Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Configuring Basic Settings
975-0638-01-03 4–7
Configuring Basic Settings
An overview of the Conext SW Basic Settings menu structure is shown below.
NOTICE
EQUIPMENT DAMAGE
Transition the Conext SW to Standby mode
a
(see page 3–10) before making
changes to the device settings. You may transition the unit back to Operating
mode after enacting the changes.
Failure to follow these instructions can damage equipment.
a.Critical loads will lose power and disconnect from the grid (or generator) when the Conext
SW transitions to Standby mode.
Figure 4-3 Menu Map of the Conext SW Basic Settings
[*Flooded] [Gel] [AGM]
[*250Ah] [50Ah] to [1000Ah]
[*80%] [10%] to [100%]
[*3Stage] or [2StgNoFloat]
[*25.0V] [22.0V]to [29.0V]
[*30.0A] [5.0A]to [30.0A]
[*21.0V] [20.0V]to [24.0V]
CSW4024 00: Basic
Batt Type
Batt Capacity
Max Chg Rate
Charge Cycle
ReCharge Volts
AC In Breaker
Low Batt Cut Out
[Flooded]
[220Ah]
[80%]
[3Stage]
[25.0V]
[30.0A]
[21.0V]
Follow procedures on “To select and change a configurable setting:” on
page 4–4 to change the settings.
Table 4-1 Setting Defaults and Ranges
Model 24-volt Models 48-volt Model
Setting Default Min Max Default Min Max
Batt Type Flooded Flooded, Gel,
AGM, Custom
Flooded Flooded, Gel,
AGM, Custom
Batt Capacity 250Ah 50Ah 100Ah 250Ah 50Ah 1000Ah
Max Chg Rate 100% 10% 100% 100% 10% 100%
Charge Cycle 3Stage 3Stage,
2StgNoFloat
3Stage 3Stage,
2StgNoFloat
ReCharge Volts 25.0V 22.0V 29.0V 50.0V 44.0V 58.0V
AC In Breaker 30A 5A 30A 30A 5A 30A