P516-271 CO-200 OFFLINE LOCK USER GUIDE INSTRUCTIONS FOR CO-SERIES OFFLINE LOCKS Para el idioma español, navegue hacia www.schlage.com/support. Pour la portion française, veuillez consulter le site www.schlage.com/support.
CO-200 Offline Lock User Guide CONTENTS Overview........................................................................................................................................ 3 Getting Started .............................................................................................................................. 4 Schlage Utility Software (SUS) ...................................................................................................... 4 Construction Access Mode ..................
CO-200 Offline Lock User Guide OVERVIEW The Schlage CO-200 is an off-line electronic lock in the CO-Series product line. • The lock is configured to operate as Classroom/Storeroom function. Optional Office or Privacy functions are available. • The lock is powered by four (4) AA batteries. See Batteries on page 12 for more information. • Outside lever is normally locked. • Inside lever always allows egress. • The lock maintains an audit trail of events in the normal operating mode.
CO-200 Offline Lock User Guide GETTING STARTED Follow these steps when setting up a new lock. 1. Install the lock. See the installation guide that came with the lock, or visit www.schlage.com/support, for more information. 2. Make sure the batteries are installed properly. See Batteries on page 12 for more information. 3. Before programming, the lock may be used in Construction Access Mode. See Construction Access Mode on page 5 for more information.
CO-200 Offline Lock User Guide CONSTRUCTION ACCESS MODE Construction Access Mode is used to allow access before the lock has been programmed, and for testing purposes. • Enabled by default. • The lock will remain in Construction Access Mode until the mode is cancelled as described below. • No audits are captured while lock is in Construction Access Mode. Create the Master Construction Credential - Locks with Card Readers 1. Press and hold the Schlage button while presenting a credential. 2.
CO-200 Offline Lock User Guide MANUAL LOCK PROGRAMMING Right LED Left LED TIPS The Schlage button has two different LEDs, one on the left and one on the right. All locks have a default programming code of 97531 and “* ”. All locks have a default normal use code of 13579 and “#”. ! When adding a card credential, the 3-6 digit code (PIN) entered prior to presenting the card becomes the credential reference number. This number can be used to delete a card without physically having the card.
CO-200 Offline Lock User Guide Manual Programming Commands Commands are confirmed by five alternating green blinks of the Schlage button. Programming mode will time out if no entry is made in 20-25 seconds. Time out is indicated by red blinks of the Schlage button, three left and nine right at the same time. The right LED on the Schlage button will blink green to indicate an incorrect entry. To interpret blink patterns, refer to Error Codes on page 9.
CO-200 Offline Lock User Guide Function Press/Present OR Programming Card [Programming Code] Wait For Confirmation1 Wait for Add Freeze Credential New [PIN] OR (for PIN only) add another credential OR [Programming Code] OR New Card to stop flashing between each step. to finish Programming Card Wait for Add Freeze +PIN Credential to stop flashing between each step.
CO-200 Offline Lock User Guide Function Press/Present OR Programming Card [Programming Code] Change PIN Length Press , , , OR for desired PIN length Wait For Confirmation1 Wait for to stop flashing between each step. to finish 1 Other lights may show before the final confirmation. Wait for final confirmation before continuing to the next step. ERROR CODES All error codes are indicated on the Schlage button by a solid red LED and a blinking green LED.
CO-200 Offline Lock User Guide TEST LOCK OPERATION If you encounter problems while performing any of the following tests, review the installation guide and correct any problems. Mechanical Test 1. Rotate the inside lever or depress the push bar to open the door. Operation should be smooth, and the latch should retract. 2. Insert the key into the keyway and rotate the key and the outside lever to open the door. Operation should be smooth, and the latch should retract. Test in Factory Default Mode 1.
CO-200 Offline Lock User Guide RESET TO FACTORY DEFAULTS ! ! All information in the lock will be deleted and reset to factory defaults! The door must be locked (not toggled open or in the middle of normal access) before resetting to factory defaults. Level 1 Factory Default Reset Level 1 factory default reset will delete configurations and settings in the main controller in the lock. Main controller configurations that will reset to factory default include: programming and user codes.
CO-200 Offline Lock User Guide BATTERIES To Install or Replace Alkaline Batteries Battery voltage can be checked with the SUS. Changing batteries does not affect any programmed data. 1. Remove the battery cover. 2. Remove the battery bracket. ! Do not allow the battery pack to hang from the wires. 3. Install the new batteries (install only new AA Alkaline batteries). Make sure the batteries are installed in the correct orientation. 4. Reinstall the battery pack and battery bracket. 5.
CO-200 Offline Lock User Guide LED REFERENCE Most LED indicators are configured with the SUS. See SUS User Guide for more information.
CO-200 Offline Lock User Guide TROUBLESHOOTING Problem The lock beeper does not sound and the keypad does not light when the Schlage button is pressed. Possible Cause Solution The beeper may be turned off. Use manual programming or the SUS to enable the beeper (see Disable/Enable Beeper on page 7 or the SUS User Guide for more information) The battery or wired power may be improperly connected. The batteries may be inserted with incorrect polarity.
CO-200 Offline Lock User Guide Problem Possible Cause Solution The LEDs and beeper indicate a replaced and/or incompatible reader (3 red blinks and 3 beeps with each card or key press, or 5 red blinks and 5 beeps on power-up). The reader is not the original reader matched with the lock at the factory. If the reader was replaced, check that the new reader is an identical type to the original reader (i.e., replace magswipe with magswipe).
FCC STATEMENTS Ingersoll Rand Agency Statements Compliance Statement (Part 15.19) This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions: 1. This device may not cause harmful interference, and 2. This device must accept any interference received, including interference that may cause undesired operation. Warning (Part 15.