Installation manual

Monitoring Mode (MOn)
58 S1A28692 03/2010
Parameters described in this page can be accessed by:
SSt- [OTHER STATE]
List of secondary states.
This menu is visible only on graphic display terminal.
FL
PtCL
FSt
CtA
FtA
F2A
SrA
tSA
EtF
AUtO
FtL
tUn
USA
CnF1
CnF2
FLA
AnA
CFP1
CFP2
CFP3
brS
dbL
ttHA
ttLA
MFrd
MrrS
FqLA
[In motor fluxing] (FL )
[PTC Alarm] (PtCL)
[Fast stop in prog.] (FSt)
[Current Th. attained] (CtA)
[Freq. Th. attained] (FtA)
[Freq. Th. 2 attained] (F2A)
[Frequency ref. att.] (SrA)
[Motor th. state att.] (tSA)
[External fault alarm] (EtF)
[Auto restart] (AUtO)
[Remote] (FtL)
[Auto-tuning] (tUn)
[Undervoltage] (USA)
[Config. 1 act.] (CnF1)
[Config. 2 act.] (CnF2)
[HSP attained] (FLA)
[Dévirage charge]
(AnA)
[Set
1 active] (CFP1)
[Set 2 active] (CFP2)
[Set 3 active] (CFP3)
[In braking] (brS)
[DC bus loading] (dbL)
[High torque alarm] (ttHA)
[Low torque alarm] (ttLA)
[Forward] (MFrd)
[Reverse] (MrrS)
[Freq. metre Alarm] (FqLA)
dGt- [DIAGNOSTICS]
This menu is visible only on graphic display terminal.
pFH- [FAULT HISTORY]
Shows the 8 last detected faults.
dP1 [Past fault 1]
nOF
ASF
bLF
brF
CFF
CFI2
CnF
COF
CrF
CSF
dCF
dLF
EEF1
EEF2
EPF1
EPF2
FbE
FbES
FCF1
FCF2
HCF
HdF
ILF
InF1
InF2
InF3
InF4
InF6
Fault record 1 (1 is last).
[No fault] (nOF): No detected fault memorized
[Angle error] (ASF): Angle setting detected fault
[Brake control] (bLF): Brake's motor 3-phases loss
[Brake feedback] (brF): Brake contactor detected error
[Incorrect config.] (CFF): Invalid configuration at power on
[Bad conf] (CFI2): Configuration transfer detected error
[Com. network] (CnF): NET option communication interruption
[CAN com.] (COF): CANopen® communication interruption
[Capa.charg] (CrF): Load relay detected fault
[Ch.sw. fault] (CSF): Channel switching detected error
[Diff. I fault] (dCF): Differential current detected fault
[Load fault] (dLF): Dynamic load detected error
[Control EEprom] (EEF1)
: Control EEprom detected error
[
Power Eeprom] (EEF2): Power EEprom detected error
[External fault LI/Bit] (EPF1): External detected fault from LI or local link
[External fault com.] (EPF2): External interruption from communication board
[FB fault] (FbE): Function block detected error
[FB stop fly.] (FbES): Function block stop detected error
[Out. contact. stuck] (FCF1): Output contactor: closed contactor
[Out. contact. open.] (FCF2): Output contactor: opened contactor
[Cards pairing] (HCF): Hardware configuration detected error
[IGBT desaturation] (HdF): Hardware detected error
[Option int link] (ILF): Option internal link interruption
[Rating error] (InF1): Unknown drive rating
[PWR Calib.] (InF2): Unknown or incompatible power board
[Int.serial link] (InF3): Internal serial link communication interruption
[Int.Mfg area] (InF4): Invalid industrialization zone
[Internal-option] (InF6): Unknown or incompatible option board
Code Name / Description Unit
DRI- > MON- > SST-
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: [phone]-Outside Local Area: [phone]-www.stevenengineering.com