AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM 2535/2545/2535p/2545p 3502/4502/3502p/4502p 2235/2245/2335/2345 Series Operator Manual Copy Reference Zdsh000j.eps Read this manual carefully before you use this product and keep it handy for future reference. For safety, please follow the instructions in this manual.
AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM Introduction This manual contains detailed instructions on the operation and maintenance of this machine. To get maximum versatility from this machine all operators should carefully read and follow the instructions in this manual. Please keep this manual in a handy place near the machine. Please read the Safety Information before using this machine.
AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM USA (This information is for facsimile option users only.) ❖ FCC Requirements 1. This equipment complies with Part 68 of the FCC rules. On the cover of this equipment is a label that contains, among other information, the FCC registration number and ringer equivalence number (REN) for this equipment. If requested, this information must be provided to the telephone company. 2. This equipment uses the following USOC jack: RJ11C 3.
AdonisC2_ENcopy122F_FM.book Page i Thursday, February 15, 2001 3:23 PM Safety Information When using your equipment, the following safety precautions should always be followed. Safety During Operation In this manual, the following important symbols are used: R WARNING: Indicates a potentially hazardous situation which, if instructions are not followed, could result in death or serious injury.
AdonisC2_ENcopy122F_FM.book Page ii Thursday, February 15, 2001 3:23 PM R CAUTION: • Protect the equipment from dampness or wet weather, such as rain, snow, and so on. • Unplug the power cord from the wall outlet before you move the equipment. While moving the equipment, you should take care that the power cord will not be damaged under the equipment. • When you disconnect the power plug from the wall outlet, always pull the plug (not the cable).
AdonisC2_ENcopy122F_FM.book Page iii Thursday, February 15, 2001 3:23 PM How to Read this Manual Symbols In this manual, the following symbols are used: R WARNING: This symbol indicates a potentially hazardous situation that might result in death or serious injury when you misuse the machine without following the instructions under this symbol. Be sure to read the instructions, all of which are included in the Safety Information section.
AdonisC2_ENcopy122F_FM.book Page iv Thursday, February 15, 2001 3:23 PM TABLE OF CONTENTS Machine Types........................................................................................... 1 What You Can Do with This Machine (Copy Mode)................................ 2 Guide To Components .............................................................................. 5 Output Tray Guide......................................................................................... 7 Options ................
AdonisC2_ENcopy122F_FM.book Page v Thursday, February 15, 2001 3:23 PM Basic Functions....................................................................................... Adjusting Copy Image Density .................................................................... Selecting Original Type Setting................................................................... Selecting Copy Paper ................................................................................. Auto Reduce/Enlarge .................
AdonisC2_ENcopy122F_FM.book Page vi Thursday, February 15, 2001 3:23 PM 1 Sided 8 Pages → Combine 2 Side........................................................... 1 Sided 16 Pages → Combine 2 Side......................................................... 2 Sided 2 Pages → Combine 1 Side........................................................... 2 Sided 4 Pages → Combine 1 Side........................................................... 2 Sided 8 Pages → Combine 1 Side........................................
AdonisC2_ENcopy122F_FM.book Page vii Thursday, February 15, 2001 3:23 PM 3. Document Server Overview................................................................................................. Process ..................................................................................................... Features and Benefits ........................................................................... On Demand Printing..................................................................................
AdonisC2_ENcopy122F_FM.book Page viii Thursday, February 15, 2001 3:23 PM d Adding Staples ................................................................................. 1000-Sheet Finisher.................................................................................. 2 Tray Finisher .......................................................................................... e Removing Jammed Staples............................................................. 1000-Sheet Finisher.......................
AdonisC2_ENcopy122F_FM.book Page ix Thursday, February 15, 2001 3:23 PM 6. REMARKS Do's And Don'ts..................................................................................... Where to Put Your Machine.................................................................. Machine Environment ............................................................................... Moving....................................................................................................... Power Connection.........
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 1 Thursday, February 15, 2001 3:23 PM Machine Types This machine comes in two models which vary by copy speed. To make sure which model you have, see the inside front cover.
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 3 Thursday, February 15, 2001 3:23 PM *1 Optional 2 Tray finisher is reguired. *2 Optional Bridge unit and optional finisher are reguired.
AdonisC2_ENcopy122F_FM.book Page 4 Thursday, February 15, 2001 3:23 PM 1. “Selecting Original Type Setting” ⇒ P.39 23. “2 Sided 8 Pages → Combine 2 Side” ⇒ P.98 2. “Adjusting Copy Image Density” ⇒ P.37 24. “2 Sided 16 Pages → Combine 2 Side” ⇒ P.99 3. “Setting Special Originals” ⇒ P.33 4. “Image Repeat” ⇒ P.112 5. “Double Copies” ⇒ P.113 6. “Centering” ⇒ P.114 7. “Erase” ⇒ P.116 8. “Margin Adjustment” ⇒ P.121 9. “Positive/Negative” ⇒ P.115 10. “Stamp” ⇒ P.123 11. “1 Sided → 2 Sided” ⇒ P.84 12.
AdonisC2_ENcopy122F_FM.book Page 5 Thursday, February 15, 2001 3:23 PM Guide To Components 1. Document Feeder (ADF) 7. Operation switch The document feeder automatically feeds a stack of originals one by one. Press this switch to turn the power on (the On indicator light up). To turn the power off, press this switch again (the On indicator goes off). 2. Exposure glass Place originals here face down for copying. ⇒ P.19 “Originals” 3. Internal tray 8. Control panel ⇒ P.
AdonisC2_ENcopy122F_FM.book Page 6 Thursday, February 15, 2001 3:23 PM 1. Bypass tray 2. Right side cover Use when copying onto OHP transparencies, adhesive labels, translucent paper, postcards, and custom size paper. Open this when a paper jam occurs. 1. Ventilation hole Prevents overheating. Do not obstruct the ventilation hole by placing an object near it or leaning an object against it. If the machine overheats, a fault might occur.
AdonisC2_ENcopy122F_FM.book Page 7 Thursday, February 15, 2001 3:23 PM Output Tray Guide When copying onto OHP transparencies and translucent paper, raise the guide. This prevents copies from being curled when delivered. ❖ To copy onto normal paper and thick paper Slide the guide in the direction of the arrow. ❖ To copy onto OHP transparencies and translucent paper Insert your forefinger into the indent on the guide and slide the guide to the right.
AdonisC2_ENcopy122F_FM.book Page 8 Thursday, February 15, 2001 3:23 PM Options 1. 1000-Sheet Finisher 6. Large Capacity Tray (LCT) Sorts, stacks, and staples copies. Holds 1,500 sheets of paper. 2. External tray 7. Paper tray unit If you selected this as the output tray, copied paper is delivered here face down. Consists of two paper trays. 3. Platen cover Relays copies to the external tray or finisher. Lower this cover over originals for copying. 9. 2 Tray Finisher 4.
AdonisC2_ENcopy122F_FM.book Page 9 Thursday, February 15, 2001 3:23 PM Control Panel 1. Screen Contrast knob 8. {Energy Saver}} key Adjusts the brightness of the display panel. Press to switch to and from Energy Saver mode. ⇒ P.68 “Energy Saver Mode”. 2. Indicators 9. {Interrupt}} key These indicators show errors or the status of the machine. ⇒ P.169 “Troubleshooting”. Press to make interrupt a long copy job to make copies. ⇒ P.68 “Interrupt Copy”. 3.
AdonisC2_ENcopy122F_FM.book Page 10 Thursday, February 15, 2001 3:23 PM 14. {Clear/Stop}} key • Clear Press to delete a number entered. • Stop Press to stop a copy job in progress. 15. {#}} key Press to enter a value. 16. Number keys Use to enter the desired number of copies and data for selected modes. 17. Function keys Press the appropriate key to choose any of the following functions: • • • • • Copy Document Server Facsimile Printer Scanner 18.
AdonisC2_ENcopy122F_FM.book Page 11 Thursday, February 15, 2001 3:23 PM Display Panel The display panel shows the status of the machine, error messages and function menus. Important ❒ Do not apply a strong shock or force of about 30 N (about 3 kgf) or more to the display panel. If you do, the display might be damaged. Note ❒ The function items displayed serve as selector keys. You can select or specify an item by lightly pressing it.
AdonisC2_ENcopy122F_FM.book Page 12 Thursday, February 15, 2001 3:23 PM 6. Displays the contents of the 7. Shows the available functions. Shortcut keys. You can register frequently used functions in these keys. ⇒ “Copy Function Key F1-F5” in P.217 “General Features 3/4”. Press a function name to display its menu. For example, press the [Reduce/Enlarge] key to bring up the Reduce/Enlarge menu. 8. A clip mark appears for a currently selected function. ❖ Function menu 1. Items you can select. 2.
AdonisC2_ENcopy122F_FM.book Page 13 Thursday, February 15, 2001 3:23 PM Function List Based on Options The functions that are available to you depend on your machine configuration and which options you have. See the table below.
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 15 Thursday, February 15, 2001 3:23 PM 1. Basics Turning On the Power To turn the machine on, press the operation switch. Note ❒ This machine automatically enters Energy Saver mode or turns itself off if you do not use the machine for a while. P.30 “Auto Off” and “Timer Setting” in the System Settings manual. Turning On the Main Power A Make sure that the power cord is firmly plugged into the wall outlet.
AdonisC2_ENcopy122F_FM.book Page 16 Thursday, February 15, 2001 3:23 PM Basics Turning On the Power Turning Off the Power A Press A Make sure that the platen cover or the operation switch to make the On indicator goes on. The display panel will come on. 1 the document feeder is in the right position. B Press the operation switch to make the On indicator goes off. Note ❒ If the power is not turned on when the operation switch is pressed, check if the main power switch is on. If off, turn it on.
AdonisC2_ENcopy122F_FM.book Page 17 Thursday, February 15, 2001 3:23 PM Turning On the Power Turning Off the Main Power A Make sure that the On indicator goes off. 1 B Turn off the main power switch to make sure the indicator goes off. Important ❒ Do not turn off the main power switch when the indicator goes on or blink Hard Disk or Memory might be broken. ❒ Pull out the power plug after you turn off the main power switch. Hard Disk or Memory might be broken.
AdonisC2_ENcopy122F_FM.book Page 18 Thursday, February 15, 2001 3:23 PM Basics Changing Modes You can use this machine not only as a copier, but also as a fax, printer, document server and scanner as well. Press the {Copy}, {Facsimile}, {Printer}, {Scanner} or {Document Server} key to use that function.
AdonisC2_ENcopy122F_FM.book Page 19 Thursday, February 15, 2001 3:23 PM Originals Originals Sizes and Weights of Recommended Originals 1 ❖ Metric version Where Original Is Set Original Size Original Weight Exposure glass Up to A3 -- Document feeder 1-sided originals: 40 – 128g/m2 A3L – B6KL 2-sided originals: 52 – 105g/m2 A3L – A5KL ❖ Inch version Where Original Is Set Original Size Original Weight Exposure glass Up to 11" × 17" -- Document feeder 1-sided originals: 11 – 34 lb.
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 21 Thursday, February 15, 2001 3:23 PM Originals Missing Image Area ❖ Exposure glass 1 Reference position Horizontal size Vertical size Maximum Scanning area A3 (297x420mm) 11"x17" (279x432mm) ❖ Document feeder Limitation ❒ Even if you correctly set originals in the document feeder or on the exposure glass, 3mm (0.1") margins on all four sides of the original might not be copied.
AdonisC2_ENcopy122F_FM.book Page 22 Thursday, February 15, 2001 3:23 PM Basics Copy Paper Recommended Paper Sizes and Types 1 The following limitations apply to each tray: Tray 1 *4 Tray 2 *4 Metric Version Inch Version A3L, B4L, A4KL, B5KL, , <11" × 17"L>, <81/2" × 14"L>, <81/2" × 11"KL>, <8" × 13"L>, <81/2" × 13"L>, <81/4" × 13"L>, <81/4" × 14"L>, <11" × 14"L>, <71/4" × 101/2"L>, <8" × 101/2"KL>, <51/2" × 81/2"L> 64-105g/m2 500 sheet , (17-28lb.
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 24 Thursday, February 15, 2001 3:23 PM Basics Important ❒ If you use damp or curled paper, a misfeed might occur. In this case, try turning over the paper stack in the paper tray. If there is no improvement, change to paper with less curl. 1 Note ❒ When you use the bypass tray, it is recommended to set the copy paper direction to L. ❒ Postcards should be fed from the bypass tray.
AdonisC2_ENcopy122F_FM.book Page 25 Thursday, February 15, 2001 3:23 PM Copy Paper Direction-fixed paper or 2-sided paper The direction-fixed (top to bottom) or 2-sided paper (letterhead paper, punched paper, or copied paper, e.g.) might not be printed correctly depending on how the originals and paper are set in place. Set "Letterhead setting" of system settings and then set the original and paper as shown below. ⇒ “Letterhead Setting” in ⇒ P.
AdonisC2_ENcopy122F_FM.book Page 26 Thursday, February 15, 2001 3:23 PM Basics Non-recommended Paper R CAUTION: • Do not use aluminum foil, carbon paper, or similar conductive paper to avoid a fire or equipment failure. 1 Important ❒ Do not use any of the following kinds of paper or a fault might occur.
AdonisC2_ENcopy122F_FM.book Page 27 Thursday, February 15, 2001 3:23 PM Toner Toner Handling Toner 1 R WARNING: • Do not incinerate used toner or toner containers. Toner dust might ignite when exposed to an open flame. Dispose of used toner containers in accordance with local regulations for plastics. R CAUTION: • Keep toner (used or unused) and toner containers out of reach of children.
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 29 Thursday, February 15, 2001 3:23 PM 2. Copying Basic Procedure A Make sure that the machine is in Copy mode. If the machine is not in Copy mode, press the {Copy} key. B When the machine is set for the user code, enter the user code with the number keys and then press the {#} } key. Reference ⇒ P.68 “Other Functions”. C Make sure that there are no previous settings remaining. Note ❒ To clear settings, press the {Clear Modes} key. D Set your originals. Reference ⇒ P.
AdonisC2_ENcopy122F_FM.book Page 30 Thursday, February 15, 2001 3:23 PM Copying - System Reset The machine returns to its initial condition automatically when your job is finished, after a certain period of time. This function is called “System Reset”. 2 Note ❒ You can change the System Reset time. ⇒ “System Reset Timer” in “System Settings manual”. - Auto Off The machine turns itself off automatically after your job is finished, after a certain period of time. This function is called “Auto Off”.
AdonisC2_ENcopy122F_FM.book Page 31 Thursday, February 15, 2001 3:23 PM Setting Originals Setting Originals Limitation ❒ Set originals after correction fluid and ink has completely dried. Not taking this precaution could mark the exposure glass and cause marks to be copied. Note ❒ Basically originals should be aligned to the rear left corner. However, some copy functions may produce different results depending on the direction of the originals. For details, see the explanations of each function.
AdonisC2_ENcopy122F_FM.book Page 32 Thursday, February 15, 2001 3:23 PM Copying Setting Originals in the Document Feeder Note ❒ The last page should be on the bottom. ❒ Do not stack originals beyond the limit mark on the side fence of the document feeder. ❒ The original might become dirty if it is written with a pencil or similar tools. 2 Reference Regarding originals that the document feeder can handle. ⇒ P.19 “Originals”.
AdonisC2_ENcopy122F_FM.book Page 33 Thursday, February 15, 2001 3:23 PM Setting Originals 90° Turn Setting Special Originals When you want to copy A3K, B4K or 11" × 17"K size originals, set your original in the landscape orientation and then press the key. The machine rotates the original image and you can make copies as you wish. This is useful for copying large originals with the Staple, Punch, Duplex, Combine or Stamp functions.
AdonisC2_ENcopy122F_FM.book Page 34 Thursday, February 15, 2001 3:23 PM Copying C Press the [OK] key. Mixed Size mode When originals of different sizes are set on the document feeder at a time, the machine automatically checks the size of the originals and makes copies. 2 D Set your originals, then press the {Start} } key. E After all the previously set origi- nals are fed, set the next originals. The second and subsequent originals can be fed automatically without pressing the {Start} key.
AdonisC2_ENcopy122F_FM.book Page 35 Thursday, February 15, 2001 3:23 PM Setting Originals A Press the [Special Original] key. Setting Custom Size Originals When setting custom size originals in the document feeder, specify the size of the originals. Limitation ❒ The paper size that can be set with this function is vertical 128-297mm (5" – 11"), horizontal 128-1,260mm (5" – 49"). B Press the [Mixed size] key. 2 A Press the [Special Original] key. C Press the [OK] key.
AdonisC2_ENcopy122F_FM.book Page 36 Thursday, February 15, 2001 3:23 PM Copying Note ❒ If you make a mistake, press the [Clear] or {Clear/Stop} key, and then enter the value again. D Enter the vertical size of the original with the Number keys, then press the [#] key. 2 E Press the [OK] key. F Set your originals, then press the {Start} } key.
AdonisC2_ENcopy122F_FM.book Page 37 Thursday, February 15, 2001 3:23 PM Basic Functions Basic Functions The following basic functions are explained in this section. ❖ Adjusting Copy Image Density Auto and Manual Image Density ❖ Selecting Original Type Setting Text, Text·Photo, Photo, Pale, Generation Copy ❖ Selecting Copy Paper Auto Paper Select and Manual Paper Select ❖ Auto Reduce/Enlarge The machine can choose an appropriate reproduction ratio based on the paper and original sizes you select.
AdonisC2_ENcopy122F_FM.book Page 38 Thursday, February 15, 2001 3:23 PM Copying Auto Image Density A Make sure that the [Auto Image Density] key is selected. Combined Auto and Manual Image Density A Make sure that the [Auto Image Density] key is selected. B Press the [Lighter] or [Darker] key to 2 adjust the density. Note ❒ If the [Auto Image Density] key is not selected, press the [Auto Image Density] key. ❒ If you do not wish to set any other functions, press the {Start} key to start copying.
AdonisC2_ENcopy122F_FM.book Page 39 Thursday, February 15, 2001 3:23 PM Basic Functions Selecting Original Type Setting A Press the appropriate key to select the original type. Select one of the following types to match your originals: ❖ Text Select this mode when your originals contain only letters (no pictures). ❖ Text·Photo Select Text·Photo when your originals contain photographs or pictures with letters. ❖ Photo Delicate tones of photographs and pictures can be reproduced with this mode.
AdonisC2_ENcopy122F_FM.book Page 40 Thursday, February 15, 2001 3:23 PM Copying Selecting Copy Paper There are two ways to select copy paper: ❖ Auto Paper Select The machine selects a suitable size of copy paper automatically based on the original size and the reproduction ratio. ⇒ P.42 “Rotated copy”. 2 ❖ Manual Paper Select Choose the tray containing the paper you wish to copy onto: Paper Tray, Bypass Tray or large capacity tray (LCT). Reference ⇒ P.60 “Copying from the Bypass Tray”.
AdonisC2_ENcopy122F_FM.book Page 41 Thursday, February 15, 2001 3:23 PM Basic Functions Auto Paper Select A Make sure that the [Auto Paper Select] key is selected. 2 Note ❒ If the [Auto Paper Select] key is not selected, press the [Auto Paper Select] key. ❒ If you do not wish to set any other functions, press the {Start} key to start copying. ❒ If “Yes” has been selected in “Original Mode Display” of the User Tools, press the [Auto Paper Select] key.
AdonisC2_ENcopy122F_FM.book Page 42 Thursday, February 15, 2001 3:23 PM Copying - Rotated copy If the direction in which your original is set (landscape or portrait) is different from that of the paper you are copying onto, this function rotates the original image by 90° and fits it on the copy paper. This function works when Auto Paper Select or Auto Reduce/Enlarge is selected. ⇒ “Auto Paper Select” in P.40 “Selecting Copy Paper” and ⇒ P.43 “Auto Reduce/Enlarge”.
AdonisC2_ENcopy122F_FM.book Page 43 Thursday, February 15, 2001 3:23 PM Basic Functions Auto Reduce/Enlarge The machine can choose an appropriate reproduction ratio based on the paper and original sizes you select. ❖ Inch version Where Original Is Set Original Size and Direction Exposure glass 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL Document feeder *1 A4KL, 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL, 51/2" × 81/2"KL *1 Limitation ❒ You cannot use the bypass tray with this function.
AdonisC2_ENcopy122F_FM.book Page 44 Thursday, February 15, 2001 3:23 PM Copying Sort/Stack/Staple The machine can scan your originals into memory and automatically sort the copies.
AdonisC2_ENcopy122F_FM.book Page 45 Thursday, February 15, 2001 3:23 PM Sort/Stack/Staple ❖ Inch version Internal tray • 81/2" × 14"L or larger: 250 sheets (20 lb.) • 81/2" × 11K or smaller: 500 sheets (20 lb.) Internal tray 2 (1 bin tray) 125 sheets (20 lb.) Sort Copies can be assembled as sets in sequential order. ❖ Sort Copies can be assembled as sets in sequential order. 2 Extar125 sheets (20 lb.) nal tray 1000• 81/2" × 14"L or larger: 500 Sheet sheets (20 lb.
AdonisC2_ENcopy122F_FM.book Page 46 Thursday, February 15, 2001 3:23 PM Copying ❒ The paper sizes that can be used in the Rotate Sort function are as follows: 2 Metric version A4KL, B5KL Inch version 81/2" × 11"KL 1000-Sheet Finish- 2 Tray er Finisher ❒ To use the Rotate Sort function, two paper trays identical in size and different in direction (KL) are required. Metric A3L, B4L, version A4KL, B5KL, A5KL, B6L, A6L Reference For the paper capacity of the optional finishers, ⇒ P.
AdonisC2_ENcopy122F_FM.book Page 47 Thursday, February 15, 2001 3:23 PM Sort/Stack/Staple ❖ When the 2 Tray Finisher is installed Note ❒ When the optional finisher is installed, use the User Tools to display [Rotate Sort]. ⇒ “Select Stack Function” in P.233 “Input/Output”. B Enter the number of copy sets with the number keys. Limitation ❒ The maximum number of sets is 999. Note ❒ To change the entered number, press the {Clear/Stop} key. C Set your originals, then press the {Start} } key.
AdonisC2_ENcopy122F_FM.book Page 48 Thursday, February 15, 2001 3:23 PM Copying A Press the [Stack] key. Stack Copies can be assembled with each page set. ❖ Shift Stack • 1000-Sheet/2 Tray-Sheet Finisher This function groups copies of each page in a multi-page original together. Every other page stack is shifted for ease of separation. The finisher shift tray of the finisher provides this function by sliding from side to side. 2 2 3 Note ❒ To change the entered number, press the {Clear/Stop} key.
AdonisC2_ENcopy122F_FM.book Page 49 Thursday, February 15, 2001 3:23 PM Sort/Stack/Staple B Set the next original. When it is placed on the exposure glass, press the {Start} } key. Note ❒ Set the original in the same direction as the first one.
AdonisC2_ENcopy122F_FM.book Page 50 Thursday, February 15, 2001 3:23 PM Copying Staple The optional finisher and the bridge unit are required to use this function. Each copy set can be stapled together. 2 Limitation ❒ You cannot use the following paper in this function: • Postcards • Translucent paper • OHP transparencies • Adhesive labels • Curled paper • Low stiffness paper • Paper of different vertical sizes Note ❒ For this mode, the following limitation applies.
AdonisC2_ENcopy122F_FM.book Page 51 Thursday, February 15, 2001 3:23 PM Sort/Stack/Staple ❖ Inch version With 1000-Sheet Finisher With 2 Tray Finisher Paper size 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL 11" × 17"L, 81/2" × 14"L, 81/2" × 11"KL Stapler capacity • 81/2" × 11" or smaller: 30 sheets (20 lb.) • 81/2" × 11" or smaller: 50 sheets (20 lb.) • 81/2" × 14" or larger: 20 sheets (20 lb.) • 81/2" × 14" or larger: 30 sheets (20 lb.) 2 • Mixed Size: 30 sheets (20lb.
AdonisC2_ENcopy122F_FM.book Page 52 Thursday, February 15, 2001 3:23 PM Copying ❖ 1000-sheet Finisher When your machine is equipped with the 1000-sheet finisher, the stapling position will be fixed to “Top Slant”. Original setting Exposure glass Document Feeder Stapling position K Top Slant 2 STAPLEBE L Note ❒ Original images are not rotated.
AdonisC2_ENcopy122F_FM.book Page 53 Thursday, February 15, 2001 3:23 PM Sort/Stack/Staple Original setting Exposure glass Document Feeder STAPLEDE Left 2 K Stapling position *1 2 L STAPLE31 K STAPLE33 STAPLE32 *1 Top 2 STAPLEEE *1 L Available staple positions except A3, B4, size of paper. Note ❒ You cannot change stapling positions during copying. ❒ When the original image is rotated, the stapling direction turns by 90°.
AdonisC2_ENcopy122F_FM.book Page 54 Thursday, February 15, 2001 3:23 PM Copying ❖ 2 Tray Finisher 2 Note ❒ When you select the stapling position, Sort mode is automatically selected. Reference ⇒ P.51 “Stapling position and original setting” B Enter the number of copy sets with the number keys. Note ❒ To change the entered number, press the {Clear/Stop} key. C Set your originals, then press the {Start}} key.
AdonisC2_ENcopy122F_FM.book Page 55 Thursday, February 15, 2001 3:23 PM Sort/Stack/Staple To Stop Scanning Temporarily When you are using the Sort, Stack, or Staple function, the originals are scanned into memory. A Press the {Clear/Stop}} key to stop originals from being scanned into memory. To resume scanning A Press the [No] key to resume scanning. Note ❒ Scanned images in memory are not cleared. To clear scanned images of the originals A Press the [Yes] key.
AdonisC2_ENcopy122F_FM.book Page 56 Thursday, February 15, 2001 3:23 PM Copying Punch The optional 2 tray finisher and the bridge unit are required to use this function. This function is used to make punch holes in copies.
AdonisC2_ENcopy122F_FM.book Page 57 Thursday, February 15, 2001 3:23 PM Punch Note ❒ When using Punch and Combine, Double Copies, or Auto Reduce/Enlarge, the message "Blank part will appear. Check orientation." may appear because of the orientation of the original and the copy paper. If this occurs, change the orientation of the copy paper.
AdonisC2_ENcopy122F_FM.
AdonisC2_ENcopy122F_FM.book Page 59 Thursday, February 15, 2001 3:23 PM Punch B Enter the number of copy sets with the number keys. Note ❒ To change the entered number, press the {Clear/Stop} key. ❒ If you wish to use the Sort function, press the [Sort] key. C Set your originals, then press the {Start}} key.
AdonisC2_ENcopy122F_FM.book Page 60 Thursday, February 15, 2001 3:23 PM Copying Copying from the Bypass Tray Use the bypass tray to copy onto OHP transparencies, adhesive labels, translucent paper, postcards, and copy paper that cannot be set in the paper tray. 2 A Open the bypass tray.
AdonisC2_ENcopy122F_FM.book Page 61 Thursday, February 15, 2001 3:23 PM Copying from the Bypass Tray ❒ If the beeper is turned off, lightly insert the copy paper until it stops. Refer to the System Settings manual. ❒ When the document feeder is open, set the direction of the copy paper to L. ❒ Swing out the extender to support paper sizes larger than A4L, 81/2" × 11"L. ❒ Fan paper to get air between the sheets and avoid a multi-sheet feed. ❒ Before setting, adjust the paper if curled or warped.
AdonisC2_ENcopy122F_FM.book Page 62 Thursday, February 15, 2001 3:23 PM Copying B Press the [Custom Size] key. 2 C Press the [Vertical mm] key and enter the vertical size of the paper with the number keys, then press the [#] key. E To register the custom size entered, press the [Store] key and then press the [Cancel] key. Note ❒ If you do not register the custom size, go to step F. ❒ Only one custom size can be stored. ❒ To recall the custom size stored, press the [Recall] key.
AdonisC2_ENcopy122F_FM.book Page 63 Thursday, February 15, 2001 3:23 PM Copying from the Bypass Tray When Copying onto OHP Transparencies or Thick Paper To make copies onto OHP transparencies or thick paper, you need to specify the paper type. Note ❒ Select [Thick Paper] if the paper weight is more than 128g/m2, 34 lb. A Open the bypass tray, and adjust E Press the [OK] key. F Set your originals and press the {Start} } key.
AdonisC2_ENcopy122F_FM.book Page 64 Thursday, February 15, 2001 3:23 PM Copying Programs You can store frequently used copy job settings in machine memory, and recall them for future use. ❖ Storing Your Settings You can store your settings you frequently use. 2 ❖ Deleting A Program You can delete a stored program. Storing a Program A Edit the copy settings so that all functions you want to store in this program are selected. B Press the {Program}} key.
AdonisC2_ENcopy122F_FM.book Page 65 Thursday, February 15, 2001 3:23 PM Programs Note ❒ If you do not wish to enter the program name, go to step F. ❒ You can register up to 40 characters. ❒ To change the name entered, press the [Backspace], [Delete] or {Clear/Stop} key and enter new letters. Reference For details on entering characters, ⇒ "Entering Text Characters" in the System Settings manual. F Press the [OK] key. When the settings are successfully stored, the m indicator goes on.
AdonisC2_ENcopy122F_FM.book Page 66 Thursday, February 15, 2001 3:23 PM Copying Recalling a Program A Press the {Program}} key. 2 B Press the [Recall] key. C Press the program number you want to recall. The stored settings are displayed. Note ❒ Only programs with m contain a program. D Set your originals, then press the {Start} } key.
AdonisC2_ENcopy122F_FM.book Page 67 Thursday, February 15, 2001 3:23 PM Job Preset Job Preset If a long copy job is in progress and you do not wish to wait for it to finish, you can use this function to set up the next one copy job in advance. When the current copy job is finished, your copy job will be started automatically. A Press the {Copy}} key. D Press the [To "Printing"] key. After the current copy job, the next job starts automatically.
AdonisC2_ENcopy122F_FM.book Page 68 Thursday, February 15, 2001 3:23 PM Copying Other Functions 2 Energy Saver Mode Interrupt Copy If you do not operate the machine for a certain period after copying, or when you press the {Energy Saver} key, the display disappears and the machine enters Energy Saver mode. When you press the {Energy Saver} key again, the machine returns to the ready condition. In Energy Saver mode, the machine uses less electricity.
AdonisC2_ENcopy122F_FM.book Page 69 Thursday, February 15, 2001 3:23 PM Other Functions To interrupt copying after all originals have been fed Sample Copy A Press the {Interrupt}} key. Use this function to check a copy set before making a long copy run. The Interrupt indicator goes on. Note ❒ Copying will not stop yet. B Set your original. C Press the {Start}} key. The machine stops the original job and starts copying your original. D When copying is complete, remove your originals and copies.
AdonisC2_ENcopy122F_FM.book Page 70 Thursday, February 15, 2001 3:23 PM Copying Changing the Number of Sets You can change the number of copy sets during copying. Limitation ❒ This function can be used only when the Sort function has been turned on. 2 A Press the {Clear/Stop} } key when “Copying” is displayed. B Press the [Change Quantity] key. C Enter the number of copy sets with the number keys, then press the {#} } key.
AdonisC2_ENcopy122F_FM.book Page 71 Thursday, February 15, 2001 3:23 PM Preset Reduce/Enlarge Preset Reduce/Enlarge You can select a preset ratio for copying. ❖ Metric version Ratio (%) Note ❒ You can select one of 12 preset ratios (5 enlargement ratios, 7 reduction ratios). ❒ Use “Create Margin” to reduce the image to 93% of its original size with the centre as reference. You can register this function in a shortcut key on the initial display.
AdonisC2_ENcopy122F_FM.book Page 72 Thursday, February 15, 2001 3:23 PM Copying 2 Ratio (%) Original → Copy paper size 73 11" × 15"→81/2" × 11" 65 11" × 17"→81/2" × 11" 50 (reduce area by /4) 11" × 17"→51/2" × 81/2" 25 -- 1 A Press the [Reduce/Enlarge] key. Create Margin mode Use “Create Margin” to reduce the image by 93% of its original size with the centre position as reference. You can register this function in a shortcut key on the initial display.
AdonisC2_ENcopy122F_FM.book Page 73 Thursday, February 15, 2001 3:23 PM Zoom Zoom You can change the reproduction ratio in 1% steps. B Enter the ratio. To select the ratio with the [n] and [o] keys 2 A Select a preset ratio which is close to the desired ratio by using [Reduce] or [Enlarge]. Note ❒ The following ratios can be selected: • Metric version: 25 – 400% • Inch version: 25 – 400% ❒ You can select a ratio regardless of the size of an original or copy paper.
AdonisC2_ENcopy122F_FM.book Page 74 Thursday, February 15, 2001 3:23 PM Copying B Enter the desired ratio with the number keys. Note ❒ To change the ratio entered, press the [Clear] or {Clear/ Stop} key and enter the new ratio. C Press the [#] key. D Press the [OK] key. 2 C Set your originals, then press the {Start} } key.
AdonisC2_ENcopy122F_FM.book Page 75 Thursday, February 15, 2001 3:23 PM Size Magnification Size Magnification This function calculates an enlargement or reduction ratio based upon the lengths of the original and copy. B Press the [Specifid Ratio] key. 2 Amm amm C Make sure that the [Specifid Ratio] key is highlighted. Preparation Measure and specify the lengths of the original and copy by comparing “A” with “a.
AdonisC2_ENcopy122F_FM.book Page 76 Thursday, February 15, 2001 3:23 PM Copying E Enter the length of the copy with the number keys and press the [#] key. Note ❒ To change the length entered, press the [Clear] or {Clear/Stop} key and enter the new length. ❒ To change the length after pressing the [#] key, select [Original] or [Copy] and enter the desired length. 2 F Press the [OK] key. G Press the [OK] key. H Set your original, then press the {Start} } key.