Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Physical Specifications
975-0638-01-03 6–5
Physical Specifications
Environmental Specifications
SW 2524 120/240 SW 4024 120/240 SW 4048 120/240
L × W × H
15.2×13.5×7.6 in
(387×343×197 mm)
15.2×13.5×7.6 in
(387×343×197 mm)
15.2×13.5×7.6 in
(387×343×197 mm)
Unit Net
Weight
50.7 lbs. (23 kg) 67.2 lbs. (30.5 kg) 67.2 lbs. (30.5 kg)
All Models
Nominal ambient temperature 77 °F (25 °C)
Operating temperature range
–4 to 140 °F (–20 to 60 °C)
starts derating above 77 °F (25 °C) (see following graph)
Storage temperature range –40 to 185 °F (–40 to 85 °C)
Humidity: Operation/Storage 95% RH, non-condensing
Ingress protection rating Indoor only, IP 20
Pollution degree 3
Over voltage category (AC mains) CAT III
Altitude: Operating 6,562 ft. (2,000 m)
Mounting wall mount using installation bracket
Figure 6-1 Output Power versus Temperature Derating Graph
-20 -10 0 5 10 15 20 25 30 35 40 45 50 55 60 °C
-4 14 32 41 50 59 68 77 86 95 104 113 122 131 140 °F
3750
3500
3250
3000
2750
2500
2250
2000
1750
1500
W
SW 4024 120/240
SW 2524 120/240
Full power at ambient
3400W
2800W
2500W
3000W
3800W
3600W
3400W
3200W
SW 4048 120/240
2750W