Installation Manual

Contents
xviii 975-0239-01-01 Rev J
This manual is for use by qualified personnel only
5 Conext XW+ Inverter/Charger Accessories Installation
Conext Combox Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–2
Conext System Control Panel Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–2
Installing the SCP via the Xanbus Network - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–3
Replacing the Inverter Information Panel with the SCP - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–4
Verifying the Installation - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - 5–7
Specifications
Electrical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–2
Grid-tie Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–3
Response to Abnormal Grid Conditions - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–4
Conext XW+ Overload Capability - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–5
Output Power Versus Ambient Temperature - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–8
Conext XW+ Efficiency - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–9
Inverting Efficiency (Typical) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–9
Charging Efficiency (Typical) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–10
Charging Efficiency Power Factor - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–11
Mechanical Specifications - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–12
Accessories- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - A–13
Wiring Diagrams
Single-Inverter System (Backup Only) Without a Conext XW+ Power Distribution Panel - - - - - - - B–3
Single-Inverter System (Backup Only) With a Conext XW+ Power Distribution Panel - - - - - - - - - B–4
Single-Inverter System Renewable Energy (Solar)- - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - B–5
Dual-Inverter System Renewable Energy (Solar) - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - B–6
Split-Phase to Single-Phase Conversion Instructions
Converting 120 V/240 V Split-Phase to 120 V Single-Phase - - - - - - - - - - - - - - - - - - - - - - - - - - - C–2
Installation Tools and Materials - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C–3
Disconnecting Power Sources - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C–4
AC Access Panel Removal - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C–5
Reconfiguring the Secondary Transformer Wires on X1 and X2 Connectors - - - - - - - - - - - - C–7
Reconfiguring the AC Ports on the Load, AC1, and AC2 Connectors - - - - - - - - - - - - - - - - - C–9
Upgrading the Firmware - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C–10
Updating the Label - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - - C–11
XW-NA-Install.book Page xviii Wednesday, August 12, 2015 2:23 PM