212 Schwinn® Recumbent Exercise Bike Parts List Full Size Hardware Chart Product Illustration Assembly Instructions
FITNESS SAFEGUARDS AND WARNINGS Before starting any exercise program, consult with your physician or health professional. He or she can help establish the correct exercise frequency, intensity (target heart rate zone) and time appropriate for your particular age and condition. The following 3 warnings listed below are also located on the computer console mast of the exercise bike. Failure to follow any of these safeguards may result in injury or serious health problems.
• • Replace Warning Label if damaged, illegible, or removed. We recommend that a minimum distance of 1 meter (39 inches) surrounding the bike is kept clear of all obstructions, including children, bystanders, and pets.
Parts List Check __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ Quantity 1 1 4 1 15 4 1 1 1 1 1 4 1 1pr 19 1 1 1 1 1 1 1 1 8 1 1 1pr 8 1 Description Computer Handlebars Computer Screws Handlebar Post Allen Bolt 8x1.
Hardware Chart Stage#1 Screws M8xP1.25x16mm Stage#2 Allen Bolt M8xP1.25x16mm Flat Washer ? 8*? 16*2T Screws M5x14L Stage#4 Stage#3 Flat Washer ? 8*? 16*2T Screws M8xP1.25x Stage#6 Screws M8xP1.25x16mm Stage#5 Flat Washer ? 8*? 16*2T mm Screws M8xP1.25x mm Stage#10 Flat Washer ? 8*? 16*2T Screws M8xP1.25x16mm Flat Washer ? 8*? 16*2T Stage#8 Screwdriver Allen Key Allen Bolt M8xP1.25x16mm Note: Please verify you have all correct parts and quantities before assembling unit.
212 Assembly Drawing with Reference Numbers
Replacement Parts List Reference # __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ __ 1 2 3 4 5 6 7 8 10 11 12 14 15 16 17 18 19 20 21 22 23 25 26 27 28 29 72 Description Computer Handlebars Computer Screws Handlebar Post Allen Bolt 8x1.
Instructions IMPORTANT!: To ensure ease of assembly please verify the size and quantity of all the required assembly hardware and parts with the enclosed parts list and full size hardware chart. Each step of the assembly process has been broken down into 6 easy-to-follow stages. Please take just a few moments to read over these instructions to familiarize yourself with the process to make assembly quick and trouble-free.
Step 3: Attach SEAT (#23) to SEAT FRAME (#26) with 4 ALLEN BOLTS 45mm (#25) and 4 WASHERS (#15). Tighten Bolts. Step 4: Attach SEAT BACK (#27) to SEAT FRAME (#26) with 4 ALLEN BOLTS 45mm (#25) and 4 WASHERS (#15). Tighten Bolts.
Assembly Stage #2 Attach Rear Stabilizer and Seat Rail to Seat Assembly Assembly hardware required: (4) M8 Allen Bolts 16mm (item #5) (4) Flat Washers Ø8 * Ø16 * 2T (item#15) (2) Flat Head Screws (item #12) Step 5: Attach the REAR STABILIZER (#17) to the SEAT RAIL POST (#16) with 2 FLAT HEAD SCREWS (#12). Tighten bolts. Step 6: Attach SEAT RAIL (#18) to SEAT RAIL POST (#16) with 4 FLAT WASHERS (#15) and 4 ALLEN BOLTS (#5). Tighten bolts Step 7: Insert SEAT PIN ADJUSTMENT KNOB (#3) into SEAT FRAME (#8).
Assembly Stage #3 Attach Front Stabilizer Tube and Pedals to Main Unit Assembly Hardware Required: (2) Flat Head Screws (item #12) Step 8: Attach FRONT STABILIZER TUBE (#11) to the MAIN UNIT (#13) with 2 FLAT HEAD SCREWS (#12). Tighten Bolts with provided wrench. Step 9: Attach RIGHT PEDAL (#14) to the right crank arm on the MAIN UNIT (#31). Thread the pedal onto the crank arm and then tighten with pedal wrench. Attach LEFT PEDAL (#14) to the left crank arm on the MAIN UNIT (#13).
Assembly Stage #4 Attach Seat Rail to Main Unit Assembly Hardware Required: (3) Allen Bolts 16 mm long (item #5) (3) Flat Washers (item #15) Step 10: Attach the SEAT RAIL HR WIRE (#19) to the LOWER HR WIRE (#10). Carefully slide the seat rail assembly onto the receiver on the MAIN UNIT (#13). CAUTION! Be careful not to pinch the heart rate wires between the seat rail and the receiver on the main unit. Failure to do so could cause damage to the wires and cause the heart rate feature not to function.
Assembly Stage #5 Attach Handlebar Assembly and Run Cabling Through Handlebar Post Assembly Hardware Required: NONE Step 11: Slide the HANDLEBAR ASSEMBLY (#2) into the receiver on the HANDLEBAR POST (#4). Slide the threaded post into the slider tube and attach the HANDLEBAR ASSEMBLY SLIDER TUBE (#2) and the HANDLEBAR POST (#4) by threading the ADJUSTMENT KNOB (#21) and the SMALL FLAT WASHER (#22) into the threaded post. Place the end cap on the end of the slider tube on the HANDLEBAR ASSEMBLY (#2).
Assembly Stage #6 Attach Console Mast to Main Unit Assembly Hardware Required: (4) Allen Bolts 16 mm long (item #5) (4) Curved Washers (item #6)
(4) Computer Screws (item #3) Step 13: Before sliding the HANDLEBAR POST (#4) onto the MAIN UNIT (#13), attach both HR CABLES (#7 & #10) as well as the COMPUTER CABLE (#8 & #9). Slide the HANDLEBAR POST (#4) onto the MAIN UNIT (#13). Fasten with 4 BOLTS (#22) and 4 CURVED WASHERS (#19). Tighten with provided Allen wrench. Step 14: Attach UPPER COMPUTER CABLE (#7) and HR CABLE (#8) to under side of COMPUTER (#1).
Troubleshooting the Schwinn 212 Recumbent Exercise Bike TIP: Use assembly diagram(s) as reference when troubleshooting unit. PROBLEM: Computer will not start, function, or is blank… (SOLUTION): 1. Ensure the batteries the unit is plugged into a 110v outlet. 2. Check the wiring connections and connector orientation made to the computer. 3. Confirm that wiring (cable assembly) has not been damaged 4. If computer still fails to start please call 1.800.864.1270 for assistance.