Conext SW4048 4,000W 48V Installation
Table Of Contents
- Conext™ SW Inverter/Charger
- Exclusion for Documentation
- Document Number: 975-0638-01-03 Revision: Date: 5-2020
- Contact Information solar.schneider-electric.com
- Information About Your System
- About This Guide
- Important Safety Instructions
- Safety Information
- Precautions When Working With Batteries
- FCC Information to the User
- Introduction
- Materials List
- Key Features
- Key Features Explained
- Basic Protection Features
- Grid-interactive and Other Features
- Load Shaving
- AC Support
- Grid-Interactive Delay Feature
- AC Coupling
- AC Couple Smart Charge
- Storing the State of the Inverter Mode
- NoLoadVD
- Low Battery Cut Out Hysteresis
- LBCO Delay
- Lithium Ion Battery Type
- Components and Mechanical Features
- System Components
- Xanbus System
- Xanbus-enabled Products and Other Accessories
- Conext SW Inverter/Charger Mechanical Features
- Conext SW Front and Side Panels
- Operation
- Start Up Behavior
- Inverter Operation Using the Front Panel
- Operating Limits for Inverter Operation
- Operating Limits for Charger Operation
- Inverter/Charger Operation using the System Control Panel (SCP)
- SCP Features
- Using the Standby Button
- SCP Navigation
- Changing Operational Settings
- Configuration via SCP
- Viewing the Firmware Revision Number
- Setting the Time and Date
- Viewing the Basic and Advanced Settings Menus
- Configuring Basic Settings
- Configuring Advanced Settings
- Inverter Settings Menu
- Charger Settings Menu
- AC Settings
- AC Support Settings
- Multi Unit Config Menu
- Restoring Factory Default Settings
- Advanced Features Menu
- Configuration Sheet
- Troubleshooting
- General Troubleshooting Guidelines
- Inverter Applications
- View Device Info Logs
- Troubleshooting the Conext SW via the SCP
- Fault Detection Types
- Warning Types
- Specifications
- Inverter Specifications
- Charger Specifications
- AC Transfer Specifications
- Physical Specifications
- Environmental Specifications
- Regulatory
Configuration via SCP
4–22 975-0638-01-03
LithiumIon Battery Settings Menu
WARNING
BATTERY TYPE HAZARD
When using Lithium Ion batteries, ensure that the battery pack being used
includes a certified Battery Management System (BMS) with safety controls.
Failure to follow this instruction can result in property damage, death
or serious injury.
Figure 4-7 LithiumIon Settings Menu Screen
Table 4-13 Setting Defaults and Ranges
Model 24-Volt Models 48-Volt Model
Setting Default Min Max Default Min Max
Control 3-Stage Ext BMS,
2-Stage,
3-Stage
3-Stage Ext BMS,
2-Stage,
3-Stage
Bulk Voltage 29.0V 28.2V 32.5V 58.0V 56.2V 65.0V
Max Bulk
Current
90A 15A 90A 45A 10A 45A
Absorb Voltage 29.0V 20.0V 32.5V 58.0V 40.0V 65.0V
Max Absorb
Current
90A 15A 90A 45A 10A 45A
Float Voltage 26.8V 23.6V 32.0V 53.6V 47.2V 64.0V
Max Float
Current
90A 1A 90A 45A 1A 45A
DisChgImax 150% 20% 500% 150% 20% 500%
CSW4024 00: LithiumIon
Control
Bulk Voltage
Max Bulk Current
Absorb Voltage
Max Absorb Current
Float Voltage
Max Float Current
DisChgImax
DisChgImax Timer
[3-Stage]
[29.0V]
[90A]
[29.0V]
[90A]
[26.8V]
[90A]
[150%]
[10s]
CSW4024 00: Chg
Batt Type
LithiumIon Settings
Batt Capacity
Max Chg Rate
Charge Cycle
[LithiumIon]
[250Ah]
[100%]
[3-Stage]
Follow procedures on “To select and change a configurable setting:” on page 4–6 to
change the settings.
LithiumIon Settings appears only
when Batt Type is set to LithiumIon.