NETWORK CAMERA User Manual XNV-6080RSA/XNV-8080RSA/XNV-6120RSA
Network Camera User Manual Copyright ©2018 Hanwha Techwin Co., Ltd. All rights reserved. Trademark Each of trademarks herein is registered. The name of this product and other trademarks mentioned in this manual are the registered trademark of their respective company. Restriction Copyright of this document is reserved. Under no circumstances, this document shall be reproduced, distributed or changed, partially or wholly, without formal authorization.
overview IMPORTANT SAFETY INSTRUCTIONS 1. Read these instructions. 2. Keep these instructions. 4. Follow all instructions. 5. Do not use this apparatus near water. 6. Clean the contaminated area on the product surface with a soft, dry cloth or a damp cloth. (Do not use a detergent or cosmetic products that contain alcohol, solvents or surfactants or oil constituents as they may deform or cause damage to the product.) 7.
overview Class construction An apparatus with CLASS construction shall be connected to a MAINS socket outlet with a protective earthing connection. Battery Batteries(battery pack or batteries installed) shall not be exposed to excessive heat such as sunshine, fire or the like. Disconnection Device Disconnect the main plug from the apparatus, if it’s defected. And please call a repair man in your location. When used outside of the U.S.
CONTENTS OVERVIEW INSTALLATION & CONNECTION 12 NETWORK CONNECTION AND SETUP 19 6 7 8 10 12 15 16 19 19 20 20 21 21 21 22 22 23 24 24 Important Safety Instructions Product Features Recommended PC Specifications Recommended Micro SD/SDHC/SDXC Memory Card Specifications NAS recommended specs What’s Included At a Glance (XNV-6080RSA/XNV-8080RSA) At a Glance (XNV-6120RSA) Installation Inserting/Removing a Micro SD Memory Card Connecting with other Device WEB VIEWER 25 APPENDIX 28 25 26 26 26 27 27
overview PRODUCT FEATURES •• Material : stainless steel The exterior of the camera is made of stainless steel, which can be installed in various special environments due to its corrosion prevention properties and ease of handling. •• Dustproof/Waterproof The dustproof/waterproof design protects the product from rain and dust when installed outdoors.
WHAT’S INCLUDED Please check if your camera and accessories are all included in the product package. (As for each sales country, accessories are not the same.) + 24V / DC T 12V F N 1 Quick Guide (Optional) 1 Warranty card (Optional) 1 Cable for the testing monitor 1 AF VIDEO Camera Description W RESET Quantity Mount plate 1 Appearance of the Be ware CAUTION: and Polarity Rated Voltageconnection.
overview AT A GLANCE (XNV-6080RSA/XNV-8080RSA) Components Appearance ab c d e RESET VIDEO A DC C 2 12 4V V LINK - b 12 V T DC ACT V/ USB NETWORK + 24 AUDIO ALARM AC N T W F AF a F N W T AF RESE VID EO f g h Item Description a Dome cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body.
Item Illumination Sensor Detects incoming light to control the IR LED. b Lens Lens for the camera. d e IR LED Reset Button Zoom/Focus Control Button These infrared LED’s are controlled by the illumination sensor. j Audio and alarm cable port The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled.
overview AT A GLANCE (XNV-6120RSA) Components Appearance ab c d e RESET VIDEO A DC C 2 12 4V V LINK - b 12 V T DC ACT V/ USB NETWORK + 24 AUDIO ALARM AC N T W F AF a F N W T AF RESE VID EO f g h Item Description a Dome cover Case cover used to protect the lens and the main unit. b Camera Case Housing part that covers the camera body.
Item Illumination Sensor Detects incoming light to control the IR LED. b Lens Lens for the camera. d e IR LED Reset Button Zoom/Focus Control Button These infrared LED’s are controlled by the illumination sensor. j Audio and alarm cable port The button restores all camera settings to the factory default. Press and hold for about 5 seconds to reboot the system. J If you reset the camera, the network settings will be adjusted so that DHCP can be enabled.
installation & connection INSTALLATION JJ Installation `` This camera is waterproof and in compliance with the IP66 spec, but the jack connected to the external cable is not. You are recommended to install this product below the edge of eaves to prevent the cable from being externally exposed. 2. Fully insert the plastic anchor. Precautions before installation 3. Align the mounting hole of the camera with the hole where the plastic anchor is inserted, then tighten the tapping screw.
7. Insert the rubber stopper again and connect the LAN cable to the Ethernet terminal. 3. Insert the power cable into the small hole made by removing the projected part of the rubber plug in step 2 above, and lay the cable along the long groove. RESET T N AU AL DIO AR M VIDEO AUDIO ALARM USB AC 1 T NET LIN K WO RK NETWORK ACT LINK A DC C 2 12 4V V 2 the ity of lar re Po n. wa d ec tio Be an nn N: ge co IO lta r UT Vo we CA ted po Ra the of 5.
installation & connection Attaching to the unbundled adapter Optional Accessories for Installation 1. Remove the dome cover from the case by referring to the “Disassembling” section. (page 12) 1. FRAME MOUNT(SBP-300WMS)/HANGING MOUNT(SBP-HMS6) This adaptor is used when installing the dome camera onto a wall. Choose and purchase a necessary one of the following options (unbundled) that is suitable to the installation site or for your convenience. 2.
Adjusting the monitoring direction for the camera Pan INSERTING/REMOVING A MICRO SD MEMORY CARD JJ `` Disconnect the power cable from the camera before inserting the Micro SD memory card. Otherwise, it may damage the Micro SD memory card. A DC C 24 12 V V `` When it rains or the humidity is high, insertion or ejection of a Micro SD card is not recommended.
installation & connection Removing a Micro SD Memory Card Gently press down on the exposed end of the memory card as shown in the diagram to eject the memory card from the slot.
Connecting to Audio Input/Output Recommended dongle manufacturer Manufacturer Model WF2123 n300 IP Time N100mini EDIMAX Speaker EW-7811Un TP-LINK TL-WN823N V1 NETGEAR WNA3100M ASUS ●● INSTALLATION & CONNECTION NETIS Microphone Network USB-N13 Power Supply AC + 24V / DC - 12V T F Use the screwdriver to connect each line (+, –) of the power cable to the corresponding power port of the camera.
installation & connection Connecting to the I/O port box Alarm In Wiring Diagram Connect the Alarm I/O cable to the corresponding port of the port box. External connection Inside of the camera VCC_3.3V RESISTOR Sensor ALARM IN (5mA SINK) RESISTOR MLCC A ALAUDIO RM 1 GND AC T NE TW 2 DIODE TRANSISTOR GND LIN K OR RESISTOR K To connect the alarm out If devices (e.g.
CONNECTING THE CAMERA DIRECTLY TO LOCAL AREA NETWORKING + T - DDNS Server (Data Center, KOREA) 24V / DC F N AC + T 12V VIDEO AF W 1. Connect the user PC directly with the network camera. AC 24V / DC F N RESET Camera 12V + T External Remote PC Camera VIDEO AF 12V W / DC 2. Enter the IP address of the camera in the address bar of the browser. RESET 24V DSL/Cable Modem 1. Launch an Internet browser on the local PC. INTERNET - Camera External Remote PC 2.
network connection and setup AF W VIDEO RESET F N + T AF W VIDEO + AF - - 2. Run the Device Manager and change the IP address of the camera so that you can use the web browser on your desktop to connect to the Internet. 3. Use the Internet browser to connect to the web viewer. 4. Move to [Setup] page. 5. Move to [Network] – [DDNS] and configure the DDNS settings. 6. Move to [Basic] – [IP & Port] Setup Page, set the IP type to [PPPoE], and enter the network service’s ID and password. 7.
USING DEVICE MANAGER MM `` Device manager program can be downloaded from - menu at Hanwha Techwin website (http://www.hanwha-security.com). AUTOMATICALLY SEARCHING CAMERA If a camera is connected to the same network of the PC where device manager is installed, you can find network camera by using search function. 1. Click at the main page of device manager. 2. Check the camera from the list. •• Check MAC address at the sticker attached to the camera.
network connection and setup Configuring Dynamic IP Receive IP address from DHCP •• Example of the Dynamic IP environment -- If a Broadband Router, with cameras connected, is assigned an IP address by the DHCP server -- If connecting the camera directly to modem using the DHCP protocols -- If IPs are assigned by the internal DHCP server via the LAN 1. Click the camera from the list that you want to change the IP setting. 2. Click at the main page of device manager. 3.
PORT RANGE FORWARD (PORT MAPPING) SETUP If you have installed a Broadband Router with a camera connected, you must set the port range forwarding on the Broadband Router so that a remote PC can access the camera in it. 1. From the Setup menu of the Broadband Router, select - . For setting the port range forward for a third-party Broadband Router, refer to the user guide of that Broadband Router. 2.
network connection and setup CONNECTING TO THE CAMERA FROM A SHARED LOCAL PC 1. Run device manager. It will scan for connected cameras and display them as a list. 2. Double-click a camera to access. The Internet browser starts and connects to the camera. MM `` Access to the camera can also be gained by typing the camera’s IP address in the address bar of the Internet browser.
web viewer CONNECTING TO THE CAMERA Normally, you would 2. Type the IP address of the camera in the address bar. ex) • IP address (IPv4) : 192.168.1.100 http://192.168.1.100 - the Login dialog should appear. • IP address (IPv6) : 2001:230:abcd: ffff:0000:0000:ffff:1111 http://[2001:230:abcd:ffff:0000:0000:ffff:1111] - the Login dialog should appear. If the HTTP port is other than 80 1. Launch the Internet browser. 2. Type the IP address and HTTP port number of the camera in the address bar.
web viewer PASSWORD SETTING When you access the product for the first time, you must register the login password. When the “Password change” window appears, enter the new password. a new password with 8 to 9 digits, you must use at least 3 of JJ `` For the following: uppercase/lowercase letters, numbers and special characters. For a password with 10 to 15 digits, you must use at least 2 types of those mentioned. -- Special characters that are allowed. : ~`!@#$%^*()_-+=|{}[].
INSTALLING WebViewer PLUGIN If you try to access the plugin free web viewer from IE and request a live view with a codec other than the currently playing codec, or attempt to use the recorded video playback function, an installation message will appear. At this time, the web viewer plugin must be installed to use the functions normally.
appendix SPECIFICATION Items Imaging Device Total Pixels Effective Pixels Video Scanning System Min. Illumination S / N Ratio Video Out Focal Length (Zoom Ratio) Lens 28_ appendix XNV-6120RSA 1945(H) x 1109(V) 2.16M 1945(H) x 1097(V) 2.13M Progressive Scan Color : 0.015 lux(F1.4, 1/30sec), B/W : 0 lux (IR LED On) 50dB Color : 0.07 lux(F1.3, 1/30sec), B/W : 0 lux(IR LED On) IR Viewable Length 1/2.8” 2M CMOS 1945(H) x 1109(V) 2.
Items Video & Audio Analytics Operational Alarm I/O Alarm Triggers Alarm events Pixel Counter Ethernet Video Compression Format Network Resolution Max.
appendix Items Edge Storage Application Programming Interface Network Webpage Language XNV-6080RSA Description XNV-8080RSA XNV-6120RSA SD/SDHC/SDXC 2slot (up to 512 GB) - Continuous recording(1’st slot to 2’nd slot) - Motion Images recorded in the SD/SDHC/SDXC memory card can be downloaded.
PRODUCT OVERVIEW XNV-6080RSA/XNV-8080RSA XNV-6120RSA Unit : mm (inch) Unit : mm (inch) ●● APPENDIX English _31
appendix TROUBLESHOOTING PROBLEM PROBLEM When an Windows 10 user accesses the web viewer through Chrome or Firefox, the sound volume of microphone changes periodically. No video is displayed when accessing the plug-in free webviewer on Safari via HTTPS. SOLUTION yy This is what happens when microphone driver has been set to Realtek driver. Install the High Definition Audio device (Windows Default Driver) or the third party driver as the microphone driver.
OPEN SOURCE ANNOUNCEMENT GPL/LGPL software license If you want to obtain the complete Corresponding Source code in the physical medium such as CD-ROM, the cost of physically performing source distribution might be charged. Component Name License Base Kernel Busybox iproute2-4.3.0 iptables-1.4.21 ethtool-4.2 mtd-1.5.2 mii-diag-2.11 rp-pppoe-3.11 wpa_supplicant-2.5 bash-4.3.30 zeroconf GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 2.0 GPL 3.0 GPL 2.
components (compiler, kernel, and so on) of the operating system on which the executable runs, unless that component itself accompanies the executable. If distribution of executable or object code is made by offering access to copy from a designated place, then offering equivalent access to copy the source code from the same place counts as distribution of the source code, even though third parties are not compelled to copy the source along with the object code. 4.
2. Basic Permissions. All rights granted under this License are granted for the term of copyright on the Program, and are irrevocable provided the stated conditions are met. This License explicitly affirms your unlimited permission to run the unmodified Program. The output from running a covered work is covered by this License only if the output, given its content, constitutes a covered work. This License acknowledges your rights of fair use or other equivalent, as provided by copyright law.
patent license to some of the parties receiving the covered work authorizing them to use, propagate, modify or convey a specific copy of the covered work, then the patent license you grant is automatically extended to all recipients of the covered work and works based on it.
THIS SOFTWARE IS PROVIDED BY THE COPYRIGHT HOLDERS AND CONTRIBUTORS “AS IS” AND ANY EXPRESS OR IMPLIED WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE DISCLAIMED.
above copyright notice, this list of conditions and the following disclaimer in the documentation and/or other materials provided with the distribution. yy Neither the name of Sparta, Inc nor the names of its contributors may be used to endorse or promote products derived from this software without specific prior written permission.
1.11. "Source Code" means the preferred form of the Covered Code for making modifications to it, including all modules it contains, plus any associated interface definition files, scripts used to control compilation and installation of an Executable, or source code differential comparisons against either the Original Code or another well known, available Covered Code of the Contributor’s choice.
provides that the language of a contract shall be construed against the drafter shall not apply to this License. 12. RESPONSIBILITY FOR CLAIMS. As between Initial Developer and the Contributors, each party is responsible for claims and damages arising, directly or indirectly, out of its utilization of rights under this License and You agree to work with Initial Developer and Contributors to distribute such responsibility on an equitable basis.
16. "Patch for Modification" means a difference, program, system, or the like in order to create the Modified Source Code from the Source Code or the Binary Code thereof. 17. "Vicarious Execution of Patch Processing" means vicarious execution service to create the Modified Source Code applying the Patch for Modification to the Source Code or the Binary Code thereof. 18. "Source Code User" means a person who uses the Source Code. 19.
"Legal Entity" shall mean the union of the acting entity and all other entities that control, are controlled by, or are under common control with that entity. For the purposes of this definition, "control" means (i) the power, direct or indirect, to cause the direction or management of such entity, whether by contract or otherwise, or (ii) ownership of fifty percent (50%) or more of the outstanding shares, or (iii) beneficial ownership of such entity.
PHP 3.01 License The PHP License, version 3.01 Copyright (c) 1999 - 2010 The PHP Group. All rights reserved. Component Name License URL php-5.2.17 PHP 3.01 http://www.php.net/distributions Redistribution and use in source and binary forms, with or without modification, is permitted provided that the following conditions are met: 1. Redistributions of source code must retain the above copyright notice, this list of conditions and the following disclaimer. 2.
Head Office 6, Pangyo-ro 319 beon-gil, Bundang-gu, Seongnam-si, Gyeonggi-do, 463-400 Rep. of KOREA Tel : +82.70.7147.8753 Fax : +82.31.8018.3740 www.hanwha-security.com Hanwha Techwin America 500 Frank W. Burr Blvd. Suite 43 Teaneck, NJ 07666 Toll Free +1.877.213.1222 Direct +1.201.325.6920 Fax +1.201.373.0124 www.hanwhasecurity.com Hanwha Techwin Europe Heriot House, Heriot Road, Chertsey, Surrey, KT16 9DT, United Kingdom Tel +44.1932.57.8100 Fax +44.1932.57.8101 www.hanwha-security.
