Owner's Manual

ManualsBrandsScosche ManualsAudio accessories & installationDash and Wiring Kit

ITCCR01B

IN-DASH

INSTALLATION

FOR

2015-UP

CHRYSLER

300

ISO

DOUBLE

DIN

WITH

POCKET

RELOCATION

PANEL

KIT

*DASH

MODIFICATION

REQUIRED

(See

page

3)*

Parts

List:

1. UAC Top Panel (7825)

2. UAC Module

3. Narrow Pocket (7823)

4. Lower Radio Panel (7826)

•

Note:

Vents

Knobs

Analog

Clock

are

retained

from

OEM

panel.

Aftermarket

radio

NOT

included.

Tools

uired:

•

PRT

Panel

Removal

Tool

•

Screwdriver

•

Cutting

Tool

-----1

•

----4

Designed

Engineered

U.S.A.

Custom

Manufactured

China

:_ NOTICE:

Extremely high temperatures may

temporarily affect the display. Normal

=--

operation

resume once the unit cools.

INTRODUCTION/PRELIMINARY

This premium installation kit is for 2015-UP Chrysler 300 vehicles. Included are all the parts you need

to mount your car stereo or CD player into your vehicle's dash. Refer to individual instruction in this

manual to remove your vehicle's factory radio and assemble the kit.

*Dash

Modification

See

page

CAUTION: DISCONNECT YOUR VEHICLE NEGATIVE BATTERY

TERMINAL

BEFORE THE

INSTALLATION

HELP PREVENT ELECTRICAL DAMAGE. WE

RECOMMEND

THE USE

VOLT/

OHM

METER OVER A TEST

LIGHT

TO CHECK WIRING. A TEST

LIGHT

GROUNDED

WIRE PROBE

CAN

CAUSE DAMAGE

THE VEHICLE'S COMPUTER

AND/OR

DIAGNOSTIC

SYSTEMS.

AVOID

ALL

FACTORY AIRBAG

WIRING

• AIRBAGS CAN ACCIDENTALLY DEPLOY CAUSING SERIOUS INJURY

DEATH.

NOTES--------------------------

•

See

your

vehicle's instructions

for

any special tools your installation

might

require.

•

Read

all instructions accompanying your car stereo for proper

wiring

and

mounting

instructions.

[s,oP

IMPORTANT!

NOT

RETURN PRODUCT

THE RETAILER

YOU NEED ASSISTANCE OR REPLACEMENT PARTS

CALL

TOLL

FREE:

1800·621·3695 X3

HOURS: MON-FRI 8AM-5:30PM (PST) SATURDAY 8AM-2PM (PSTI

LIABILITY

DISCLAIMER

This instruction

booklet

is based

carefully documented data and research

automobile

disassembly,

wire

harness/codes

and

Information pertaining

the

installation

this kit. Scosche Industries, Inc.

cannot

held

responsible

for

discrepancies/

inconsistencies

that

may

occur

due

the

automobile manufacturing changes

options

damage

that

may

occur

the

automobile

during

the

installation

components

while

using this booklet.

you

have any

further

questions, call

our

toll

free technical

help

line

at:

1-800-621-3695x3

ITCCR01 B 07/17

Summary of content (12 pages)

PAGE 1
ITCCR01B IN-DASH INSTALLATION FOR 2015-UP CHRYSLER 300 ISO DOUBLE DIN WITH POCKET & RELOCATION PANEL KIT *DASH MODIFICATION REQUIRED (See page 3)* -----1 • Parts List: 1. UAC Top Panel (7825) 2. UAC Module 3. Narrow Pocket (7823) 4. Lower Radio Panel (7826) ----4 • Note: Vents/Knobs, Analog Clock are retained from OEM panel. Aftermarket radio is NOT included. :_ n Tools Re uired: Designed & Engineered IN U.S.A. Custom Manufactured in China NOTICE: ;.
PAGE 2
INSTALLATION GUIDE Step 1 Disassembly Disassembly Use a panel removal tool (PRT) to carefully unclip and remove the A/C control panel. ', ·~ \ \?___((.; ,. -. J ~ I /: ' .. ~~~-~ - ,\'~) ~ -~- ~ . ', ___ . ·- ·- '· . ....! . I ~- - ___ .;-_ --._:.---'_!,._ - -- - -- --- Step 2 Disassembly Unplug and remove the A/C control panel from it's location (white arrow). Retain (4) orange snapping clips (black arrows) and transfer them to the Scosche lower radio panel.
PAGE 3
Disassembly Continued INSTALLATION GUIDE Step 6 Disassembly Use a panel removal tool (PRT) to carefully unclip and remove the A/C control panel. Assembly Preparation INSTALLATION GUIDE Step 1 Preparation Remove the (3) bolts securing the OE panel clock in place and remove from the panel. Next, secure the clock onto the aftermarket Scosche panel using the OE bolts removed.
PAGE 4
INSTALLATION GUIDE Kit Assembly Before proceeding on to kit assembly be sure to install the OEM clock and airvents, see Step 1 & 2 on page 8 of the Kit Preparation process. By this point all snapping clips should already be installed onto both upper and lower Scosche panels, refer to page 2 steps 2 and 3 for refrence. Step 1 Assembly Attach both Left (7828) and Right (7827) brackets to the back of the (7826) bottom ~ radio panel using the (4) provided Phillips ,. ,.~ screws. ,,- ,. ~ ~ ,,- ,,. ; ,,.
PAGE 5
Kit Assembly INSTALLATION GUIDE Step 3 Assembly Connect all upper panel wiring, then snap the UAC panel to the vehicle's upper dash cavity. ( @) Notes: • Be sure orange snapping clips are installed to the back of the panel first, refer to Step 3 of disassembly (Page 2). • Refer to page 6 for wiring figure and codes. Step4 Assembly Connect all lower radio panel wiring , then snap the lower assembly into location.
PAGE 6
WIRING COLOR CODES V\lhite= VVhite/Black= Green= Green/Black= Black= Yellow= Red= Left Front Positive (LF+} Left Front Negative (LF-) Left Rear Positive (LR+) Left Rear Negative (LR-) Chassis Ground +12V Constant Power +12VAccessory Gray= Gray/Black= Violet= VioleUBlack= Orange= Red RCA Right Front Positive (RF+) Right Front Negative (RF-) Right Rear Positive (RR+) Right Rear Negative (RR-) Illumination VVhite RCA Navigation Outputs Red= Label Hazard Switch (PWR) Pink= Speed Pulse Lt.
PAGE 7
CLIMATE & CONVENIENCE CONTROLS Lettsc,een The Scosche Touch Screen Interface replaces the Factory climate, convenience and personalization controls built into the Factory Ford Radio/Dash panel. This solution provides improved ergonomics while adding touch screen capabilities unique to this system. Read the following sections to familiarize yourself with the operating controls and settings. FIGURE 2 Left Screen Layout 1. lime 2. 3. 4. Outside temp reading 5. Driver Air Temp Down (Cool) 6. Pass.
PAGE 8
CLIMATE & CONVENIENCE CONTROLS (RightScreenJ FIGURE 3 Right Screen Layout 1 1. 2. 3. 4. 5. 6. 7. 8. 9. SYNC Air Conditioning Front Defrost Rear Derost Recirculation ON / OFF Scosche Logo AUTO Menu CTRL SYNC * Press the Sync button (Fig.3, #1) on the touchscreen to toggle the Sync feature On/Off. Sync indicator light will illuminated when this feature is enabled. Use Sync to synchronize the passenger temperature setting with the driver temperature setting.
PAGE 9
CLIMATE & CONVENIENCE CONTROLS (RightScreenJ FIGURE 4 Right Screen Layout 2 1. Rear View Mirror Dimmer 2. Heated Steering Wheel 3. Driver Vented Seat 4. Driver Heated Seat 5. Pass. Heated Seat 6. Pass Vented Seat 7. ECO Mode 8. Head Rest Fold 9. Return Arrow [Return to Layout 1 Screen (Fig 3)] CONTROLS MENU To access the control menu touch the CTRL button on the TFT located on the right screen main layout (See page 8; fig. 3, #9).
PAGE 10
MENU NAVIGATION MENU Press the MENU button (Page 8 Fig.3, #8) to access Configuration Menu Vehicle/Interface/Language/Version Settings The following figures (4-6) are sample menu screen displays to help you navigate and understand the menu user interface of the module. Use the ~ (Return arrow) to go back to the previous menu. Press the X to close the menu window and return to the TFT color touch screen home screen.
PAGE 11
VEHICLE SETTINGS CHART Use the configuration charts below and on page 12 to help navigate through the different settings the "Menu" touch screen display has to offer. Read the charts below to familiarize yourself with the different setting options available with the ITCCR01 kit. Time/Date Hours Minutes Year Month Day Set Time Format 00-23 00-59 2000-2099 1-12 1-31 DD.MM.YYYY MM.DD.YYYY YYYY.MM.
PAGE 12
ITC SETTING CHART Picture Settings Brightness IDAYl Brightness INlahtl Automatic 0%-100% Auto 0%-100% Auto DAY/ NIGHT/ AUTOMATIC I 0% to 100% & Au1omatlc Use the negative and postlve bu1tona on the touch screen to select desired brightness percentage. Volume Prk.