Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conextâ„¢ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
975-0638-01-03 IX-1
Numerics
2-stage charge mode 4-17
A
ABS Finish 3-13
Absorption
3-13
absorption charging stage
4-16
AC bypass
3-6
AC settings menu
description
4-24
AC Support
3-13
Ac support menu
description
4-25
ACGood
3-13
Adjustable frequency
1-3
Advanced menu
4-5
automatic generator start
4-11
B
battery equalization 4-18
Battery power
3-5
battery type
4-7, 4-13, 4-14
Bulk
3-13
bulk charging stage
4-16
C
Charger Block, start and stop 4-19
charger settings menu
description
4-13
charging
battery temperature sensor
1-4
built-in charge formulas
1-4
equalization
1-4
load management
1-4
custom battery menu
4-20, 4-23
D
default settings, restoring 4-35
Down arrow button
3-9
E
Enter button 3-9
equalize charging
4-18
equalize mode
3-13
Exit button
3-9
F
fault/warning LED Xanbus System Control Panel) 3-
9
Float
3-13
float charging stage
4-17
H
High surge capacity 1-3
I
Information about Your System form 1-ii
Invert
3-13
inverter
serial number
1-ii
Inverter Block, start and stop
4-12
inverter settings menu
description
4-7, 4-9
K
keypress for system standby mode 3-10
L
LdSenseActv 3-13
Load Shave
3-13
M
meters screen 3-15
Multiple Unit Configuration
multi unit menu screen
4-32
Multi-stage charging
1-3
N
no float charging stage 4-17
NoFloat
3-13
P
Power factor correction 1-3
proof of purchase
1-ii
Q
qualifying AC 3-13
R
restore default settings 4-35
Index