Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Configuring Advanced Settings
975-0638-01-03 4–13
The Inverter setting must be initially Enabled in order for the Inverter Block to
work as intended. The Inv Block Start setting disables inverter function if the
inverter is initially enabled and then Inv Block Stop enables the inverter
function. However, if the Inverter setting is initially Disabled when Inv Block
Start commences, then the succeeding Inv Block Stop will not enable inverter
function automatically. The inverter will remain disabled.
Setting the Inv Block Start and Inv Block Stop to the same time disables
Inverter Block. Disabling Inverter Block means that inverting is allowed to occur
at any time when the right conditions for inverting exist.
Charger Settings Menu
The Charger Settings menu provides options for configuring the Conext SW to
operate from your battery bank.
Figure 4-5 Charger Settings Menu Screen
Table 4-5 Setting Defaults and Ranges
Model 24-Volt Models 48-Volt Model
Setting Default Min Max Default Min Max
Batt Type Flooded Flooded, Gel,
AGM, Custom,
LithiumIon
Flooded Flooded, Gel,
AGM, Custom,
LithiumIon
Custom Settings See page 4–20. See page 4–20.
LithiumIon
Settings
See page 4–22. See page 4–22.
Batt Capacity See page 4–7. See page 4–7.
Max Chg Rate 100% 10% 100% 100% 10% 100%
CSW4024 00: Chg
Batt Type
Custom Settings
LithiumIon Settings
Batt Capacity
Max Chg Rate
Charge Cycle
Default Batt Temp
ReCharge Volts
Absorb Time
Auto Chg Enable
Chg Block Start
Chg Block Stop
[Flooded]
[220Ah]
[100%]
[3-Stage]
[Warm]
[25.0V]
[180min]
[Enabled]
[hh:mm AM]
[hh:mm AM]
CSW4024 00: Adv
Inverter Settings
Charger Settings
AC Settings
AC Support
Multi Unit Config
Restore Defaults
Adv Features
[*80%] [10%] to [100%]
[*220Ah] [50Ah] to [1000Ah]
[*3-Stage] or [2StgNoFloat]
[*Warm] [Hot] [Cold]
[*25.0V] [22.0V] to [29.0V]
[*180min] [1min] to [480min]
[*Enabled] or [Disabled]
[*Flooded] [Gel] [AGM] [Custom] [LithiumIon]
Follow procedures on “To select and change a configurable setting:” on page 4–6 to
change the settings.