Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Charger Specifications
975-0638-01-03 6–3
Charger Specifications
NOTE: All charging specifications are at nominal conditions: ambient
temperature of 77 °F (25 °C), split-phase 120/240 VAC, 60 Hz unless otherwise
specified.
No-load power draw (Inverter
On)
21 W26 W27 W
Low battery voltage shutdown
cut-off
(other values selectable)
21.0 V
(default)
21.0 V
(default)
42.0 V
(default)
High battery voltage shutdown
cut-off
(other values selectable)
33.0 V
(default)
33.0 V
(default)
62.0 V
(default)
DC Input
SW 2524 120/240 SW 4024 120/240 SW 4048 120/240
DC Output
SW 2524 120/240 SW 4024 120/240 SW 4048 120/240
Maximum output current 65 A 90 A
a
45 A
Nominal output voltage 24 VDC 24 VDC 48 VDC
Charging output voltage
operation range
b
12.0–
32.0 VDC
12.0–
32.0 VDC
24.0–
64.0 VDC
Equalization cycle Automatic,
Manual by
SCP
Automatic,
Manual by
SCP
Automatic,
Manual by
SCP
Optimal charging efficiency 90% 90% 92%
Dead battery charge voltage > 12.0 VDC > 12.0 VDC > 24.0 VDC
Charging methods (two
settings)
Three-stage charge (Bulk, Absorption, Float)
[default]
Two-stage charge (Bulk, Absorption)
Without a battery temperature
sensor (three settings)
Cool 50 °F (10 °C)
Warm 77 °F (25 °C) [default]
Hot 104 °F (40 °C)