Installation manual

Monitoring Mode (MOn)
S1A28692 03/2010 61
Parameters described in this page can be accessed by:
dGt- [DIAGNOSTICS] (continued)
PFL- [CURRENT FAULT LIST]
nOF
ASF
bLF
brF
CFF
CFI2
CnF
COF
CrF
CSF
dCF
dLF
EEF1
EEF2
EPF1
EPF2
FbE
FbES
FCF1
FCF2
HCF
HdF
ILF
InF1
InF2
InF3
InF4
InF6
InF9
InFA
InFb
InFE
LCF
LFF3
ObF
OCF
OHF
OLC
OLF
OPF1
OPF2
OSF
OtFL
PHF
PtFL
SAFF
SCF1
SCF3
SCF4
SCF5
SLF1
SLF2
SLF3
SOF
SPF
SrF
SSF
tJF
tnF
ULF
USF
[No fault] (nOF): No detected fault memorized
[Angle error] (ASF): Angle setting detected fault
[Brake control] (bLF): Brake's motor 3-phases loss
[Brake feedback] (brF): Brake contactor detected error
[Incorrect config.] (CFF): Invalid configuration at power on
[Bad conf] (CFI2): Configuration transfer detected error
[Com. network] (CnF): NET option communication interruption
[CAN com.] (COF): CANopen® communication interruption
[Capa.charg] (CrF): Load relay detected fault
[Ch.sw. fault] (CSF): Channe
l switching detected error
[Diff. I fault] (dCF): Differential current detected fault
[Load fault] (dLF): Dynamic load detected error
[Control EEprom] (EEF1): Control EEprom detected error
[Power Eeprom] (EEF2): Power EEprom detected error
[External fault LI/Bit] (EPF1): External detected fault from LI or local link
[External fault com.] (EPF2): External interruption from communication board
[FB fault] (FbE): Function block detected error
[FB stop fly.] (FbES): Function block stop detected error
[Out. contact. stuck] (FCF1): Output contactor: closed contactor
[Out. contact. open.] (FCF2): Output contactor: opened contactor
[Cards pairing] (HCF): Hardware configuration detected error
[IGBT desaturation] (HdF): Hardware detected error
[Option int link] (ILF): Option internal link interruption
[Rating error] (InF1): Unknown drive rating
[PWR Calib.] (InF2): Unknown or incompatible power board
[Int.serial link] (InF3):
Intern
al serial link communication interruption
[Int.Mfg area] (InF4): Invalid industrialization zone
[Internal-option] (InF6): Unknown or incompatible option board
[Internal- I measure] (InF9): Current measurement circuit detected error
[Internal-mains circuit] (InFA): Input phase loss circuit detected error
[Internal- th. sensor] (InFb): Thermal sensor detected error (OC or SC)
[Internal-CPU] (InFE): CPU detected fault (ram, flash, task ...)
[Input contactor] (LCF): Line contactor detected error
[AI3 4-20mA loss] (LFF3): AI3 4-20 mA loss
[Overbraking] (ObF): Overbraking
[Overcurrent] (OCF): Overcurrent
[Drive overheat] (OHF): Drive overheating
[Proc.Overload Flt] (OLC): Torque overload
[Motor overload] (OLF): Motor overload
[1 output phase loss] (OPF1): Motor 1-phase loss
[3out ph loss] (OPF2): Motor 3-phases loss
[Mains overvoltage] (OSF): Oversupply detected fault
[PTC fault]
(OtFL): Motor
overheating detected error from PTCL: standard product
[Input phase loss] (PHF): Main input 1-phase loss
[LI6=PTC probe] (PtFL): PTCL detected error (OC or SC)
[Safety fault] (SAFF): Safety function trip
[Motor short circuit] (SCF1): Motor short circuit (hard detection)
[Ground short circuit] (SCF3): Direct ground short-circuit trip (hard detection)
[IGBT short circuit] (SCF4): IGBT short-circuit (hard detection)
[Motor short circuit] (SCF5): Load short-circuit during Igon load sequence (hard detection)
[Modbus com.] (SLF1): Modbus local serial communication interruption
[PC com.] (SLF2): PC Software communication interruption
[HMI com.] (SLF3): Remote terminal communication interruption
[Overspeed] (SOF): Overspeed
[Speed fdback loss] (SPF): Speed feedback loss
[Torque time-out] (SrF): Torque regulation time-out
[Torque/current lim] (SSF): Torque current limitation detected fault
[IGBT overheat] (tJF): IGBT overheating
[Auto-tuning] (tnF): Tune detected fault
[Pr.Underload Flt] (ULF
): Tor
que underload
[Undervoltage] (USF): Undervoltage
Code Name / Description Unit
DRI- > MON- > DGT- > PFL-
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: [phone]-Outside Local Area: [phone]-www.stevenengineering.com