Installation manual

Monitoring Mode (MOn)
S1A28692 03/2010 63
Parameters described in this page can be accessed by:
MOn- [1.2 MONITORING] (continued)
COd- [PASSWORD]
HMI Password.
If you have lost your code, please contact Schneider Electric.
CSt [State]
LC
ULC
Status of the drive (lock/unlock). Information parameter, cannot be modified.
[Locked] (LC): The drive is locked by a password
[Unlocked] (ULC): The drive is not locked by a password
COd
OFF
On
[PIN code 1]
Confidential code.
Enables the drive configuration to be protected using an access code.
When access is locked by means of a code, only the parameters in the [1.2 MONITORING] (MOn-) and
[1.1 SPEED REFERENCE] (rEF-) menus can be accessed. The MODE key can be used to switch between menus.
Note: Before entering a code, do not forget to make a careful note of it.
[OFF] (OFF): No access locking codes.
- To lock access, enter a code (2 to 9,999). The display can be incremented using the jog dial. Then press ENT. [ON] (On)
appears on the screen to indicate that access has been locked.
[ON] (On): A code is locking access (2 to 9,999).
- To unlock access, enter the code (incrementing the display using the jog dial) and press ENT. The code remains on the
display and access is unlocked until the next time the drive is turned off. Access will be locked again the next time the drive
is turned on.
- If an incorrect code is entered, the display changes to [ON] (On), and access remains locked.
Access is unlocked (the code remains on the screen).
- To reactivate locking with the same code when access has been unlocked, return to [ON] (On) using the jog dial and then
press ENT. [ON] (On) remains on the screen to indicate that access has been locked.
- To lock access with a new code when access has been unlocked, enter the new code (increment the display using the jog
dial) and then press ENT. [ON] (On) appears on the screen to indicate that access has been locked.
- To clear locking when access has been unlocked, return to [OFF] (OFF) using the jog dial and then press ENT.
[OFF] (OFF) remains on the display. Access is unlocked and will remain so until the next restart.
COd2 [PIN code 2]
g
Confidential code 2. Visible if [3.1 ACCESS LEVEL] (LAC) is set to [Expert] (Epr).
OFF
On
8888
The value [OFF] (OFF) indicates that no password has been set [Unlocked] (ULC).
The value [ON] (On) indicates that the drive configuration is protected and an access code must be entered in order to unlock it.
Once the correct code has been entered, it remains on the display and the drive is unlocked until the next time the power supply
is disconnected.
PIN code 2 is an unlock code known only to Schneider Electric Product Support.
ULr [Upload rights]
ULr0
ULr1
[Permitted] (ULr0): Means that SoMove or the graphic display terminal can save the whole configuration (password,
protections, configuration). When the configuration is edited, only the non protected parameters will be accessible.
[Not allowed] (ULr1): Means that SoMove or the graphic display terminal cannot save the configuration
dLr
dLr0
dLr1
dLr2
dLr3
[Download rights]
[Locked drv] (dLr0): Locked drive: means that the configuration can be downloaded only in a locked drive which configuration
has the same password. If the passwords are different, download is not permitted.
[Unlock. drv] (dLr1): Unlocked drive: means that the configuration can be downloaded only in a drive without active password
[Not allowed] (dLr2): Not allowed: the configuration cannot be downloaded
[Lock/unlock] (dLr3): Lock. + Not: download is permitted following case 0 or case 1
g
These parameters only appear if the corresponding function has been selected in another menu. When the parameters can
also be accessed and adjusted from within the configuration menu for the corresponding function, their description is detailed
in these menus, on the pages indicated, to aid programming.
T
Parameter that can be modified during operation or when stopped.
Code Name / Description Unit
DRI- > MON- > COD-
Courtesy of Steven Engineering, Inc.-230 Ryan Way, South San Francisco, CA 94080-6370-Main Office: [phone]-Outside Local Area: [phone]-www.stevenengineering.com