Installation manual

Configuration Mode (ConF)
S1A28692 03/2010 145
Parameters described in this page can be accessed by:
IA01 [Analog input 1 assignment]
[No] (nO)
nO
A11
A12
A13
OCr
OFr
OrP
trq
Stq
OrS
OPS
OPF
OPE
OPI
OPr
tHr
tHd
tqMS
UPdt
UPdH
LCC
Mdb
CAn
nEt
OFS
tHr2
tHr3
tqL
UOP
PI
AIU1
dO1
AIU2
OA01
...
OA10
Possible assignment for the Function block analog input.
[No] (nO): Not assigned
[Al1] (A11): Analog input A1
[Al2] (A12): Analog input A2
[Al3] (A13): Analog input A3
[I motor] (OCr): Motor current
[Motor freq.] (OFr): Motor speed
[Ramp. out] (OrP): Ramp output
[Motor torq.] (trq): Motor torque
[Sign torque] (Stq): Signed motor torque
[Sign ramp] (OrS): Signed ramp output
[PID ref.] (OPS): PI(D) reference
[PID feedbk] (OPF): PI(D) feedback
[PID error] (OPE): PI(D) error
[PID output] (OPI)
: PI(D) integral
[Mot
. power] (OPr): Motor power
[Mot. thermal] (tHr): Motor thermal state
[Drv thermal] (tHd): Drive thermal state
[Torque 4Q] (tqMS): Signed motor torque
[+/-Speed] (UPdt): Up/Down function is assigned by Lix
[+/-spd HMI] (UPdH): Up/Down function is assigned by graphic display terminal or remote display terminal
[HMI] (LCC): Graphic display terminal or remote display terminal source
[Modbus] (Mdb): Integrated Modbus
[CANopen] (CAn): Integrated CANopen®
[Com. card] (nEt): Communication option board source
[Sig. o/p frq.] (OFS): Signed output frequency
[Mot therm2] (tHr2): Motor 2 thermal state
[Mot therm3] (tHr3): Motor 3 thermal state
[Torque lim.] (tqL): Torque limitation
[Motor volt.] (UOP): Motor voltage
[RP] (PI): Pulse input
[AI virtual 1] (AIU1): Virtual analog input 1 with the jog dial
[DO1] (dO1): Analog/logical output DO1
[AI virtual 2] (AIU2): Virtual analog input 2 by the communication bus
[OA01] (OA01)
: Function blocks: Analog Output 01
...
[OA10] (OA10):
Function blocks: Analog Output 10
IA-- [Analog input x assignment]
[No] (nO)
All the Function blocks analog inputs available on the drive are processed as in the example for [IA01] (IA01) above, up to
[IA10] (IA10).
FbM- [FUNCTION BLOCKS] (continued)
FAd- [ADL CONTAINERS]
ADL containers contain Modbus logical adress of internal parameters of the drive. If the chosen adress is valid, the display shows
the parameter name instead of the adress.
LA01
ADL Container 01 3,015 to 64,299 0
LA02
ADL Container 02 3,015 to 64,299 0
LA03
ADL Container 03 3,015 to 64,299 0
LA04
ADL Container 04 3,015 to 64,299 0
LA05
ADL Container 05 3,015 to 64,299 0
LA06
ADL Container 06 3,015 to 64,299 0
LA07
ADL Container 07 3,015 to 64,299 0
LA08
ADL Container 08 3,015 to 64,299 0
Code Name / Description Adjustment range Factory setting
DRI- > CONF > FULL > FBM- > FBA-
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: [phone]-Outside Local Area: [phone]-www.stevenengineering.com