User Manual

setup screen
44_ setup screen
• E-mail configuration
- Server address : Enter the SMTP address of the email server that you transfer the alarm or event
images to.
- Authentication : Select whether to use authorization.
- TLS : Specify the use of TLS.
- ID : Enter the user ID for logging into the email server.
- Password : Enter the user account password for logging into the email server.
- Port : The default port of the email server is 25; however, you can use a different port number
according to the email server settings.
- Recipient : Enter the address of the email recipient.
- Sender : Enter the address of the email sender. If the sender address is incorrect, the email from the
sender may be classified as SPAM by the email server and thus may not be sent.
- Subject : Enter a subject for your email.
- Body : Provide the text for the massage. Attach the alarm or event images to the email that you are
preparing.
4. When done, click [Apply].
Storage
You can activate recording on your device, set the recording conditions, check the saved data capacity and
format the device itself.
1. From the Setup menu, select the <Event (
)> tab.
2. Click <Storage>.
3. Select a device to save data in.
M
`
If your device is properly recording data, it will display “Recording”.
`
If you see an “Error” message, check the following:
-
Check the storage to see if it is connected to the device.
-
Check the files in the storage to see if they are damaged.
-
Check the storage to see if they are physically damaged.
`
If the “Error” message does not disappear after following the instructions, format the Micro SD card.
After formatting, if the error message still remains, replace the Micro SD card.
`
If you remove the Micro SD card without changing a button to ‘off’ position in settings or if you connect a camera to an
unstable power source, the Micro SD card may be damaged.
J
`
The number of simultaneously accessible new profiles after the recording mode is activated is 2.
To make recording on the Micro SD memory
1. Set the SD card unit to <On>.
2. Click the [Apply] button.
3. Check the memory card’s <Free size> and <Total size>.
You can format the Micro SD card by clicking the <Format> button.
`
Some frames may be skipped if the Micro SD memory card operates at the lower speed than recommended.
For more details, refer to “Recommended Micro SD/SDHC/SDXC Memory Card Specifications”. (Page 6)
`
For a Micro SD memory card with a large capacity, the formatting will be slowed down accordingly.
`
The data traffic will increase when the camera is set to higher resolution, higher bit rate, and/or higher framerate.
If there is too much data traffic, some frame may be skipped although it is stored in a full frame.
`
When a frame skip occurs, images are saved at the rate of min. one image per sec.
4. Specify the storage action.
• Record profile : The name of profile to be recorded is displayed.
• Normal recording : Make recording at a certain frame rate.
• Event recording : Set the recording type for a certain event that occurs.
• Pre event duration : Specify the time point before the occurrence of the alarm; starting from the time
point, the images will be transferred. You can specify up to 5 seconds before the occurrence of the
alarm.
• Post event duration : Specify the time point after the occurrence of the alarm; to the specified time
point, the images will be transferred. You can specify up to 120 seconds after the occurrence of the
alarm.
• Record file type : It specifies the file format of the recorded images.
- STW : It is Hanwha Techwin’s unique file format.
- AVI : It is the conventional avi format.
J
`
If the Record file type is changed, the existing data is formatted.
• Overwrite : If the Micro SD memory is full, this will delete old data and store new data in replacement.
• Auto delete : Data for a certain period is deleted, while other data is not deleted.
This can be set within the range of one day to 180 days.
J
`
If the storage period is expired, data is automatically deleted and new data will be recorded. Once deleted, it cannot be
recovered.
5. Set <SD File System>.
• Type : Camera supports VFAT and ext4 as an SD card file system, which can be configured by the user.
(However, in case of ext4 file system, an additional application is required to recognize the Windows
operating system)
J
`
If the settings are changed, the existing data will be formatted.
`
It may take up to 10 minutes to format an SD card in the ext4 file system.
6. Specify the <Normal record schedule>.
• Always : Always save recorded video in the Micro SD memory card.
`
If set to Always, the activation time cannot be changed.
• Only scheduled time :
Records only on the specified time of the specified day of week.
7. When done, click [Apply].