Mission FT 4WD Conversion Instructions

ManualsBrandsSchumacher ManualsCars & TrucksMission FT 4WD Conversion Kit

Table Of Contents

Leave loose for now, this

will be adjusted later.

Add rear diff supports.

Use rear option.

Reverse the motor mount

and fit in rear position.

Fit the rear belt.

Remove the rear trackrods

and fit block to the rear of

the chassis.

The 4WD conversion now includes a spool and double joint driveshafts to maximise

performance. The instructions in the kit manual (pages 40-44) are now obsolete. These

instructions MUST be used instead.

M3 x 8

x 2

Reuse Kit Part(s)

U8111 4WD Conversion Step 1

4WD Conversion Step 6

S1593 Page 1

U8111 4WD Conversion

4WD Conversion Step 2

4WD Conversion Step 4

Summary of content (6 pages)

PAGE 1
U8111 4WD Conversion The 4WD conversion now includes a spool and double joint driveshafts to maximise performance. The instructions in the kit manual (pages 40-44) are now obsolete. These instructions MUST be used instead. U8111 4WD Conversion Step 1 Add rear diff supports. x2 M3 x 8 4WD Conversion Step 2 Use rear option. Reuse Kit Part(s) Reuse Kit Part(s) Remove the rear trackrods and fit block to the rear of the chassis.
PAGE 2
U8111 4WD Conversion Step 10 Fit the diff in the rear. Fit the spool in the front. U3808 - Assembled Spool Check the transmission rotates freely. U3510 Reuse Kit Part(s) NOTE The diff shim MUST be on this side. x3 CR 52 0 M3 x 6 U4869 NOTE The fences MUST be oriented this way. U3809 Reuse Kit Part(s) x2 ø10 x ø15 x 4 Reuse Kit Part(s) NOTE The shape of the spool axle. The pulley MUST be fitted this side. Reuse Kit Part(s) Reuse Kit Part(s) Reuse Kit Part(s) x1 SHIM ø10 x ø12.5 x 0.
PAGE 3
U8111 4WD Conversion Step 21 Front Left Quarter The flat must face the grub screw. 0 52 CR x1 M3 x 2 Reuse Kit Part(s) x1 NOTE The 5x10x3 bearing should only be used with the double joint driveshaft. 4WD Conversion Step 22 ø5 x ø10 x 3 Front Right Quarter The flat must face the grub screw. 0 52 CR x1 M3 x 2 Reuse Kit Part(s) x1 NOTE The 5x10x3 bearing should only be used with the double joint driveshaft.
PAGE 4
U8111 4WD Conversion Step 25 Rear Left Quarter Reuse Kit Part(s) x1 O’ring ø9 x 1.0 The flat must face the grub screw. Reverse the hub carrier. Fit rear driveshaft (Kit front). ‘L’ hub carrier. NOTE See Page 16 for hub height setting. ø1.5 x 9.8 x1 Reuse Kit Part(s) 4WD Conversion Step 26 0 x1 M3 x 2 52 CR Rear Right Quarter Reverse the hub carrier. Fit rear driveshaft (Kit front). NOTE See Page 16 for hub height setting. The flat must face the grub screw.
PAGE 5
U8111 4WD Conversion Step 27 Fit rear trackrods. NOTE See Page 17 for turnbuckle assembly. The length of the turnbuckle should be set to 27.00mm Reuse Kit Part(s) 4WD Conversion Step 28 x2 Reverse the servo mount. M3 Thread Insert NOTE See Page 18 for assembly instructions. 4WD Conversion Step 29 Reuse Kit Part(s) Reuse Kit Part(s) Reverse the servo in the car.
PAGE 6
U8111 4WD Conversion Step 33 Reuse Kit Part(s) NOTE See Page 20 for turnbuckle assembly. 4WD Conversion Step 41 NOTE When in the 4wd configuration, the Mission FT can fit full size stick LiPo’s, by moving the LiPo mounts to the outer positions. Reuse Kit Part(s) Reuse Kit Part(s) Reuse Kit Part(s) 4WD Conversion Rear Belt Tensioner x1 M3 x 12 x1 x2 M3 Nyloc Flanged ø4 x ø8 x 3 Page 6 M3 x 16 x1 NOTE Use the layshaft mount to set the front belt tension, then set the rear belt tension.