characters.
-
A combination of at least two types of upper case, lower case, numeric, and special characters: 10 to 15 characters.
-
Should be different from the ID.
-
Cannot repeat the same letter, number of special characters more than 4 times.
-
Don’t use 4 or more characters consecutive together. (examples : 1234, abcd)
-
Don’t use 4 or more characters repeated. (examples : !!!!, 1111, aaaa)
-
Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/
-
After the factory setting, the admin and user passwords are initialized. You need to reset the password.
-
When you access the camera web page for the first time or access it after the initialization, you will be moved to the
admin password setting menu.
-
In this menu, you need to login again with the new password before using the camera web page menus.
-
If the existing password is not matched, when you change the admin password, you cannot change the password.
-
After changing your password, if there is a camera connected to a CMS or NVR client, then you need to re-register it
with the newly changed password. If the camera is still connected with the same password, then the account may be
locked because a client uses the previous password.
`
If you try to login with the registered account, 5 or more consecutive password authentication has failed, and then the
account may be locked for thirty seconds.
`
When the password is changed while multiple connections are active from a PC, the browser may malfunction. In that
case, reconnect to the server.
• Guest setup : If you select <Enable guest access>, the guest account can access the Web viewer
screen but can only view the live Viewer screen.
`
The ID/password for the guest account is <guest/guest>, which cannot be changed.
• Authentication setup : If you select <Enable RTSP connection without authentication>, you can
access RTSP without logging in and view the video.
To Use Crop Encoding
1. Select <Enable>.
2. Click <Set area>.
The Crop Encoding Area Setup window will pop up.
• 16:9 : The aspect ratio shall be set to 16:9 as close as to
the user specified area.
The supporting size ranges from 640X360 to 1280X720
and supporting output resolutions are 640X360, 800X448,
1280X720.
• 4:3 : The aspect ratio shall be set to 4:3 as close as to the
user specified area.
The supporting size ranges from 320X240 to 1280X960
and supporting output resolutions are 320X240, 640X480,
800X600, 1024X768, and 1280X960.
• Manual : It sets up the aspect ratio of the user specified
area.
The supporting size ranges from XNB-6000: 320X240 ~ 1280X1024 / XNB-8000: 320x240 ~
1600x1200 and all supporting output resolutions are available except 1920X1080.
3. Drag the mouse on the screen to specify the Crop Encoding area at your discretion.
J
`
If you set output as <Manual>, you can specify a desired range. However, if output is only available at a supported resolution,
the image will be output at the resolution that is closest to the range that you specified.
`
The Crop Encoding area setup can change depending on the DIS setup. Reset the Crop Encoding area when the DIS setup is
changed.