User's Manual
Table Of Contents
- STT-31EFI Operators Manual 03251
- GENERAL INFORMATION
- SAFETY INFORMATION
- SPECIFICATIONS
- OPERATING INSTRUCTIONS
- 4.1 Controls And Instrument Identification
- 4.2 Safety Interlock System
- 4.3 Initial Run-In Procedures
- 4.4 Starting The Engine
- 4.5 Ground Travel And Steering
- 4.6 Engaging The Deck Drive (Cutter Blades)
- 4.7 Hillside Operation
- 4.8 Parking The Mower
- 4.9 After Operation
- 4.10 Removing Clogged Material
- 4.11 Moving Mower With Engine Stopped
- 4.12 Recommendations For Mowing
- 4.13 Adjusting Cutting Height
- 4.14 Adjusting The Steering Levers
- 4.15 Adjusting The Height Adjust Pedal
- 4.16 Towing (Optional Hitch Accessory)
- TROUBLESHOOTING CUTTING CONDITIONS
- ADJUSTMENTS
- MAINTENANCE
- ILLUSTRATED PARTS LIST
- 8.1 Scag Approved Attachments And Accessories
- ELECTRICAL SCHEMATIC (KOHLER 31HP - EFI)
- REPLACEMENT DECALS AND INFORMATION PLATES
- ELECTRICAL SYSTEM (31HP-EFI KOHLER)
- BDP-16A HYDRAULIC PUMP ASSEMBLY WITH COOLING FAN
- FUEL AND HYDRAULIC SYSTEM - KOHLER 31EFI
- BRAKE AND STEERING COMPONENTS
- DECK DRIVE COMPONENTS
- STT ROLL-OVER PROTECTION SYSTEM - WITH SUSPENSION SEAT
- SHEET METAL COMPONENTS
- CUTTER DECK CONTROLS
- 61V & 72VS CUTTER DECKS
- NOTES
- LIMITED WARRANTY - COMMERCIAL EQUIPMENT
22
R
CONDICIÓN CAUSA SOLUCIÓN
RASPADORAS - LAS
CUCHILLAS PEGAN EN LA
TIERRA O ESTÁN CORTANDO
MUY CERCA AL TERRENO
Ancho de la
plataforma de corte
SGB022
Baja presión de las llantas Verifique y ajuste las presiones
Velocidad demasiado alta
Disminuya la velocidad para ajustarse
a las condiciones del terreno
Corte demasiado bajo
Se puede tener que reducir la
velocidad en el terreno, aumentar
la altura de la plataforma de corte,
cambiar la dirección del corte y/o
cambiar la inclinación y el nivel
Terreno rugoso
Se puede tener que reducir la
velocidad en el terreno, aumentar la
altura de la plataforma de corte y/o
cambiar la dirección del corte
Velocidad demasiado alta
Disminuya la velocidad para ajustarse
a las condiciones del terreno
Césped mojado Corte el césped una vez que se seque
CORTE LATERAL - CRESTA
EN EL CENTRO DE LA
TRAYECTORIA DE CORTE
Ancho de la
plataforma de corte
SGB024
Cuchillas mal montadas, disparejas Ajuste la inclinación y el nivel
Cuchilla doblada Reemplace la cuchilla
Falla del eje interno
Consulte con su distribuidor SCAG
autorizado
Montaje incorrecto del eje
Consulte con su distribuidor SCAG
autorizado
CORTE INCLINADO -
CRESTAS INCLINADAS A
TRAVÉS DEL ANCHO DE LA
TRAYECTORIA DE CORTE
Ancho de la
plataforma de corte
SGB025
Área de montaje del eje doblada
Consulte con su distribuidor SCAG
autorizado
Falla del eje interno
Consulte con su distribuidor SCAG
autorizado
Alojamiento de la plataforma doblado
Consulte con su distribuidor SCAG
autorizado
IDENTIFICACIÓN DE FALLAS EN LAS CONDICIONES DE CORTE
(CONTINUACIÓN)
Section 5