Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Inverter/Charger Operation using the System Control Panel (SCP)
975-0638-01-03 3–15
Meters Screen The Meters screen displays total system power production, generator voltage
and current status, and load voltage and current status.
To view the Meters screen:
u On the Conext SW Setup menu highlight Meters, and then press Enter.
Figure 3-6 Viewing the Meters Screen
Table 3-3 Meters Screen
Screen Item Description
Mode Operating state of the Conext SW. See also “Conext SW Home
Screen States” on page 3–13.
Battery Displays battery voltage, charging current and battery
temperature. The battery temperature comes from the BTS,
connected to the Conext SW. If the BTS is not installed, Battery
shows as N/A (not available).
Load Displays power consumption (watts), voltage, and current
(amps) supplied to the AC loads.
AC Quality Displays the quality of the AC input. A good quality AC input
generally means that it falls between the high and low voltage
range set in “AC Settings” on page 4–24.
AC In L1 AC input current, voltage, and frequency connected to the
Conext SW AC INPUT L1 terminal.
AC In L2 AC input current, voltage, and frequency connected to the
Conext SW AC INPUT L2 terminal.
AC In L1L2 Combined L1 and L2 input voltage and frequency.
CSW4024 00: Setup
Meters
Inverter
Search Mode
Charger
Force Chg State
Equalize
Mode
Clear Faults/Warnings
View Device Info
Basic Settings
[Enabled]
[Disabled]
[Enabled]
[Disabled]
[Operating]
CSW4024 00: Meters
Mode
Battery
Load
AC Quality
AC In L1
AC In L2
AC In L1L2
ACGood
23.9V 0.0A N/A
450W 240V 3.7A
L1L2 Good
3.8A 120V 60Hz
3.7A 120V 60Hz
240V 60Hz