Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Operation
3–14 975-0638-01-03
Viewing Other Screens
This section describes the next level of screens and menus on the SCP.
Select Device
Menu
The Select Device menu displays a list of Xanbus-enabled devices in the
system, including the Conext SW and the SCP. The Select Device menu is
where you can access the Setup menus for each device in the system. The
length of the Select Device menu depends on how many Xanbus-enabled
devices are installed.
The Select Device menu also contains the Clock menu (where the time and
date are set) and the System Settings menu (where system-level settings can
be configured). The System Settings, SCP, and Clock menus are always
available from the Select Device menu, regardless of the number of Xanbus-
enabled devices installed.
To display the Select Device menu:
u While viewing the System Status screen, press Enter.
Device Setup
Menus
Device Setup menus display status information (on the Meters screen) and
changeable settings. Changeable settings are identified by the square brackets
[ ] around values in the right-hand column.
To display the Setup menu for a device:
u Highlight the device name on the Select Device menu by using the up and
down arrow buttons, and then press Enter on the highlighted device.
-Or-
From the Home screen menu, simply press Enter.
When a particular device is selected, it is possible to change its settings and operate
the device using the Device Setup menu screen. For more information on how to
operate the Conext SW, see “Changing Operational Settings” on page 3–16.
Figure 3-5 Selecting a Device Setup Menu
Select Device
System Settings
CSW4024
Device 2
Device 3
Device n
XW SCP
Clock
CSW4024 00:Setup
Meters
Inverter
Search Mode
Charger
Force Chg State
Equalize
Mode
Clear Faults/Warnings
View Device Info
Basic Settings
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Operating]
Select device from list,
and then press Enter to
view device Setup menu
Select Device menu Inverter/Charger Setup menu
NOTE: The SCP only displays four lines of
the Setup menu at one time. To view
additional settings, press the down arrow
button.