NETWORK CAMERA User Manual XNV-6081Z/XNV-8081Z XND-6081VZ/XND-8081VZ XND-6081FZ/XND-8081FZ
Network Camera User Manual Copyright ©2018 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview Important Safety Instructions 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. The battery cannot be replaced. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS overview Outdoor Vandal Dome 8 Indoor Vandal Dome 17 6 Important Safety Instructions Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs 8 8 9 What’s Included At a Glance Installation 17 17 18 What’s Included At a Glance Installation Flush Mount Dome 25 25 26 What’s Included At a Glance Installation installation & connection 32 33 Optional Accessories for Installation Connecting with other Device 25 32 37 37 37 38 38 40 4
overview Recommended PC Specifications NAS recommended specs •• CPU : Intel(R) Core(TM) i7 3.4 GHz or higher •• RAM : 8G or higher •• Supported OS : MS Windows, Mac OS X •• Recommended browser: Google Chrome Supported browsers: MS Explorer, MS Edge, Mozilla Firefox (Window 64bit only), Apple Safari (Mac OSX only) •• Recommended capacity : 200GB or higher is recommended. •• Simultaneous access : One unit of NAS can accept a maximum of sixteen camera accesses.
XNV-6081Z/XNV-8081Z 8 Indoor Vandal Dome XND-6081VZ/XND-8081VZ 17 ●● overview Outdoor Vandal Dome Flush Mount Dome XND-6081FZ/XND-8081FZ 25 English _7
What’s Included As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
Installation J 2. Peel off the tape attached to the camera module. ` This camera is waterproof and in compliance with the IP6K9K / IP67 / IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
outdoor vandal dome Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installing the AC module (sold separately: SPC-100AC) 1. Install the AC module as shown in the figure. 2. Tighten the screw using the hex key. 1x JJ `` Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
Installation (mount plate) [Directly installing on wall/ceiling] [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● Outdoor Vandal Dome 2-2. Separate the pipe cover of the mount plate by pressing its sides. 1-2. Fix the mount plate using appropriate screws. 1-3.
outdoor vandal dome 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 1-4. Mount the bush to the camera case. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected. -- Camera main: use a cable with the diameter of Ø5 to 6.5 -- Components: use a cable with the diameter of Ø5 to 8.5 [Installing LAN/power cables] 1-1.
2-3. Mount the bush to the camera case. 4. Join the mount plate with the camera case. ●● Outdoor Vandal Dome 2x x4 TR20 [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case.
outdoor vandal dome Installing the camera module 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. Assembling the dome cover [Directly installing on wall/ceiling] 1. Assemble the dome cover. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue.
Using/Removing Skin cover [Using Weather cap] 1. Remove the screws from the dome cover. 1. Put on the skin cover in alignment with the pipe cover. ●● Outdoor Vandal Dome 2x TR20 2. Assemble the dome cover. 3. Mount the weather cap to the dome cover and fasten the screws. JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 2. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on.
outdoor vandal dome 3. To remove the skin cover, pull it while turning it clockwise as shown in the figure. JJ `` Repetitive installation and removal of the skin cover may deform the skin cover. `` Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.
What’s Included a Pipe-cover As for each sales country, accessories are not the same. of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power h Micro USB terminal of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the the powerBe ware ofCAUTION: and Polarity Rated Voltageconnection.
indoor vandal dome Installation 2. Peel off the tape attached to the camera module. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installation (mount plate) [Directly installing on wall/ceiling] 1-1. Attach the installation template on the desired surface and drill holes for screws and cables. ●● Indoor Vandal Dome JJ `` Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
indoor vandal dome [Installing using pipe] 2-1. Attach the installation template and drill holes for screws and cables. 2-2. Separate the pipe cover of the mount plate by pressing its sides. 2-3. Place the pipe on the mount plate. 2-4. Fix the mount plate using appropriate screws. 2-5. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe. Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected.
1-4. Mount the bush to the camera case. 2-3. Mount the bush to the camera case. ●● Indoor Vandal Dome [Installing the LAN cable] 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable.
indoor vandal dome Installing the camera module [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case. 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. 3. Connect the microphone cable to the camera module. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 4.
Assembling the dome cover Using/Removing Skin cover 1. Put on the skin cover in alignment with the pipe cover. [Directly installing on wall/ceiling] 1. Assemble the dome cover. ●● Indoor Vandal Dome JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 4x x4 TR20 2. For a camera connected with a pipe, remove the pipe cover from the skin cover first before putting it on.
indoor vandal dome 3. To remove the skin cover, pull it while turning it clockwise as shown in the figure. JJ `` Repetitive installation and removal of the skin cover may deform the skin cover. `` Installation and removal of the skin cover with excessive force may cause scratches on the surface of the product.
At a Glance flush mount dome What’s Included a Bracket As for each sales country, accessories are not the same. d Dome-cover of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power h Reset button of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power of the Be ware CAUTION: and Polarity Rated Voltageconnection.
flush mount dome Installation 2. Peel off the tape attached to the camera module. camera is waterproof and in compliance with the IP52 spec, but the jack connected to the external cable is not. You are JJ `` This recommended to install this product below the edge of eaves to prevent the cable from being externally exposed.
Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot. Installation (housing) 1. Attach the installation template to the ceiling and mark its location with a pencil. ●● Flush Mount Dome JJ `` Please note that if you firmly push and release the Micro SD memory card when it is ejected, it may pop out.
flush mount dome 3. Connect the safety cable. JJ `` A safety cable is not provided. e.g. [Using pipe] 4-1. Install the pipe in a fitting hole. ¾” NUT ½” NUT 28_ flush mount dome 4-2. Pull out necessary cables among LAN/power/audio & alarm cables through the pipe.
Installation (camera case) JJ `` Use a cable bush compliant with the LAN cable to be connected. -- Components: use a cable with the diameter of Ø5 to 8.5 2-1. Pull off the extruded part of the 1-hole bush provided. 2-2. Use the cap installer to pass through the RJ45 cable. Cap Installer ●● Flush Mount Dome [Installing LAN/power cables] [Installing the LAN cable] 1-1. Pull off the extruded parts of the bush to be used. 1-2.
flush mount dome [Installing audio & alarm cables] 3-1. Mount the bush of the provided audio & alarm cables to the camera case. Installing the camera module 1. Connect the LAN/power/audio & alarm cables to the camera module terminal. 2. Attach the camera module to the case. JJ `` A magnet is embedded at the bottom of the module `` Take caution not to allow any foreign objects between the attaching surfaces. 4. Turn the screws on the housing to fix the housing to the ceiling.
Assembling the dome cover Outdoor installation JJ `` Make sure to firmly tighten the fastening screws so that there is no water damage issue. 1. Connect the power, I/O, and LAN cables. 1. Assemble the dome cover. 2. Wrap the black cable jacket (Area A) and the cable connection area with waterproof (butyl rubber) tape so that more than half of the butyl rubber tape is overlapped.
of the Be ware CAUTION: and Polarity Rated Voltageconnection. of the power installation & connection Optional Accessories for Installation You can purchase appropriate optional accessories available.
Connecting with other Device Adjusting the monitoring direction for the camera WiFi dongle Tilt ●● installation & connection SOFT AP Pan * AC Lens rotation `` Adjusting the monitoring direction You can adjust the camera direction only when the camera is fixed on the ceiling. At this time, rotating the main body of the camera in the left and right direction is called PAN, and adjusting the angle of the camera is called TILT. -- The effective range of pan is a total of ±175˚ degrees.
installation & connection Ethernet Connection Connect the Ethernet cable to the local network or to the Internet. Connecting WiFi Camera Setup 1. Connect OTG adapter (5-pin) and WiFi dongle to the micro USB terminal. Smartphone Setup 3. Run the Wisenet Installation application. 4. When you log in to the camera, the video will be connected. `` The video will be played without being logged in during the initial connection. 5. You can adjust angle of view while watching the video through smartphone.
Connecting to Audio Input/Output •• Audio Codec PC Speaker Network Microphone Speaker Amp Amp Microphone Speaker 1. Connect the AUDIO IN port of the camera with the microphone or LINE OUT port of the amplifier that the microphone is connected to. can use the internal microphone of the camera without an external microphone connection MM `` You (only applicable for XND-6081VZ/XND-8081VZ). 2.
installation & connection Connecting to the I/O port box Alarm In Wiring Diagram Connect the Alarm I/O cable to the corresponding port of the port box. External connection Inside of the camera VCC_3.3V RESISTOR Sensor ALARM IN (5mA SINK) RESISTOR RESISTOR MLCC GND DIODE TRANSISTOR GND Alarm Out Wiring Diagram Warning lamp / Siren power (-) Sensor •• ALARM-IN : Used to connect the alarm input sensor. •• ALARM-OUT : Used to connect the alarm output signal.
network connection and setup You can set up the network settings according to your network configurations. Connecting the Camera Directly to Local Area Networking Connecting the Camera Directly to a DHCP Based DSL/Cable Modem INTERNET 1. Launch an Internet browser on the local PC. DSL/Cable Modem 2. Enter the IP address of the camera in the address bar of the browser. External Remote PC Camera DDNS Server (Data Center, KOREA) Camera 1. Connect the user PC directly with the network camera.
network connection and setup Buttons used in IP Installer a b c d Item e f g Description Scans for cameras with the IPv6 setting. Activated in an IPv6 compliant environment only. i IPv6 j Search Scans for cameras that are currently connected to the network. However, this button will be grayed out if neither IPv4 nor IPv6 is checked. k l m Auto Set The IP Installer automatically configures the network settings. Manual Set You should configure the network settings manually.
If not using a Broadband Router If the Broadband Router has more than one camera connected 4. In the pane, provide necessary information. •• HTTP Port : Used to access the camera using the Internet browser, defaulted to 80. •• VNP Port : Used to control the video signal transfer, defaulted to 4520. ex) For setting , , and , contact your network administrator.
network connection and setup Dynamic IP Setup Dynamic IP Environment Setup •• Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server 3. When done, click [Save Settings]. Your settings will be saved. MM `` Above sample instructions are based on the CISCO’s Broadband Router. `` The settings may differ depending on the connected Broadband Router model. For more information, refer to the user manual of the applicable router.
Connecting to the Camera from a Shared Local PC 1. Run the IP Installer. It will scan for connected cameras and display them as a list. ●● network connection and setup 2. Double-click a camera to access. The Internet browser starts and connects to the camera. to the camera can also be gained by typing the camera’s IP MM `` Access address in the address bar of the Internet browser.
web viewer Connecting to the Camera Normally, you would 1. Launch the Internet browser. 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2.
Password setting a new password with 8 to 9 digits, you must use at least 3 of JJ `` For the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].?/ 1. Click the [Setup ( )] icon. 2. The Settings window appears. 3.
appendix Specification Items 1/2.8” 2M CMOS Effective Pixels 1945(H) x 1097(V) 2.13M Total Pixels Video Scanning System Min. Illumination S / N Ratio Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Angular Field of View Lens Min.
Items Ethernet Resolution Max. Framerate Smart Codec WiseStream Video Quality Adjustment Bitrate Control Method Network Streaming Capability XND-6081VZ Items XND-6081FZ Max. User Access H.265/H.264 (MPEG-4 Part 10/AVC) : Main/Baseline/High Motion JPEG Edge Storage 1920x1080, 1280x1024, 1280x960, 1280x720, 1024x768, 800x600, 800x448, 720x576, 720x480, 640x480, 640x360, 320x240 H.264/H.
appendix Items 1/1.8” 6M CMOS Effective Pixels 2616(H) x 1976(V) Total Pixels Video Scanning System Min. Illumination S / N Ratio Video Out Focal Length (Zoom Ratio) Max. Aperture Ratio Angular Field of View Lens Min.
Items Ethernet Resolution Max. Framerate Smart Codec WiseStream Video Quality Adjustment Bitrate Control Method Network Streaming Capability XND-8081VZ Items XND-8081FZ Max. User Access H.265/H.264 (MPEG-4 Part 10/AVC) : Main/Baseline/High Motion JPEG Edge Storage 2560x1920, 2560x1440, 1920x1080, 1600x1200, 1280x1024, 1280x960, 1280x720, 1024x768, 800x600, 800x448, 720x576, 720x480, 640x480, 640x360, 320x240 H.264/H.
appendix Product Overview XNV-6081Z/XNV-8081Z 48_ appendix XND-6081VZ/XND-8081VZ Unit : mm (inch) Unit : mm (inch)
XND-6081FZ/XND-8081FZ Unit : mm (inch) Troubleshooting PROBLEM What are the specifications for WAVE files necessary to play audio at the time of an event? No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. yy This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver. yy Sampling rate of 48,000 KHz or less is recommended.
appendix PROBLEM SOLUTION No image appears. yy If the transmission method is set to multicast, check whether there is a router that supports multicast in the LAN the camera is connected to. Voice is not recorded even though audio input settings are configured. yy You must enable the
Open Source Announcement GPL/LGPL software license If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. Component Name License Base Kernel Busybox iproute2-4.3.0 iptables-1.4.21 ethtool-4.2 mtd-1.5.2 mii-diag-2.11 rp-pppoe-3.11 wpa_supplicant-2.5 bash-4.3.30 zeroconf GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 3.0 GPL 2.
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice.
provides that the language of a contract shall be construed against the drafter shall not apply to this License. 12. RESPONSIBILITY FOR CLAIMS. As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary Code thereof. 17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the Source Code or the Binary Code thereof. 18. "Source Code User" means a person who uses the Source Code. 19.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
PHP 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. Component Name License URL php-5.2.17 PHP 3.01 http://www.php.net/distributions Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwhasecurity.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.eu User Manual ver.
