Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Inverter Operation Using the Front Panel
975-0638-01-03 3–5
Operating Limits for Inverter Operation
Temperature The Conext SW series of inverter/chargers will operate at rated
power continuously at 77 °F (25 °C) with some models capable of continuous
operation at much higher ambient temperature. However, the continuous power
rating at elevated ambient temperature may differ between models. See
“Environmental Specifications” on page 6–5 for full details. In higher ambient
temperatures, if the loads draw full power for an extended period of time, the unit
may shut down to protect itself against overheating.
Surge Power The Conext SW series of inverter chargers feature a surge rating
of 200% of rated power for five seconds at 77 °F (25 °C). See “Inverter
Specifications” on page 6–2 for full details. Operating the inverter/charger in
conditions outside of normal rated power and temperature limits, however, will
result in thermal shutdown and/or significantly decreased performance. See
“Inverter Specifications” on page 6–2 for information on continuous operation at
higher than rated power.
Difficulty on starting loads The inverter/charger should be able to operate all
AC loads rated at or below its power rating. Some high horsepower induction
motors used in pumps and other motor-operated equipment require very high
surge currents to start, and the inverter/charger may have difficulty starting these
loads.
If you have problems starting certain loads, ensure that:
• The battery connections are tight and clean.
• The DC cabling is no longer than the recommended length. Refer to the
Conext SW Inverter/Charger Installation Guide for this information.
• The AC wiring is of recommended size. Refer to the Conext SW Inverter/
Charger Installation Guide for this information.
• The battery is of sufficient capacity and is fully charged.
Split-phase output during invert mode and AC bypass The Conext SW always
yields a split-phase output when inverting and during AC bypass.
• A split-phase input through L1 and L2 yields a split-phase output of L1
and L2.
• Single-phase input through L1 yields a split-phase output of L1 and L2.
• A single-phase input through L2 does not produce any output. Only the
input in Line 1 is capable of qualifying the AC coming from the power
source.