Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Configuration via SCP
4–4 975-0638-01-03
Viewing the Basic and Advanced Settings Menus
Basic Settings
menu
The Conext SW configuration settings can be viewed in Basic and Advanced
formats. The Basic Settings include configuration items you may have to adjust
routinely or as part of initial setup. The Basic Settings option appears by default
on the Setup menu screen.
The Conext SW Basic settings include menus for configuring:
• Battery type setting (see page 4–7).
• Battery capacity setting (see page 4–7).
• Maximum charging rate setting (see page 4–7).
• Charging cycle setting (see page 4–7).
• Recharge volts setting (see page 4–7)
• AC priority setting (see page 4–7).
• AC In Breaker settings (see page 4–7).
• Low battery cutout setting (see page 4–7).
To view the Basic Settings menu:
u From the Setup menu, scroll to the bottom of the screen to highlight Basic
Settings and press Enter. See Figure 4-2.
To select and change a configurable setting:
1. On the desired configuration menu, press the up arrow or down arrow button
to highlight the setting you want to change.
2. Press Enter to highlight the current value of the setting.
3. Press the up arrow or the down arrow button to change the value. Hold down
the button to scroll through a large range of values quickly.
The previously set value appears with an asterisk (*) beside it.
4. Press Enter to select the value.
5. If you have another setting to change, return to step 1.
Or
If you have no more settings to change, press Exit until the SCP displays the
desired screen or menu.
Figure 4-1 Selecting Basic Settings
CSW4024 00: Setup
Meters
Inverter
Search Mode
Grid Support
[Enabled]
[Disabled]
[Disabled]
CSW40
Mode
Clear Faults/Warnings
View Device Info
Basic Settings
[Operating]
CSW4024 00: Basic
Batt Type
Batt Capacity
Max Chg Rate
Charge Cycle
ReCharge Volts
AC In Breaker
Low Batt Cut Out
[Flooded]
[220Ah]
[80%]
[3Stage]
[25.0V]
[30.0A]
[21.0V]
24 00: Setup